gd32串口接收

#include"stdio.h"
#include"gd32f30x.h"
#include"keydiver.h"
int a[10]={0};
	int i=0;
unsigned data;
int c,d;
unsigned char databuffer[128]={0};
volatile int db_wpos=0;
volatile int db_rpos=0;
#define data_buffer_len  sizeof(databuffer)
char databufferhasdata(){
	return db_wpos!=db_rpos;
}



char databufferwrite(unsigned char data){
	int pos=db_wpos;
	databuffer[pos]=data;
	if(pos+1<data_buffer_len){++db_wpos;}
	else{db_wpos=0;}
}
unsigned char databufferread(){
	int pos=db_rpos;
	if(pos+1<data_buffer_len){++db_rpos;}
	else{db_rpos=0;}
	return databuffer[pos];
}

void usartsend(int usart,int c)
{
	
while(!usart_flag_get(usart,USART_FLAG_TBE));
       

		usart_data_transmit(usart,c);
		while(!usart_flag_get(usart,USART_FLAG_TC));
		
}
unsigned char usartrecvbyte(uint32_t usart,unsigned char dat){
	while(!usart_flag_get(usart,USART_FLAG_RBNE));
	return usart_data_receive(usart);
}
	
	
void USART0_IRQHandler()
{
	 if(usart_interrupt_flag_get(USART0,USART_INT_FLAG_RBNE)){
		 usart_interrupt_flag_clear(USART0,USART_INT_FLAG_RBNE);
		 data=usart_data_receive(USART0);
		 databufferwrite(data);
} 
	}

int main()
{
	int i;
	rcu_periph_clock_enable(RCU_GPIOA);
	rcu_periph_clock_enable(RCU_AF);
	rcu_periph_clock_enable(RCU_USART0);
  gpio_init(GPIOA,GPIO_MODE_AF_PP,GPIO_OSPEED_2MHZ,GPIO_PIN_9);
	gpio_init(GPIOA,GPIO_MODE_IPU,GPIO_OSPEED_2MHZ,GPIO_PIN_10);

	/*
		rcu_periph_clock_enable(RCU_GPIOB);

	
	  gpio_init(GPIOA,GPIO_MODE_AF_PP,GPIO_OSPEED_2MHZ,GPIO_PIN_6);
gpio_pin_remap_config(GPIO_USART0_REMAP,ENABLE);//
	*/
	usart_deinit(USART0);
  usart_baudrate_set(USART0,9600);
	usart_parity_config(USART0,USART_PM_NONE);
  usart_word_length_set(USART0,USART_WL_8BIT);
	usart_stop_bit_set(USART0,USART_STB_1BIT);
	usart_transmit_config(USART0,USART_TRANSMIT_ENABLE);
	usart_receive_config(USART0,USART_RECEIVE_ENABLE);
	usart_enable(USART0);
	usart_interrupt_enable(USART0,USART_INT_RBNE);
	nvic_irq_enable(USART0_IRQn,2,2);


while(1){
	if(2==scanf("%d+%d",&c,&d)){
		printf("%d+%d=%d",c,d,c+d);
}
}
}
int fputc(int c, FILE * f){
		usartsend(USART0,c);
	return c;
}
int fgetc(FILE*f){
while(!databufferhasdata());
	return databufferread();
}
	
	

在串口发送的基础上继续配置串口接收，由串口发送可知，接收是对应的是PA10引脚，因此打开PA10，打开串口接收，并且配置接收中断，接收函数就是将串口接收到的内容返回，进入函数中断先用data接收串口接收的内容，通过bufferread将内容保存到数组中，然后编写scanf函数，使它具有接收功能，最后将输入的数用scanf函数接收后，又通过printf函数发送出去。