u-boot-2016.05移植：(2)、修改时钟 初始化sdram 重定位u-boot 配置smdk2440.h 修改u-boot.lds

1、修改时钟：
在u-boot-2016.05\arch\arm\cpu\arm920t\start.S中将

    /*
      * 设置时钟 
      */

    /* FCLK:HCLK:PCLK = 1:2:4 */
    /* default FCLK is 120 MHz ! */
    ldr r0, =CLKDIVN
    mov r1, #3
    str r1, [r0]

替换为：

    /*
      * 设置时钟 
      */

    ldr r0, =0x4c000014
    mov r1, #0x05;            // FCLK:HCLK:PCLK=1:4:8
    str r1, [r0]

    /* 如果HDIVN非0，CPU的总线模式应该从“fast bus mode”变为“asynchronous bus mode” */
    mrc p15, 0, r1, c1, c0, 0       /* 读出控制寄存器 */ 
    orr r1, r1, #0xc0000000         /* 设置为“asynchronous bus mode” */
    mcr p15, 0, r1, c1, c0, 0       /* 写入控制寄存器 */

#define S3C2440_MPLL_400MHZ     ((0x5c<<12)|(0x01<<4)|(0x01))

    /* MPLLCON = S3C2440_MPLL_200MHZ */
    ldr r0, =0x4c000004
    ldr r1, =S3C2440_MPLL_400MHZ
    str r1, [r0]

    /* 启动ICACHE */
    mrc p15, 0, r0, c1, c0, 0   @ read control reg
    orr r0, r0, #(1<<12)
    mcr p15, 0, r0, c1, c0, 0   @ write it back

在u-boot-2016.05\board\samsung\smdk2440\smdk2440.c的board_early_init_f函数中将原来的时钟设置删掉：

    /* to reduce PLL lock time, adjust the LOCKTIME register */
    writel(0xFFFFFF, &clk_power->locktime);

    /* configure MPLL */
    writel((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV,&clk_power->mpllcon);

2、初始化sdram：
将u-boot-2016.05\board\samsung\smdk2440\lowlevel_init.S中原来的配置sdram的初始化数据

SMRDATA:
    .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
    .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
    .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
    .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
    .word ((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))
    .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
    .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
    .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
    .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
    .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
    .word 0x32
    .word 0x30
    .word 0x30

替换为我们自己的：

SMRDATA:
    .long 0x22011110     //BWSCON
    .long 0x00000700     //BANKCON0
    .long 0x00000700     //BANKCON1
    .long 0x00000700