用ibstatus命令来显示HCA的速度,ethtool命令对HCA卡无效

[root@rac1 ~]# ip addr show ----------->>>>显示ip地址
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp3s0f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP qlen 1000
    link/ether 0c:c4:7a:ac:3c:c8 brd ff:ff:ff:ff:ff:ff
    inet 192.168.100.101/24 brd 192.168.100.255 scope global enp3s0f0
       valid_lft forever preferred_lft forever
    inet 192.168.100.107/24 brd 192.168.100.255 scope global secondary enp3s0f0:1
       valid_lft forever preferred_lft forever
    inet6 fe80::ec4:7aff:feac:3cc8/64 scope link 
       valid_lft forever preferred_lft forever
3: enp3s0f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 0c:c4:7a:ac:3c:c9 brd ff:ff:ff:ff:ff:ff
4: ib0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP qlen 256
    link/infiniband 80:00:00:48:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:91:7e:d1 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    inet 10.10.10.101/24 brd 10.10.10.255 scope global ib0
       valid_lft forever preferred_lft forever
    inet6 fe80::7efe:9003:91:7ed1/64 scope link 
       valid_lft forever preferred_lft forever
5: ib1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 2044 qdisc pfifo_fast state UP qlen 256
    link/infiniband 80:00:00:49:fe:80:00:00:00:00:00:00:7c:fe:90:03:00:91:7e:d2 brd 00:ff:ff:ff:ff:12:40:1b:ff:ff:00:00:00:00:00:00:ff:ff:ff:ff
    inet 1.1.1.101/24 brd 1.1.1.255 scope global ib1
       valid_lft forever preferred_lft forever
    inet 169.254.85.174/16 brd 169.254.255.255 scope global ib1:1
       valid_lft forever preferred_lft forever
    inet6 fe80::7efe:9003:91:7ed2/64 scope link 
       valid_lft forever preferred_lft forever

[root@rac1 ~]# ethtool ib0      ---------------->>用ethtool显示HCA卡的结果
Settings for ib0:
No data available
[root@rac1 ~]# ethtool ib1      ---------------->>用ethtool显示HCA卡的结果
Settings for ib1:
No data available
[root@rac1 ~]# ethtool enp3s0f1---------------->>千兆以太网卡
Settings for enp3s0f1:
	Supported ports: [ TP ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Supported pause frame use: Symmetric
	Supports auto-negotiation: Yes
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: Yes
	Speed: Unknown!
	Duplex: Unknown! (255)
	Port: Twisted Pair
	PHYAD: 1
	Transceiver: internal
	Auto-negotiation: on
	MDI-X: off (auto)
	Supports Wake-on: pumbg
	Wake-on: d
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: no
[root@rac1 ~]# ethtool enp3s0f0 ---------------->>千兆以太网卡
Settings for enp3s0f0:
	Supported ports: [ TP ]
	Supported link modes:   10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Supported pause frame use: Symmetric
	Supports auto-negotiation: Yes
	Advertised link modes:  10baseT/Half 10baseT/Full 
	                        100baseT/Half 100baseT/Full 
	                        1000baseT/Full 
	Advertised pause frame use: Symmetric
	Advertised auto-negotiation: Yes
	Speed: 1000Mb/s
	Duplex: Full
	Port: Twisted Pair
	PHYAD: 1
	Transceiver: internal
	Auto-negotiation: on
	MDI-X: on (auto)
	Supports Wake-on: pumbg
	Wake-on: g
	Current message level: 0x00000007 (7)
			       drv probe link
	Link detected: yes
[root@rac1 ~]# 

应该用ibstatus命令来显示HCA的速度,如下所示:

[root@rac1 ~]# ibstatus
Infiniband device 'mlx4_0' port 1 status:
	default gid:	 fe80:0000:0000:0000:7cfe:9003:0091:7ed1
	base lid:	 0x1
	sm lid:		 0x7
	state:		 4: ACTIVE
	phys state:	 5: LinkUp
	rate:		 56 Gb/sec (4X FDR)  ---------->>>>注意此处
	link_layer:	 InfiniBand


Infiniband device 'mlx4_0' port 2 status:
	default gid:	 fe80:0000:0000:0000:7cfe:9003:0091:7ed2
	base lid:	 0x8
	sm lid:		 0x7
	state:		 4: ACTIVE
	phys state:	 5: LinkUp
	rate:		 56 Gb/sec (4X FDR)  ---------->>>>注意此处
	link_layer:	 InfiniBand

貌似ibstat命令也行:

[root@rac1 ~]# ibstat  
CA 'mlx4_0'
	CA type: MT4099
	Number of ports: 2
	Firmware version: 2.34.5000
	Hardware version: 0
	Node GUID: 0x7cfe900300917ed0
	System image GUID: 0x7cfe900300917ed3
	Port 1:
		State: Active
		Physical state: LinkUp
		Rate: 56                   ---------->>>>注意此处
		Base lid: 1
		LMC: 0
		SM lid: 7
		Capability mask: 0x0259486a
		Port GUID: 0x7cfe900300917ed1
		Link layer: InfiniBand
	Port 2:
		State: Active
		Physical state: LinkUp
		Rate: 56                  ---------->>>>注意此处
		Base lid: 8
		LMC: 0
		SM lid: 7
		Capability mask: 0x02594868
		Port GUID: 0x7cfe900300917ed2
		Link layer: InfiniBand
[root@rac1 ~]# 

参考文章:

Bonding over Infiniband : Link Speed of 100 Mbps is reported by bonding driver (文档 ID 1506070.1)