linux内核移植生成uImage映象文件参考

1、先修改顶层Makefile，如下：

ARCH                     ?= $ (SUBARCH)

CROSS_COMPILE      ?=

改为：

ARCH                     ?= arm

CROSS_COMPILE      ?=  arm－linux－

2、执行make s3c2410_defconfig

3、make uImage，首次编译完内核用了4分钟，尾部出现如下信息：

   LD      arch/arm/boot/compressed/vmlinux
  OBJCOPY arch/arm/boot/zImage
  Kernel: arch/arm/boot/zImage is ready
  UIMAGE  arch/arm/boot/uImage
"mkimage" command not found - U-Boot images will not be built
  Image arch/arm/boot/uImage is ready

4、cd  arch/arm/boot/

 在这个目录下面没有发现uImage的身影，于是把zImage烤贝到 /var/lib/tftpboot下面。

然后通过在u-boot下面执行命令来烧写到板里。

5、在u-boot下面操作如下：

OpenJTAG> tftp 0x32000000 zImage
dm9000 i/o: 0x28000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 08:00:3e:26:0a:5b
TFTP from server 172.22.136.38; our IP address is 172.22.136.55
Filename 'zImage'.
Load address: 0x32000000
Loading: checksum bad
T #################################################################
     #################################################################
     #################################################################
     #################################################################
     ####################################
done
Bytes transferred = 1511056 (170e90 hex)
OpenJTAG> bootm 0x32000000
## Booting image at 32000000 ...
6、从上面可以看出没有出现内核信息，于是从新回到pc机上编译内核完成的地方来查看问题出在哪？

看到这一行："mkimage" command not found - U-Boot images will not be built

                    可以看出缺少mkimage这个命令。

7、上网查了点资料，在编译完成的u-boot-1.1.6的tool/下面找到mkimage这个文件，

把它烤贝到交叉编译的路径下面/work/tools/gcc-3.4.5-glibc-2.3.6/bin

8、重新再进入顶层，再进行内核编译，这次成功产生如下信息：

OBJCOPY arch/arm/boot/Image
  Kernel: arch/arm/boot/Image is ready
  AS      arch/arm/boot/compressed/head.o
  GZIP    arch/arm/boot/compressed/piggy.gz
  AS      arch/arm/boot/compressed/piggy.o
  CC      arch/arm/boot/compressed/misc.o
  LD      arch/arm/boot/compressed/vmlinux
  OBJCOPY arch/arm/boot/zImage
  Kernel: arch/arm/boot/zImage is ready
  UIMAGE  arch/arm/boot/uImage
Image Name:   Linux-2.6.22.6
Created:      Sun Dec  6 22:33:55 2009
Image Type:   ARM Linux Kernel Image (uncompressed)
Data Size:    1511064 Bytes = 1475.65 kB = 1.44 MB
Load Address: 0x30008000
Entry Point:  0x30008000
  Image arch/arm/boot/uImage is ready

9、在arch/arm/boot

我们这一次可以看到uImage这个文件，不过此时还不是可执行文件，现在更改权限

chmod 777 uImage

顔色变为绿色。。。。

10、在u-boot下继续操作，如下：

Enter your selection: q
OpenJTAG> tftp 0x32000000 uImage
dm9000 i/o: 0x28000300, id: 0x90000a46
DM9000: running in 16 bit mode
MAC: 08:00:3e:26:0a:5b
TFTP from server 172.22.136.38; our IP address is 172.22.136.55
Filename 'uImage'.
Load address: 0x32000000
Loading: checksum bad
checksum bad
T #################################################################
     #################################################################
     #################################################################
     #################################################################
     ####################################
done
Bytes transferred = 1511128 (170ed8 hex)
OpenJTAG> bootm 0x32000000
## Booting image at 32000000 ...
   Image Name:   Linux-2.6.22.6
   Created:      2009-12-06  14:33:55 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1511064 Bytes =  1.4 MB
   Load Address: 30008000
   Entry Point:  30008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux................................................................................................... done, booting the kernel.
Linux version 2.6.22.6 (root@huanghuang-desktop) (gcc version 3.4.5) #1 Sun Dec 6 22:33:51 CST 2009
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
Machine: SMDK2410
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410A (id 0x32410002)
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0
irq: clearing subpending status 00000002
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61696KB available (2788K code, 313K data, 132K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2410: Initialising architecture
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
s3c2410-lcd s3c2410-lcd: no platform data for lcd, cannot attach
s3c2410-lcd: probe of s3c2410-lcd failed with error -22
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2410-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
dm9000 Ethernet Driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
BAST NOR-Flash Driver, (c) 2004 Simtec Electronics
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand s3c2410-nand: Tacls=3, 30ns Twrph0=7 70ns, Twrph1=3 30ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 8 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00004000 : "Boot Agent"
0x00000000-0x00200000 : "S3C2410 flash partition 1"
0x00400000-0x00800000 : "S3C2410 flash partition 2"
0x00800000-0x00a00000 : "S3C2410 flash partition 3"
0x00a00000-0x00e00000 : "S3C2410 flash partition 4"
0x00e00000-0x01800000 : "S3C2410 flash partition 5"
0x01800000-0x03000000 : "S3C2410 flash partition 6"
0x03000000-0x04000000 : "S3C2410 flash partition 7"
usbmon: debugfs is not available
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2410-i2c s3c2410-i2c: slave address 0x10
s3c2410-i2c s3c2410-i2c: bus frequency set to 390 KHz
s3c2410-i2c s3c2410-i2c: i2c-0: S3C I2C adapter
TCP cubic registered
NET: Registered protocol family 1
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
List of all partitions:
1f00         16 mtdblock0 (driver?)
1f01       2048 mtdblock1 (driver?)
1f02       4096 mtdblock2 (driver?)
1f03       2048 mtdblock3 (driver?)
1f04       4096 mtdblock4 (driver?)
1f05      10240 mtdblock5 (driver?)
1f06      24576 mtdblock6 (driver?)
1f07      16384 mtdblock7 (driver?)
No filesystem could mount root, tried:  ext3 ext2 cramfs msdos vfat romfs
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
从上面可以看到内核的启动信息。

11、Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)

这一行信息，是因为我们还没有修改MTD分区，没有增加对yaffs文件系统的支持 。