STM32BSP文件编写

版本

/**
 * @brief STM3210C EVAL BSP Driver version number V6.0.0
   */
#define __STM3210C_EVAL_BSP_VERSION_MAIN       (0x06) /*!< [31:24] main version */
#define __STM3210C_EVAL_BSP_VERSION_SUB1       (0x00) /*!< [23:16] sub1 version */
#define __STM3210C_EVAL_BSP_VERSION_SUB2       (0x00) /*!< [15:8]  sub2 version */
#define __STM3210C_EVAL_BSP_VERSION_RC         (0x00) /*!< [7:0]  release candidate */
#define __STM3210C_EVAL_BSP_VERSION            ((__STM3210C_EVAL_BSP_VERSION_MAIN << 24)\
                                               |(__STM3210C_EVAL_BSP_VERSION_SUB1 << 16)\
                                               |(__STM3210C_EVAL_BSP_VERSION_SUB2 << 8 )\
                                               |(__STM3210C_EVAL_BSP_VERSION_RC))

/**
  * @brief  This method returns the STM3210C EVAL BSP Driver revision
  * @retval version : 0xXYZR (8bits for each decimal, R for RC)
  */
uint32_t BSP_GetVersion(void)
{
  return __STM3210C_EVAL_BSP_VERSION;
}

LED

 * @brief LED variables
 */
GPIO_TypeDef* LED_PORT[LEDn] = {LED1_GPIO_PORT, 
                                LED2_GPIO_PORT, 
                                LED3_GPIO_PORT,
                                LED4_GPIO_PORT};

const uint16_t LED_PIN[LEDn] = {LED1_PIN, 
                                LED2_PIN, 
                                LED3_PIN,
                                LED4_PIN};

LED函数

/**
  * @brief  Configures LED GPIO.
  * @param  Led: Specifies the Led to be configured. 
  *   This parameter can be one of following parameters:
  *     @arg LED1
  *     @arg LED2
  *     @arg LED3
  *     @arg LED4
  * @retval None
  */
void BSP_LED_Init(Led_TypeDef Led)
{
  GPIO_InitTypeDef  gpioinitstruct = {0};
  
  /* Enable the GPIO_LED clock */
  LEDx_GPIO_CLK_ENABLE(Led);

  /* Configure the GPIO_LED pin */
  gpioinitstruct.Pin    = LED_PIN[Led];
  gpioinitstruct.Mode   = GPIO_MODE_OUTPUT_PP;
  gpioinitstruct.Pull   = GPIO_NOPULL;
  gpioinitstruct.Speed  = GPIO_SPEED_HIGH;

  HAL_GPIO_Init(LED_PORT[Led], &gpioinitstruct);

  HAL_GPIO_WritePin(LED_PORT[Led], LED_PIN[Led], GPIO_PIN_RESET);
}

/**
  * @brief  Turns selected LED On.
  * @param  Led: Specifies the Led to be set on. 
  *   This parameter can be one of following parameters:
  *     @arg LED1
  *     @arg LED2
  *     @arg LED3
  *     @arg LED4
  * @retval None
  */
void BSP_LED_On(Led_TypeDef Led)
{
  HAL_GPIO_WritePin(LED_PORT[Led], LED_PIN[Led], GPIO_PIN_SET);
}

/**
  * @brief  Turns selected LED Off.
  * @param  Led: Specifies the Led to be set off. 
  *   This parameter can be one of following parameters:
  *     @arg LED1
  *     @arg LED2
  *     @arg LED3
  *     @arg LED4
  * @retval None
  */
void BSP_LED_Off(Led_TypeDef Led)
{
  HAL_GPIO_WritePin(LED_PORT[Led], LED_PIN[Led], GPIO_PIN_RESET);
}

/**
  * @brief  Toggles the selected LED.
  * @param  Led: Specifies the Led to be toggled. 
  *   This parameter can be one of following parameters:
  *     @arg LED1
  *     @arg LED2
  *     @arg LED3
  *     @arg LED4
  * @retval None
  */
void BSP_LED_Toggle(Led_TypeDef Led)
{
  HAL_GPIO_TogglePin(LED_PORT[Led], LED_PIN[Led]);
}

h文件

/** @addtogroup STM3210C_EVAL_LED
  * @{
  */
#define LEDn                             4

#define LED1_PIN                         GPIO_PIN_0             /* PB.00*/
#define LED1_GPIO_PORT                   GPIOB
#define LED1_GPIO_CLK_ENABLE()           __HAL_RCC_GPIOB_CLK_ENABLE()
#define LED1_GPIO_CLK_DISABLE()          __HAL_RCC_GPIOB_CLK_DISABLE()
  
#define LED2_PIN                         GPIO_PIN_1            /* PB.01*/
#define LED2_GPIO_PORT                   GPIOB
#define LED2_GPIO_CLK_ENABLE()           __HAL_RCC_GPIOB_CLK_ENABLE()
#define LED2_GPIO_CLK_DISABLE()          __HAL_RCC_GPIOB_CLK_ENABLE()


#define LED3_PIN                         GPIO_PIN_14           /* PB.14*/
#define LED3_GPIO_PORT                   GPIOB
#define LED3_GPIO_CLK_ENABLE()           __HAL_RCC_GPIOB_CLK_ENABLE()
#define LED3_GPIO_CLK_DISABLE()          __HAL_RCC_GPIOB_CLK_ENABLE()


#define LED4_PIN                         GPIO_PIN_15            /* PB.15*/
#define LED4_GPIO_PORT                   GPIOB
#define LED4_GPIO_CLK_ENABLE()           __HAL_RCC_GPIOB_CLK_ENABLE()
#define LED4_GPIO_CLK_DISABLE()          __HAL_RCC_GPIOB_CLK_ENABLE()

#define LEDx_GPIO_CLK_ENABLE(__LED__)    do { if ((__LED__) == LED1) LED1_GPIO_CLK_ENABLE(); else \
                                              if ((__LED__) == LED2) LED2_GPIO_CLK_ENABLE(); else \
                                              if ((__LED__) == LED3) LED3_GPIO_CLK_ENABLE(); else \
                                              if ((__LED__) == LED4) LED4_GPIO_CLK_ENABLE();} while(0)

#define LEDx_GPIO_CLK_DISABLE(__LED__)   (((__LED__) == LED1) ? LED1_GPIO_CLK_DISABLE() :\
                                          ((__LED__) == LED2) ? LED2_GPIO_CLK_DISABLE() :\
                                          ((__LED__) == LED3) ? LED3_GPIO_CLK_DISABLE() :\
                                          ((__LED__) == LED4) ? LED4_GPIO_CLK_DISABLE() : 0 )

/**
  * @}
  */