s5pv210 uboot-2012-10移植(七) 之支持SD卡

我其实对SD卡的操作不是很熟悉，所以移植的肯定有问题，在随机赠送的Kingston 4G的SD卡上可以进行读写，但是我换了张2G的SD卡，就不行了，原因暂时先不找了，等熟悉了SD卡的操作再看看，哪位大侠知道怎么移植的一定要告诉我，不胜感激。

1.include/configs/smdkv210.h +94

#define CONFIG_GENERIC_MMC  
#define CONFIG_MMC  
#define CONFIG_SDHCI  
#define CONFIG_S5P_SDHCI  
#define CONFIG_CMD_MMC  

2.在board/samsung/smdkv210/smdkc100.c添加

int board_mmc_init (bd_t *bis)  
{  
    //printf ("haha\n");  
    #define GPG0CON  (*(volatile unsigned int *)0xE02001A0)  
    #define GPG0DRV  (*(volatile unsigned int *)0xE02001AC)  
    #define GPG3CON  (*(volatile unsigned int *)0xE0200200)  
    #define CLK_DIV4 (*(volatile unsigned int *)0xE0100310)  
    #define CLK_SRC4 (*(volatile unsigned int *)0xE0100210)  
    #define MOUTMMC (50000000) /* 50MHz */  
  
    unsigned long clk_src, clk_div, mpll, div;  
  
    //初始化MMC0 MM3管脚，4bit模式  
    GPG0CON = (0x2<<0)|(0x2<<4)|(0x2<<8)|(0x2<<12)|(0x2<<16)|(0x2<<20)|(0x2<<24);  
    GPG3CON = (0x2<<0)|(0x2<<4)|(0x2<<8)|(0x2<<12)|(0x2<<16)|(0x2<<20)|(0x2<<24);  
    //GPG0DRV = 0x3fdf;  
  
    //初始化SD时钟  
    clk_src = CLK_SRC4;  
    clk_src &= ~((0xf << 12) | 0xf);  
    clk_src |= (0x6 << 12) | 0x6;   
  
        mpll = get_pll_clk(MPLL);  
    div = ((mpll + MOUTMMC) / MOUTMMC) - 1;  
  
    clk_div = CLK_DIV4;  
    clk_div &= ~((0xf << 12) | 0xf);  
    clk_div |= (div << 12) | div;  
  
    CLK_SRC4 = clk_src;  
    CLK_DIV4 = clk_div;  
      
    return s5p_sdhci_init(0xEB000000, 0, 4)|s5p_sdhci_init(0xEB300000, 1, 4);  
}

3.修改drivers/mmc/sdhci.c +133

 /* Wait max 10 ms */  
    timeout = 10;  
#if 0  
    sdhci_writel(host, SDHCI_INT_ALL_MASK, SDHCI_INT_STATUS);  
    mask = SDHCI_CMD_INHIBIT | SDHCI_DATA_INHIBIT;  
  
    /* We shouldn't wait for data inihibit for stop commands, even 
       though they might use busy signaling */  
    if (cmd->cmdidx == MMC_CMD_STOP_TRANSMISSION)  
        mask &= ~SDHCI_DATA_INHIBIT;  
#endif  
  
    /* 
     * PRNSTS 
     * CMDINHDAT[1] : Command Inhibit (DAT) 
     * CMDINHCMD[0] : Command Inhibit (CMD) 
     */  
    mask = (1 << 0);  
    if ((data != NULL) || (cmd->resp_type & MMC_RSP_BUSY))  
        mask |= (1 << 1);  
  
    /* 
     * We shouldn't wait for data inihibit for stop commands, even 
     * though they might use busy signaling 
     */  
    if (data)  
        mask &= ~(1 << 1);  
  
    //mask = 1;  
    //printf ("mask: %08x\n  read: %08x\n", mask, sdhci_readl(host, SDHCI_PRESENT_STATE));  
    while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {  
        if (timeout == 0) {  
            printf("Controller never released inhibit bit(s).\n");  
            return COMM_ERR;  
        }  
        timeout--;  
        udelay(1000);  
    } 

4.修改drivers/mmc/mmc.c把sd_change_freq中的最后两个returne err; 给屏蔽掉

//if (err)  
        //return err; 

5.make，使用命令烧入SD卡里，启动开发板