启动2440的输出信息

启动2440的输出信息

启动2440的输出信息： Welcome to minicom 2.1 OPTIONS: History Buffer, F-key Macros, Search History Buffer, I18n Compiled on Feb 12 2006, 02:33:34. Press CTRL-A Z for help on special keys U-Boot 1.3.0-rc3 (Dec 15 2007 - 22:10:35) DRAM:  64 MB dm9000 i/o: 0x18000300, id: 0x90000a46 MAC: 00:0c:20:02:0a:5b NAND:  64 MiB In:    serial Out:   serial Err:   serial Hit any key to stop autoboot:  0 NAND read: device 0 offset 0x50000, size 0x13ff6c Reading data from 0x18fe00 -- 100% complete.  1310572 bytes read: OK ## Booting image at 33000000 ...    Image Name:   Linux-2.6.18.2    Image Type:   ARM Linux Kernel Image (uncompressed)    Data Size:    1310508 Bytes =  1.2 MB    Load Address: 30008000    Entry Point:  30008000    Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux..................................................................................... done, booting the kernel. Linux version 2.6.18.2 (root@lyl) (gcc version 3.4.1) #597 Sun Oct 12 15:48:46 JST 2008 CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177 Machine: SBZ2440 Memory policy: ECC disabled, Data cache writeback CPU S3C2440A (id 0x32440001) S3C244X: core 406.425 MHz, memory 135.475 MHz, peripheral 67.737 MHz S3C24XX Clocks, (c) 2004 Simtec Electronics CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on CPU0: D VIVT write-back cache CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets Built 1 zonelists.  Total pages: 16384 Kernel command line: root=/dev/mtdblock1 rw rootfstype=jffs2 noinitrd init=/linuxrc console=ttySAC0,115200 ip=192.168.1.7:192.168.1.21 :192.168.1.21:255.255.255.0:avantech:eth0:off irq: clearing subpending status 00000002 PID hash table entries: 512 (order: 9, 2048 bytes) timer tcon=00500000, tcnt dc7f, tcfg 00000200,00000000, usec 000016ad Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 62092KB available (2164K code, 478K data, 112K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 S3C2440: Initialising architecture SBZ: s3c244x_irq_add() S3C2440: IRQ Support S3C2440: Clock Support, DVS off Generic PHY: Registered new driver SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics DMA channel 0 at c4800000, irq 33 DMA channel 1 at c4800040, irq 34 DMA channel 2 at c4800080, irq 35 DMA channel 3 at c48000c0, irq 36 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Console: switching to colour frame buffer device 30x20 fb0: s3c2410fb frame buffer device s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440 s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440 s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440 RAMDISK driver initialized: 2 RAM disks of 41984K size 1024 blocksize loop: loaded (max 8 devices) Davicom DM9161E: Registered new driver Davicom DM9131: Registered new driver SMSC LAN83C185: Registered new driver PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered dm9000 Ethernet Driver eth0: dm9000 at c485e000,c485e004 IRQ 51 MAC: 80:e2:66:60:00:01 Linux video capture interface: v2.00 S3C24XX NAND Driver, (c) 2004 Simtec Electronics s3c2440-nand s3c2440-nand: Tacls=2, 14ns Twrph0=5 36ns, Twrph1=2 14ns NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit) Scanning device for bad blocks Creating 2 MTD partitions on "NAND 64MiB 3,3V 8-bit": 0x00000000-0x00200000 : "Kernel" 0x00200000-0x04000000 : "root partition" s3c2410-ohci s3c2410-ohci: S3C24XX OHCI s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1 s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver mice: PS/2 mouse device common for all mice ts: Compaq touchscreen protocol output s3c-buttons s3c-buttons: successfully loaded input: s3c-buttons as /class/input/input0 s3c2410 TouchScreen successfully loaded input: s3c2410 TouchScreen as /class/input/input1 S3C24XX RTC, (c) 2004,2006 Simtec Electronics s3c2410-rtc s3c2410-rtc: rtc disabled, re-enabling s3c2410-rtc s3c2410-rtc: rtc intf: dev (254:0) s3c2410-rtc s3c2410-rtc: rtc core: registered s3c as rtc0 s3c2410-sdi s3c2410-sdi: powered down. s3c2410-sdi s3c2410-sdi: initialisation done. UDA1341 audio driver initialized TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 s3c2410-rtc s3c2410-rtc: hctosys: invalid date/time s3c2410-sdi s3c2410-sdi: powered down. IP-Config: Complete:       device=eth0, addr=192.168.1.7, mask=255.255.255.0, gw=192.168.1.21,      host=avantech, domain=, nis-domain=(none),      bootserver=192.168.1.21, rootserver=192.168.1.21, rootpath= Empty flash at 0x01f30580 ends at 0x01f30600 VFS: Mounted root (jffs2 filesystem). Freeing init memory: 112K mount /etc as ramfs mount /dev as tmpfs mounting all Please press Enter to activate this console. BusyBox v1.4.1 (2007-03-25 03:24:25 CST) Built-in shell (ash) Enter 'help' for a list of built-in commands. //这里就进入了命令行了。 在上面出现的input: s3c-buttons as /class/input/input0，是将该文件在/proc建立并初始化在/sys/下。 [root@avantech /]# ls /dev/input ls: /dev/input: No such file or directory [root@avantech /]# mkdir /dev/input [root@avantech /]# mknod /dev/input/event0 c 13 2 [root@avantech /]# cat /dev/input/event0 cat: /dev/input/event0: No such device [root@avantech /]# mknod /dev/input/event0 c 13 52 mknod: /dev/input/event0: File exists [root@avantech /]# rm -f /dev/input/event0 [root@avantech /]# mknod /dev/input/event0 c 13 64 [root@avantech /]# cat /dev/input/event0 .1. ....A. ...3U [root@avantech /]# [root@avantech /]# ls arm         etc         linuxrc     opt         sys         var bin         home        lost+found  proc        tmp dev         lib         mnt         sbin        usr [root@avantech /]# ls -l  /dev/input/event0 crw-r--r--    1 root     root      13,  64 Jan  1 00:03 /dev/input/event0 [root@avantech /]# ls /proc/bus/input/devices /proc/bus/input/devices ------------------------------ 下面显示的信息，说明板子上按键事件由Sysfs=/class/input/input0处理（/dev/input/event0）， 板子上的触摸屏事件由Sysfs=/class/input/input1处理（/dev/input/event1）。 [root@avantech /]# cat /proc/bus/input/devices I: Bus=0019 Vendor=dead Product=beef Version=0001 N: Name="s3c-buttons" P: Phys= S: Sysfs=/class/input/input0 H: Handlers=kbd event0 B: EV=3 B: KEY=3c I: Bus=0013 Vendor=dead Product=beef Version=0101 N: Name="s3c2410 TouchScreen" P: Phys= S: Sysfs=/class/input/input1 H: Handlers=mouse0 event1 ts0 B: EV=b B: KEY=400 0 0 0 0 0 0 0 0 0 0 B: ABS=1000003 ------------------------------- //与/dev/input/eventx有关的，属于2.6内核的udev文件系统的支持event interface的文件。 我们可以对这件进行读写