The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL toRestarting system.
U-Boot 2010.06 (Nov 15 2012 - 13:33:07)
DRAM: 256 MiB
NAND: Special Nand id table Version 1.35
Nand ID: 0xEC 0xF1 0x00 0x95 0x40 0xEC 0xF1 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:1bit
128 MiB
Check spi flash controller v300. found
Spi(cs1) ID: 0x20 0x20 0x18 0x00 0x00 0x00
Spi(cs1): Block:256KB Chip:16MB Name:"M25P128"
In: serial
Out: serial
Err: serial
judge ddr init
user init finish.
Hit any key to stop autoboot: 0
16384 KiB hi_sfc at 0:0 is now current device
## Booting kernel from Legacy Image at 82000000 ...
Image Name: Linux-3.0.8
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3497060 Bytes = 3.3 MiB
Load Address: 80008000
Entry Point: 80008000
Loading Kernel Image ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 3.0.8 (pub@BVT-SDK-SERVER3) (gcc version 4.4.1 (Hisilicon_v200(gcc4.4-290+glibc-2.11+eabi+nptl)) ) #1 SMP Tue Jun 4 17:13:30 CST 2013
CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c53c7f
CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
Machine: godnet
Memory policy: ECC disabled, Data cache writealloc
PERCPU: Embedded 7 pages/cpu @c0741000 s5152 r8192 d15328 u32768
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock2 rootfstype=jffs2 mtdparts=hi_sfc:1M(boot),4M(kernel),11M(rootfs);hinand:128M(nand)
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 57992k/57992k available, 7544k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc4800000 - 0xfe000000 ( 920 MB)
lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0036000 ( 184 kB)
.text : 0xc0036000 - 0xc063a000 (6160 kB)
.data : 0xc063a000 - 0xc06611e0 ( 157 kB)
.bss : 0xc0661204 - 0xc06bd934 ( 370 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:128 nr_irqs:128 128
sched_clock: 32 bits at 155MHz, resolution 6ns, wraps every 27709ms
Console: colour dummy device 80x30
Calibrating delay loop... 1849.75 BogoMIPS (lpj=9248768)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
CPU1: Booted secondary processor
Brought up 2 CPUs
SMP: Total of 2 processors activated (3706.06 BogoMIPS).
NET: Registered protocol family 16
Serial: AMBA PL011 UART driver
uart:0: ttyAMA0 at MMIO 0x20080000 (irq = 40) is a PL011 rev2
console [ttyAMA0] enabled
uart:1: ttyAMA1 at MMIO 0x20090000 (irq = 41) is a PL011 rev2
bio: create slab <bio-0> at 0
controller0, config base:0x20800000, mem size:0x800000
controller1, config base:0x20810000, mem size:0x800000
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
PCI: bus2: Fast back to back transfers disabled
PCI: bus3: Fast back to back transfers enabled
pci 0000:02:00.0: BAR 0: assigned [mem 0x60000000-0x607fffff pref]
pci 0000:02:00.0: BAR 0: set to [mem 0x60000000-0x607fffff pref] (PCI address [0x60000000-0x607fffff])
pci 0000:02:00.0: BAR 1: assigned [mem 0x60800000-0x6080ffff]
pci 0000:02:00.0: BAR 1: set to [mem 0x60800000-0x6080ffff] (PCI address [0x60800000-0x6080ffff])
pci 0000:02:00.0: BAR 6: assigned [mem 0x60810000-0x6081ffff pref]
pci 0000:02:00.0: PCI bridge to [bus 03-03]
pci 0000:02:00.0: bridge window [io disabled]
pci 0000:02:00.0: bridge window [mem disabled]
pci 0000:02:00.0: bridge window [mem pref disabled]
pci 0000:00:00.0: BAR 0: assigned [mem 0x30000000-0x307fffff pref]
pci 0000:00:00.0: BAR 0: set to [mem 0x30000000-0x307fffff pref] (PCI address [0x30000000-0x307fffff])
pci 0000:00:00.0: BAR 1: assigned [mem 0x30800000-0x3080ffff]
pci 0000:00:00.0: BAR 1: set to [mem 0x30800000-0x3080ffff] (PCI address [0x30800000-0x3080ffff])
pci 0000:00:00.0: BAR 6: assigned [mem 0x30810000-0x3081ffff pref]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0: bridge window [io disabled]
pci 0000:00:00.0: bridge window [mem disabled]
pci 0000:00:00.0: bridge window [mem pref disabled]
vgaarb: loaded
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource timer1
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 128 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 128 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered named UNIX socket transport module.
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
L2cache cache controller enabled
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
fuse init (API version 7.16)
SGI XFS with security attributes, large block/inode numbers, no debug enabled
msgmni has been set to 113
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler deadline registered (default)
io scheduler cfq registered
brd: module loaded
loop: module loaded
ahci: SSS flag set, parallel bus scan disabled
ahci ahci.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl platform mode
ahci ahci.0: flags: ncq sntf stag pm led clo only pmp pio slum part ccc sxs boh
scsi0 : ahci_platform
scsi1 : ahci_platform
ata1: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x100 irq 68
ata2: SATA max UDMA/133 mmio [mem 0x10080000-0x1008ffff] port 0x180 irq 68
Spi id table Version 1.22
Hisilicon Spi Flash Controller V300 New Device Driver, Version 1.10
Check Spi Flash Controller V300 New.
Found
Spi(cs1) ID: 0x20 0x20 0x18 0x00 0x00 0x00
Spi(cs1):
Block:256KB
Chip:16MB
Name:"M25P128"
spi size: 0x16777216
chip num: 1
3 cmdlinepart partitions found on MTD device hi_sfc
Creating 3 MTD partitions on "hi_sfc":
0x000000000000-0x000000100000 : "boot"
0x000000100000-0x000000500000 : "kernel"
0x000000500000-0x000001000000 : "rootfs"
Special nand id table Version 1.35
Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
Nand ID: 0xEC 0xF1 0x00 0x95 0x40 0xEC 0xF1 0x00
Nand(Hardware): Block:128KB Page:2KB Chip:128MB OOB:64B ECC:1bit
NAND device: Manufacturer ID: 0xec, Chip ID: 0xf1 (Samsung NAND 128MiB 3,3V 8-bit)
1 cmdlinepart partitions found on MTD device hinand
Creating 1 MTD partitions on "hinand":
0x000000000000-0x000008000000 : "nand"
Fixed MDIO Bus: probed
sky2: driver version 1.28
usbcore: registered new interface driver rt2500usb
usbcore: registered new interface driver rt73usb
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
hiusb-ehci hiusb-ehci.0: HIUSB EHCI
hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
hiusb-ehci hiusb-ehci.0: irq 63, io mem 0x100b0000
hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ata1: SATA link down (SStatus 0 SControl 300)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
hiusb-ohci hiusb-ohci.0: HIUSB OHCI
hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
hiusb-ohci hiusb-ohci.0: irq 64, io mem 0x100a0000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver cdc_wdm
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver mdc800
mdc800: v0.7.5 (30/10/2000):USB Driver for Mustek MDC800 Digital Camera
mousedev: PS/2 mouse device common for all mice
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
lib80211: common routines for IEEE802.11 drivers
Registering the dns_resolver key type
VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
registered taskstats version 1
ata2: SATA link down (SStatus 0 SControl 300)
VFS: Mounted root (jffs2 filesystem) on device 31:2.
Freeing init memory: 184K
_ _ _ _ _ _ _ _ _ _ _ _
\ _ _ _ _ _ ___
/ /__/ \ |_/
/ __ / - _ ___
/ / / / / /
_ _ _ _/ / / \_/ \_ ______
___________\___\__________________
[RCS]: /etc/init.d/S00devs
[RCS]: /etc/init.d/S01udev
udevd[568]: mainudevd (568): /proc/568/oom_adj is deprecated, please use /proc/568/oom_score_adj instead.
: error opening /dev/null: No such file or directory
[RCS]: /etc/init.d/S80network
[RCS]: /etc/init.d/S81toe
STMMAC driver:
platform registration...
done!
Set system config register 0x200300ec with value 0x003f003f
done!
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x36
Enhanced descriptor structure
MACADDR in get is 0:0:0:0:0:0
no valid MAC address for MAC 0;please, use ifconfig or nwhwconfig!
eth0 - (dev. name: stmmaceth - id: 0, IRQ #119
IO base addr: 0xc4980000)
STMMAC MII Bus: probed
eth0: PHY ID 001cc915 at 0 IRQ 0 (1:00)
eth0: PHY ID 001cc915 at 1 IRQ -6 (1:01) active
eth0: PHY ID 001cc915 at 2 IRQ 0 (1:02)
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x36
Enhanced descriptor structure
MACADDR in get is 0:0:0:0:0:0
no valid MAC address for MAC 1;please, use ifconfig or nwhwconfig!
eth1 - (dev. name: stmmaceth - id: 0, IRQ #119
IO base addr: 0xc4984000)
eth1: PHY ID 001cc915 at 0 IRQ 0 (1:00)
eth1: PHY ID 001cc915 at 1 IRQ -6 (1:01)
eth1: PHY ID 001cc915 at 2 IRQ 0 (1:02) active
stmmac_reset: RESET COMPLETE!
**************************************************
* TNK driver built on Jun 4 2013 at 17:13:17
* TNK driver mode is BYPASS
**************************************************
stmmac: Rx Checksum Offload Engine supported
stmmac: Rx Checksum Offload Engine supported
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200F0234: 0x00000000 --> 0x00000000
[END]
*** Board tools : ver0.0.1_20121120 ***
eth0: generated random MAC address 4e:e8:01:83:a5:93
0x200F0238: 0x0MACADDR in set is 4e:e8:1:83:a5:93
0000001 --> 0x00000000
[END]
*** Board tools eth1: generated random MAC address 7e:f9:24:d1:61:8c
: ver0.0.1_20121MACADDR in set is 7e:f9:24:d1:61:8c
120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200F023C: 0x00000000 --> 0x000000yaffs: dev is 32505859 name is "mtdblock3" rw
00
[END]
*** yaffs: passed flags ""
Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x200F0240: 0x00000001 --> 0x00000000
[END]
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20260400: 0x00000000 --> 0x00000020
[END]
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20260080: 0x00000000 --> 0x00000020
[END]
*** Board tools : ver0.0.1_20121120 ***
[debug]: {source/utils/cmdshell.c:166}cmdstr:himm
0x20260080: 0x00000020 --> 0x00000000
[END]
SDK_TYPE type is 4hd
Hisilicon Media Memory Zone Manager
hi3531_base: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Hisilicon UMAP device driver interface: v3.00
load sys.ko for Hi3531...OK!
Load tde.ko ...OK!
load venc.ko for Hi3531...OK!
load group.ko for Hi3531...OK!
card disconnected!
load chnl.ko for Hi3531...OK!
load h264e.ko for Hi3531...OK!
load rc.ko for Hi3531...OK!
load jpege.ko for Hi3531...OK!
load mpeg4e.ko for Hi3531...OK!
load viu.ko for Hi3531...OK!
load vou.ko ....OK!
load vpss.ko ....OK!
load region.ko ....OK!
load vda.ko ....OK!
load vdec.ko ....OK
load vhd firmware.ko OK
load hdmi.ko ....OK!
Load jpeg6b.ko success. (SDK_VERSION:[jpeg6bv1.0] Build Time:[Jun 4 2013, 17:14:53])
Kernel: ssp initial ok!
read secs=21, mins=30, hours=13, mday=1, mon=0, year=100, wday=0
Auto login as root ...
login[889]: root login on 'ttyS000'
Welcome to HiLinux.
None of nfsroot found in cmdline.
# PHY: 1:01 - Link is Up - 1000/Full