在所有节点上执行chrony服务安装命令,将主节点设置时间服务器,其他的节点都从主节点同步时间。
# 安装服务
yum -y install chrony
# 查看状态
systemctl status chronyd
# 重启chronyd
systemctl restart chronyd
二、检查设置时区
在所有节点上设置统一的时间区域,本文中将其设置为亚洲时区,用户可自行定义。
# 查看时区
[root@x ~]# timedatectl
Local time: Sun 2022-04-17 11:15:48 CST
Universal time: Sun 2022-04-17 03:15:48 UTC
RTC time: Sun 2022-04-17 11:15:48
Time zone: Asia/Shanghai (CST, +0800)
NTP enabled: yes
NTP synchronized: yes
RTC in local TZ: yes
DST active: n/a
# 筛选式查看在亚洲S开的上海可用时区:
[root@x ~]# timedatectl list-timezones | grep -E "Asia/S.\*"
Asia/Sakhalin
Asia/Samarkand
Asia/Seoul
Asia/Shanghai
Asia/Singapore
Asia/Srednekolymsk
# 设置当前系统为Asia/Shanghai上海时区:
[root@x ~]# timedatectl set-timezone Asia/Shanghai
# 修改日期时间(可选,主节时钟源无法同步,可以先关闭NTP同步)
timedatectl set-ntp false
timedatectl set-time "2022-04-17 15:50:20"
# 开启 NTP
timedatectl set-ntp true
#设置完时区后,强制同步下系统时钟:
[root@x ~]# chronyc -a makestep
200 OK
三、防火墙设置
因NTP使用123/UDP端口协议,所以允许NTP服务即可。但是我一般都会把防火墙和selinux禁止。
# 查看防火墙状态
[root@x ~]# systemctl status firewalld.service
● firewalld.service - firewalld - dynamic firewall daemon
Loaded: loaded (/usr/lib/systemd/system/firewalld.service; disabled; vendor preset: enabled)
Active: inactive (dead)
Docs: man:firewalld(1)
# 启动防火墙
[root@x ~]# systemctl start firewalld.service
# 防火墙内放行NTP服务
[root@x ~]# firewall-cmd --add-service=ntp --permanent
success
# reload才能生效
[root@x ~]# firewall-cmd --reload
success
内部访问一般直接关闭防火墙
[root@x ~]# systemctl stop firewalld
[root@x ~]# systemctl disalbe firewalld
四、配置Chrony
1.服务器端配置
将主节点设置为内部NTP Server,编辑“/etc/chrony.conf”文件,如有公网的情况,可以配置阿里云的ntp服务地址作为源 。
ntp1.aliyun.com
授时中心参考
- 210.72.145.44 国家授时中心
- ntp.aliyun.com 阿里云
- s1a.time.edu.cn 北京邮电大学
- s1b.time.edu.cn 清华大学
- s1c.time.edu.cn 北京大学
- s1d.time.edu.cn 东南大学
- s1e.time.edu.cn 清华大学
- s2a.time.edu.cn 清华大学
- s2b.time.edu.cn 清华大学
- s2c.time.edu.cn 北京邮电大学
- s2d.time.edu.cn 西南地区网络中心
- s2e.time.edu.cn 西北地区网络中心
- s2f.time.edu.cn 东北地区网络中心
- s2g.time.edu.cn 华东南地区网络中心
- s2h.time.edu.cn 四川大学网络管理中心
- s2j.time.edu.cn 大连理工大学网络中心
- s2k.time.edu.cn CERNET桂林主节点
- s2m.time.edu.cn 北京大学
- ntp.sjtu.edu.cn 202.120.2.101 上海交通大学
master01作为服务端,当前节点IP地址为172.16.24.65,网段是172.16.24.0/24,配置详情如下
server ntp1.aliyun.com iburst
allow 172.16.24.0/24
local stratum 10
[root@master01 ~]# vim /etc/chrony.conf
# Use public servers from the pool.ntp.org project.
# Please consider joining the pool (http://www.pool.ntp.org/join.html).
# server 0.centos.pool.ntp.org iburst
# server 1.centos.pool.ntp.org iburst
# server 2.centos.pool.ntp.org iburst
#server 3.centos.pool.ntp.org iburst
# 公网时间服务器
server ntp1.aliyun.com iburst
# Record the rate at which the system clock gains/losses time.
driftfile /var/lib/chrony/drift
# Allow the system clock to be stepped in the first three updates
# if its offset is larger than 1 second.
makestep 1.0 3
# Enable kernel synchronization of the real-time clock (RTC).
rtcsync
# Enable hardware timestamping on all interfaces that support it.
#hwtimestamp \*
# Increase the minimum number of selectable sources required to adjust
# the system clock.
#minsources 2
# Allow NTP client access from local network.
# 指定一台主机、子网,或者网络以允许或拒绝访问本服务器
allow 172.16.24.0/24
# Serve time even if not synchronized to a time source.
# 即使server指令中时间服务器不可用,也允许将本地时间作为标准时间授时给其它客户端chronyc命令
local stratum 10
# Specify file containing keys for NTP authentication.
#keyfile /etc/chrony.keys
# Specify directory for log files.
logdir /var/log/chrony
# Select which information is logged.
#log measurements statistics tracking
2.客户端节点配置
其他work节点使用主节点(master01)作为时钟源,增加内网时钟源
server master01 iburst
[root@worker01 ~]# vim /etc/chrony.conf
# Use public servers from the pool.ntp.org project.
# Please consider joining the pool (http://www.pool.ntp.org/join.html).
# server 0.centos.pool.ntp.org iburst
# server 1.centos.pool.ntp.org iburst
# server 2.centos.pool.ntp.org iburst
#server 3.centos.pool.ntp.org iburst
# 内网时钟服务端
server master01 iburst
# Record the rate at which the system clock gains/losses time.
driftfile /var/lib/chrony/drift
# Allow the system clock to be stepped in the first three updates
# if its offset is larger than 1 second.
makestep 1.0 3
# Enable kernel synchronization of the real-time clock (RTC).
rtcsync
# Enable hardware timestamping on all interfaces that support it.
#hwtimestamp \*
# Increase the minimum number of selectable sources required to adjust
# the system clock.
#minsources 2
# Allow NTP client access from local network.
#allow 192.168.0.0/16
# Serve time even if not synchronized to a time source.
#local stratum 10
# Specify file containing keys for NTP authentication.
#keyfile /etc/chrony.keys
# Specify directory for log files.
logdir /var/log/chrony
# Select which information is logged.
#log measurements statistics tracking
3.配置文件说明:
/etc/chrony.conf
- server
可用于时钟服务器,iburst 选项当服务器可达时,发送一个八个数据包而不是通常的一个数据包。 包间隔通常为2秒,可加快初始同步速度,这个可以添加外网服务器或者内网服务器,域名或者IP都可以。 - driftfile
根据实际时间计算出计算机增减时间的比率,将它记录到一个文件中,会在重启后为系统时钟作出补偿 - stratumweight
stratumweight指令设置当chronyd从可用源中选择同步源时,每个层应该添加多少距离到同步距离。默认情况下,CentOS中设置为0,让chronyd在选择源时忽略源的层级。 - rtcsync
启用内核模式,系统时间每11分钟会拷贝到实时时钟(RTC) - allow / deny
指定一台主机、子网,或者网络以允许或拒绝访问本服务器 - cmdallow / cmddeny
可以指定哪台主机可以通过chronyd使用控制命令 - bindcmdaddress
允许chronyd监听哪个接口来接收由chronyc执行的命令 - makestep
通常chronyd将根据需求通过减慢或加速时钟,使得系统逐步纠正所有时间偏差。在某些特定情况下,系统时钟可能会漂移过快,导致该调整过程消耗很长的时间来纠正系统时钟。该指令强制chronyd在调整期大于某个阀值时调整系统时钟 - local stratum 10
即使server指令中时间服务器不可用,也允许将本地时间作为标准时间授时给其它客户端chronyc命令
四、启动chrony服务
在所有节点上将其配置为在系统引导时启动。
# 设置开机启动
[root@x~]# systemctl enable chronyd.service
# 重启服务
[root@x~]# systemctl restart chronyd.service
# 查看时间同步状态
[root@x~]# timedatectl status
# 手动强制同步下系统时钟
[root@x~]# chronyc -a makestep
# 查看时间同步源
[root@x~]# chronyc sources -v
# 查看时间同步源状态
[root@x~]# chronyc sourcestats -v
# 硬件时间默认为UTC
[root@x~]# timedatectl set-local-rtc 1
# 启用NTP时间同步
[root@x~]# timedatectl set-ntp yes
五、chronyc相关命令
- help 命令可以查看更多chronyc的交互命令
- accheck 检查是否对特定主机可访问当前服务器
- activity 显示有多少NTP源在线/离线
- sources [-v] 显示当前时间源的同步信息
- sourcestats [-v] 显示当前时间源的同步统计信息
- add server 手动添加一台新的NTP服务器
- clients 报告已访问本服务器的客户端列表
- delete 手动移除NTP服务器或对等服务器
- settime 手动设置守护进程时间
- sracking 显示系统时间信息
- chronyc sources 主要用于查看时钟源授时时间偏差值。
[root@iZbp1fy7y89tqjvmlp1dvhZ ~]# chronyc sources
210 Number of sources = 15
MS Name/IP address Stratum Poll Reach LastRx Last sample
===============================================================================
^+ 120.25.115.20 2 10 255 987 -982us[ -985us] +/- 15ms
^? 10.143.33.49 0 10 0 - +0ns[ +0ns] +/- 0ns
^+ 100.100.3.1 2 10 377 112 +126us[ +126us] +/- 1601us
^+ 100.100.3.2 2 10 377 258 -75us[ -75us] +/- 1738us
^+ 100.100.3.3 2 10 375 720 -191us[ -191us] +/- 1708us
^+ 203.107.6.88 2 10 377 344 +2988us[+2988us] +/- 18ms
^? 10.143.33.50 0 10 0 - +0ns[ +0ns] +/- 0ns
^? 10.143.33.51 0 10 0 - +0ns[ +0ns] +/- 0ns
^? 10.143.0.44 0 10 0 - +0ns[ +0ns] +/- 0ns
^? 10.143.0.45 0 10 0 - +0ns[ +0ns] +/- 0ns
^? 10.143.0.46 0 10 0 - +0ns[ +0ns] +/- 0ns
^+ 100.100.5.1 2 10 377 537 +324us[ +324us] +/- 1975us
^+ 100.100.5.2 2 10 377 269 -209us[ -209us] +/- 1946us
^+ 100.100.5.3 2 10 377 281 +126us[ +126us] +/- 2078us
^* 100.100.61.88 1 10 377 913 -465us[ -468us] +/- 11ms
这里总共输出8列信息,分别对应含义如下:
列名 | 含义 | 具体说明 |
---|---|---|
M | 表示授时时钟源 | ^表示服务器,= 表示二级时钟源 ,#表示本地连接的参考时钟 |
S | 指示源的状态 | *当前同步的源,+表示其他可接受的源,?表示连接丢失的源,x表示一个认为是falseticker 的时钟(即它的时间与大多数其他来源不一致),~表示其时间似乎具有太多可变性的来源 |
Name/IP address | 表示源的名称或IP地址,或者参考时钟的refid值 | 无 |
Stratum | 表示源的层级 | 层级1表示本地连接的参考时钟,第2层表示通过第1层级计算机的时钟实现同步,依此类推。 |
Poll | 表示源轮询的频率 | 以秒为单位,值是基数2的对数,例如值6表示每64秒进行一次测量,chronyd会根据当时的情况自动改变轮询频率 |
Reach | 表示源的可达性的锁存值(八进制数值) | 该锁存值有8位,并在当接收或丢失一次时进行一次更新,值377表示最后八次传输都收到了有效的回复 |
LastRx | 表示从源收到最近的一次的时间 | 通常是几秒钟,字母m,h,d或y分别表示分钟,小时,天或年,值10年表示从未从该来源收到时间同步信息 |
Last sample | 表示本地时钟与上次测量时源的偏移量 | 方括号中的数字表示实际测量的偏移值,这可以以ns(表示纳秒),us(表示微秒),ms(表示毫秒)或s(表示秒)为后缀;方括号左侧的数字表示原始测量值,这个值是经过调整以允许应用于本地时钟的任何偏差;方括号右侧表示偏差值,+/-指示器后面的数字表示测量中的误差范围,+偏移表示本地时钟快速来源 |
- chronyc sourcestats 主要偏移率及每个时钟源的偏移评估值:
[root@iZbp1fy7y89tqjvmlp1dvhZ ~]# chronyc sourcestats
210 Number of sources = 15
Name/IP Address NP NR Span Frequency Freq Skew Offset Std Dev
==============================================================================
120.25.115.20 37 15 12h -0.001 0.024 -216us 516us
10.143.33.49 0 0 0 +0.000 2000.000 +0ns 4000ms
100.100.3.1 26 18 431m -0.001 0.004 +94us 44us
100.100.3.2 22 12 362m +0.001 0.005 +5134ns 44us
100.100.3.3 17 9 362m -0.003 0.006 -236us 38us
203.107.6.88 64 32 18h +0.013 0.039 +553us 1730us
10.143.33.50 0 0 0 +0.000 2000.000 +0ns 4000ms
10.143.33.51 0 0 0 +0.000 2000.000 +0ns 4000ms
10.143.0.44 0 0 0 +0.000 2000.000 +0ns 4000ms
10.143.0.45 0 0 0 +0.000 2000.000 +0ns 4000ms
10.143.0.46 0 0 0 +0.000 2000.000 +0ns 4000ms
100.100.5.1 16 8 258m +0.001 0.009 +321us 44us
100.100.5.2 17 8 276m +0.001 0.007 -219us 35us
100.100.5.3 21 11 344m +0.001 0.006 +80us 48us
100.100.61.88 17 11 276m -0.001 0.009 -389us 39us
列名 | 含义 |
---|---|
Name/IP address | 表示源的名称或IP地址,或者参考时钟的refid值 |
NP | 这是当前为服务器保留的采样点数,通过这些点执行线性回归方法来估算出偏移值 |
9us 35us
100.100.5.3 21 11 344m +0.001 0.006 +80us 48us
100.100.61.88 17 11 276m -0.001 0.009 -389us 39us
| 列名 | 含义 |
| --- | --- |
| Name/IP address | 表示源的名称或IP地址,或者参考时钟的refid值 |
| NP | 这是当前为服务器保留的采样点数,通过这些点执行线性回归方法来估算出偏移值 |
[外链图片转存中...(img-WJNzuxmw-1727248514732)]
[外链图片转存中...(img-sozEjHiv-1727248514732)]
[外链图片转存中...(img-qBbD3lld-1727248514733)]
**既有适合小白学习的零基础资料,也有适合3年以上经验的小伙伴深入学习提升的进阶课程,涵盖了95%以上运维知识点,真正体系化!**