安装Oracle 10g 的正在检查网络配置需求,未执行

在安装oracle 10g时，在先行条件检测时会出现 
　　　　“正在检查网络配置需求...检查完成。此次检查的总体结果为: 未执行 <<<< 
　　解决方案: Oracle 支持在具有 DHCP 分配的 IP 地址的系统上进行安装。但在安装之前, 必须将 Microsoft LoopBack Adapter 配置为系统的主网络适配器。有关在配置有 DHCP 的系统上安装软件的详细信息, 请参阅 Installation Guide。” 
　　解决方法： 
　　　　在安装ORACLE 10g前系统会检测安装的一些前提条件是否满足，往往会提示说：将Microsoft LoopBack Adapter配置为系统的主网络适配器。 
　　　　如果你没有这样配置，且你不希望安装过程由于这个而出现问题，那么可以按如下过程操作： 

　　　　控制面板->添加硬件，在向导中选择“是，已经连接了此硬件”→添加新硬件设备→安装我手动列表选择硬件(高级)→网络适配器→厂商：Microsoft 网卡：Microsoft Loopback Adapter，添加完成，你会发现新建了个“本地连接”，用的就是这个假的“Microsoft Loopback Adapter”（因为根本就没有连接这个硬件，只是骗下Oracle而已）。把这个本地连接的IP设置一下（例如192.168.0.1）。好了，现在回去重新让Oracle检测一遍吧，应该通过了吧。

本文地址http://blog.tianya.cn/blogger/post_show.asp?BlogID=450994&PostID=12894290

win7下找到添加硬件在设备管理器 ---操作 -- 添加过时硬件 

 

During Oracle installation on a windows machine that is configured to use DHCP in order to obtain its IP address, the Following message will probably be displayed:

Checking Network Configuration requirements …
Check complete. The overall result of this check is: Failed <<<<
Problem: The install has detected that the primary IP address of the system is DHCP-assigned.
Recommendation: Oracle supports installations on systems with DHCP-assigned IP addresses; However, before you can do this, you must configure the Microsoft LoopBack Adapter to be the primary network adapter on the system.  See the Installation Guide for more details on installing the software on systems configured with DHCP.

As the error message say, this due to the fact that you are trying to install Oracle on a machine that is using DHCP to obtain its IP address. You can still install oracle on a machine without a constant IP address. All you need to do is configure the LoopBack adapter:

Install the Loopback adapter
1)     Go to the control panel and choose add hardware
2)    The Add Hardware wizard will be displayed, click Next
3)    Choose “Yes, I have already connected the hardware” and click Next
4)    An hardware list will be displayed. Navigate to the bottom of the list and choose “Add new hardware       device”
5)    Choose Install the hardware that I manually select from a list (Advance)”
6)    Choose “Network adapter”
7)    Choose “Microsoft” on the left side of the window and “Microsoft Loopback Adapter” on the right             window”
8)    Click Next and verify that Microsoft Loopback Adapter is about to install and click next again and       finish.

Configure the loop back adapter
1)    Go to control panel – network connections, you will see a new network connection.
2)    Choose “local area connection 2” (the name may vary but basically it is the one we just added) and       click properties.
3)    Click on tcp/ip and then properties.
4)    Enter an IP address and a subnet mask (you can use 1.1.1.2 and subnet 255.255.255.0)

Go to network connection and click on Advanced settings under the Advanced menu and verify that the loopback adapter is in the first one. (Update: it look like this step is optional because it seems to work in most cases anyway)

Now you can continue your oracle installation.