华为模拟器基础命令

基础命令

<Huawei>undo terminal trapping  							//关闭日志
[Huawei]user-interface console 0  							//进入cons口
[Huawei-ui-console0]authentication-mode password 
[Huawei-ui-console0]set authentication password cipher 123 		//配置密文密码
[Huawei-ui-console0]return 									//返回用户试图
[Huawei]ip route-static 192.168.1.0 24 192.168.2.2  		//配置静态路由
[Huawei]ip route-static 0.0.0.0 0.0.0.0 192.168.2.2  		//配置默认路由
[Huawei]vlan 2  												//建立vlan 2
[Huawei]int Ethernet0/0/0  								//进入0/0/0接口
[Huawei-Ethernet0/0/0]port link-type access 			//端口设置为access
[Huawei-Ethernet0/0/0]port default vlan 2   		//加入vlan 2
[Huawei]int g0/0/1 //进入0/0/1接口
[Huawei-GigabitEthernet0/0/1]port like-type trunk //端口设置为trunk
[Huawei-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 3 //允许vlan2 3通过
[Huawei]dis vlan 							//查看vlan
[Huawei]dis current-configuration  			//查看配置
[Huawei]quit  									//退出当前模式
[Huawei-ui-console0]undo authentication-mode 		//取消console密码认证
[Huawei]telnet server  enable 						//启动vty远程服务
[Huawei]user-interface vty 0 4 								//进入vty接口
[Huawei-ui-vty0-4]set authentication password ? 			//查看密码配置
[Huawei-ui-vty0-4]set authentication password cipher 123 		//设置密文密码
[Huawei]dis ip routing-table 			//查看路由表
[Huawei]sysname r1 						//更改设备名称

配置基础命令

[r1]int g0/0/0  						//进入0/0/0接口
[r1-GigabitEthernet0/0/0]int g0/0/0.1 				//进入0/0/0.1子接口
[r1-GigabitEthernet0/0/0.1]dot1q termination vid 11  	//子接口与vlan11关联
[r1-GigabitEthernet0/0/0.1]ip add 192.168.1.1 24 		//配制IP地址
[r1-GigabitEthernet0/0/0.1]arp broadcast enable  		//开启arp广播
[sw1]vlan batch 10 20   		//创建多个vlan
[sw1]interface Vlanif 10 		//进入vlan接口
[sw1]dis vlan  						//查看vlan信息
[r1]dis ospf routing 				//查看OSPF路由表
[r1]dis ospf peer 					//查看邻居列表及状态
[r1]dis ospf lsdb  					//查看链路状态数据库
[r1]dis ospf interface 			//查看ospf接口信息
[r1]ospf router-id 1.1.1.1 		//路由器设定route-id
[r1-ospf-1]area 0      			//设置区域，默认设置area 0
[r1-ospf-1-area-0.0.0.0]network 10.0.0.0 0.0.0.255  		//宣告该路由器直连网段（0.0.0.255为反掩码）