一、RCC初始化
- /* Setup the microcontroller system. Initialize the Embedded Flash Interface,
- initialize the PLL and update the SystemFrequency variable. */
- SystemInit();
-
- /* Enable peripheral clocks --------------------------------------------------*/
- /* GPIOB Periph clock enable */
- //RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB, ENABLE);
-
- //启动GPIO模块时钟
- RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO, ENABLE);
- //把雕饰设置普通IO口
- GPIO_PinRemapConfig(GPIO_Remap_SWJ_Disable,ENABLE);
-
- /* I2C1 Periph clock enable */
- RCC_APB1PeriphClockCmd(RCC_APB1Periph_I2C1, ENABLE);
二、I2C_初始化
-
- /* Configure I2C1 pins: SCL and SDA */
- GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6 | GPIO_Pin_7;
- GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
- GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;
- GPIO_Init(GPIOB, &GPIO_InitStructure);
-
- I2C_InitTypeDef I2C_InitStructure;
-
- /* I2C configuration */
- I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;
- I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2;
- I2C_InitStructure.I2C_OwnAddress1 = I2C1_SLAVE_ADDRESS7;
- I2C_InitStructure.I2C_Ack = I2C_Ack_Enable;
- I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit;
- I2C_InitStructure.I2C_ClockSpeed = 100000;
-
- /* I2C Peripheral Enable */
- I2C_Cmd(I2C1, ENABLE);
- /* Apply I2C configuration after enabling it */
- I2C_Init(I2C1, &I2C_InitStructure);
三、USART初始化
- GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
- GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
- GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
- GPIO_Init(GPIOA, &GPIO_InitStructure);
-
- GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
- GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
- GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
- GPIO_Init(GPIOA, &GPIO_InitStructure);
-
- USART_InitStructure.USART_BaudRate = 115200;
- USART_InitStructure.USART_WordLength = USART_WordLength_8b;
- USART_InitStructure.USART_StopBits = USART_StopBits_1;
- USART_InitStructure.USART_Parity = USART_Parity_No;
- USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
- USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
- USART_Init(USART1, &USART_InitStructure);
- USART_Cmd(USART1, ENABLE);
四、main函数测试程序
- while (1)
- {
- I2C_EE_BufferWrite(ReadBuff, 0, 3);
- I2C_EE_BufferRead(SendBuff, 0, 3);
- Delay(0xfffff);
- fPutString(SendBuff, 15);
- }
遇到的问题,我用以前的RCC初始化程序怎么都无法启动I2C。一直在 while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT)); 中跑。
现在还没有搞清楚,I2C需要怎么设置时钟。
给主人留下些什么吧!~~
评论热议