华三(h3c)交换机操作命令详解vlan切换

程序员都很懒，你懂的！

1. 十年生死两茫茫，写程序，到天亮。  
2. 千行代码，Bug何处藏。   
3. 纵使上线又怎样，朝令改，夕断肠。   
4. 领导每天新想法，天天改，日日忙。  
5. 相顾无言，惟有泪千行。  
6. 每晚灯火阑珊处，夜难寐，又加班。

闲话少说，直接上代码：

华三交换机操作命令
输入用户名回车,输入密码后回车。再输入sys进入系统模式。
或者输入登录后，输入system-view进入系统模式。
显示/查看vlan
display brief interface 
显示vlan列表后，进入6号口命令
interface Eth1/0/6 
或者interface et1/0/6
或者interface Ethernet 1/0/6
切换到vlan 200的命令
port access vlan 200
再切换到原理的vlan的命令
undo port access vlan

以上红色字体为实际命令，端口和vlan编号都是以博主所在公司的vlan编号！

其他命令列表：

  acl                      Specify acl configuration information
  am                       Access management
  apply                    Specify profile configuration
  arp                      Add static ARP entry 
  bpdu-tunnel              Global Enable tunneling protocol frame
  broadcast-suppression    Specify the broadcast storm control
  burst-mode               Specify burst-mode
  change                   Change the unit id of specified unit to a new value
  cluster                  Specify cluster configuration information
  command-alias            Specify command alias 
  command-privilege        Specify the command level 
  copy                     Copy source port configuration to destination port
  copyright-info           Displaying copyright information
  cut                      Cut connection
  delete                   Delete route information
  detect-group             Specify detect-group view
  dhcp                     DHCP configuration subcommands 
  dhcp-security            Specify DHCP(Dynamic Host Configuration Protocol) 
                           relay security configuration information
  dhcp-server              Specify DHCP(Dynamic Host Configuration Protocol) 
                           relay configuration information
  dhcp-snooping            DHCP snooping
  display                  Display current system information
  dldp                     Specify configuration information of DLDP
  dns                      Specify domain name system 
  domain                   Add domain or modify domain attributes
  dot1x                    Specify 802.1X configuration information 
  end-station              Configure ip address of end station 
  execute                  Batch Command
  fabric                   Fabric
  fabric-port              Fabric-port link-type
  file                     Specify file system configuration information
  ftm                      Fabric topology management 
  ftp                      Specify FTP server configuration information
  ftp-server               Specify a source IP 
  garp                     Generic Attribute Registration Protocol
  giant-frame              Giant frame management
  gratuitous-arp-learning  Gratuitous Arp learning function 
  gvrp                     GARP VLAN Registration Protocol
  habp                     Specify HABP configuration information
  header                   Specify the login banner 
  hwping                   Specify HWPing test class
  hwping-agent             Specify HWPing agent task function
  hwping-server            Specify HWPing server task function
  hwtacacs                 Specify HWTACACS server
  icmp                     Specify ICMP(the Internet Control Message Protocol) 
                           configuration information 
  igmp-snooping            IGMP snooping 
  info-center              Specify information center configuration information
  interface                Specify the interface configuration view 
  ip                       Specify IP(Internet Protocol) configuration 
                           information 
  irf-fabric               IRF feature in fabric 
  job                      Schedule a system task
  lacp                     Configure LACP Protocol
  link-aggregation         Configure a link aggregation group
  lldp                     Link Layer Discovery Protocol(802.1ab) 
  local-server             Specify local RADIUS server configuration 
                           information 
  local-user               Specify local user configuration information
  loopback-detection       Detect if loopback exists
  mac-address              Quick notify Arp entry function 
  mac-authentication       Specify MAC authentication configuration information
  management-vlan          Specify management-vlan
  memory                   Free memory for routing protocols to run normally
  mib-style                MIB style
  mirroring                Specify mirroring
  mirroring-group          Specify mirroring-group
  monitor-link             Configure Monitor Link 
  msdp                     Specify MSDP(Multicast Source Discovery Protocol) 
                           configuration information
  msdp-tracert             MSDP trace route to source RP
  mtracert                 Trace route to multicast source
  multicast                Specify multicast configuration information
  multicast-source-deny    Multicast source port deny
  ndp                      Neighbor discovery protocol
  nslookup                 Query Internet name servers
  ntdp                     Specify NTDP configuration information
  ntp-service              Specify NTP(Network Time Protocol) configuration 
                           information
  ospf                     Specify OSPF(Open Shortest Path First) configuration 
                           information
  packet-filter            Filter packets based on acl
  patch                    Patch module
  pim                      Specify PIM(Protocol Independent Multicast) 
                           configuration information
  ping                     Ping function 
  pki                      Specify PKI module configuration information
  poe                      Power over Ethernet
  poe-profile              Poe-profile
  port-mac                 Config port MAC start address 
  port-security            Specify port-security configuration information 
  protocol-priority        Specify protocol-priority configuration information
  public-key               Specify public-key module configuration information
  qos                      QoS configuration information
  qos-profile              Specify qos-profile configuration information
  queue-scheduler          Specify queue scheduling mode and parameters
  quit                     Exit from current command view
  radius                   Specify RADIUS configuration information
  resilient-arp            Resilient ARP module 
  return                   Exit to User View 
  rip                      Specify RIP(Routing Information Protocol) 
                           configuration information
  rmon                     Specify RMON
  route-policy             Specify a route policy
  router                   Configure router information
  rsa                      Specify RSA module configuration information
  save                     Save current configuration
  schedule                 Schedule system task
  set                      Set the unit name of specified unit 
  sftp                     Set SFTP service attribute
  smart-link               Configure Smart Link 
  snmp-agent               Specify SNMP(Simple Network Management Protocol) 
                           configuration information
  ssh                      Specify SSH (secure shell) configuration information
  ssh-server               Specify a source IP 
  ssh2                     Open a secure shell client connection 
  ssl                      Specify SSL (Secure Socket Layer) configuration 
                           information
  storm-constrain          Port storm-constrain
  stp                      Spanning tree protocol 
  super                    Modify super password parameters 
  sysname                  Specify system name and the command line prompt 
  system-guard             System-guard module options 
  system-monitor           Specify system-monitor configuration information
  tcp                      Specify TCP(Transmission Control Protocol) 
                           configuration information 
  telnet                   Establish one TELNET connection 
  telnet-server            VTY module 
  tftp                     Open TFTP connection 
  tftp-server              TFTP Server 
  time-range               Specify time-range configuration information
  tracemac                 Trace MAC function
  tracert                  Trace route function 
  traffic-priority         Specify new priority of the packets
  udp-helper               UDP HELPER module
  undo                     Cancel current setting
  unknown-multicast        Unknown multicast
  user-interface           Configure the user terminal interface 
  vlan                     Configure VLAN
  vlan-vpn                 Specify vlan-vpn
  voice                    Specify voice vlan
  vrrp                     Specify configuration information of VRRP
  web-authentication       Web-Authentication configuration information 
  webcache                 Specify configuration information for webcache 
                           redirection

如有不懂，请进QQ群 135430763,互相学习！！！