CCNA3.0TK答案错误更正(转)

CCNA3.0TK答案错误更正(转)[@more@]

　　QUESTION NO: 18

　　What can you use to connect a user’s pc directly to a router?

　　A. Connect the PC's COM port to the router's console port using a

　　straight-through cable.

　　B. Connect the PC's COM port to the router's console port using a

　　crossover cable.

　　C. Connect the PC's COM port to the router's Ethernet port using a

　　straight-through cable.

　　D. Connect the PC's Ethernet port to the router's Ethernet port

　　using a crossover cable.

　　E. Connect the PC's Ethernet port to the router's Ethernet port

　　using a rollover cable.

　　F. Connect the PC's Ethernet port to the router's Ethernet port

　　using a straight-through cable.

　　Answer: D.

　　***the answer D is correct,but lots of people confuse about the

　　cable***

　　straight-through calbe and crossover cable are used to connect LAN

　　interfaces!

　　when we connect pc-to-pc router-to-router pc-to-router

　　switch-to-switch ... use crossover cable

　　when we connect pc-to-switch router-to-switch ...use

　　straight-through cable

　　the rollover calbe can be used to connect console port and the PC's

　　COM port.

　　这道题主要看题干，如果是useto console而不是connect就选B

　　QUESTION NO: 75

　　Consider Frame Relay multipoint subinterfaces. Which is a valid

　　statement?

　　A. An IP address is required on the physical interface of the

　　central router.

　　B. All routers are required to be fully meshed.

　　C. All routers must be in the same subnet to forward routing updates

　　and broadcasts.

　　D. Multipoint is the default configuration for Frame Relay

　　subinterfaces.

　　Answer: D

　　***the correct answer should be C***

　　Sybex study guide CCNA 3.0 page 522:

　　Multipoint Used when the router is the center of a star of virtual

　　circuits. Uses a single

　　subnet for all routers’ serial interfaces connected to the frame

　　switch.

　　Introduction to Cisco Rouer Configuration page 413:

　　You must specify either multipoint or point-to-point; there is no

　　default.

　　这道题TK确实是错了

　　QUESTION NO: 79

　　Answer Lab 3:

　　enable

　　config terminal

　　640 - 607

　　hostname Plain

　　enable secret TestKing

　　interface ethernet 0

　　ip address 192.168.65.1 255.255.255.0

　　no shutdown

　　exit

　　interface serial1

　　ip address 192.168.101.2 255.255.255.0

　　no shutdown

　　exit

　　router rip

　　network 192.168.65.0

　　network 192.168.101.0

　　network 192.168.55.0

　　network 192.168.149.0

　　network 192.168.199.0

　　^z

　　copy running-config startup-config

　　***the correct answer should be ***

　　enable

　　config terminal

　　640 - 607

　　hostname Plain

　　enable secret TestKing

　　interface ethernet 0

　　ip address 192.168.65.1 255.255.255.0

　　no shutdown

　　exit

　　interface serial1

　　ip address 192.168.101.2 255.255.255.0

　　no shutdown

　　exit

　　router rip

　　network 192.168.65.0

　　network 192.168.101.0

　　^z

　　copy running-config startup-config

　　***We need not add other three networks***

　　Ciscopress CCNA Exam 640-607 Certification Guide page 431:

　　The network command “matches” one or more interfaces on a router.

　　For each interface,

　　the network command causes the router to do three things:

　　1 The router broadcasts or multicasts routing updates out an

　　interface.

　　2 The router listens for incoming updates on that same interface.

　　3 The router, when sending an update, includes the subnet of that

　　interface in the

　　routing update.

　　QUESTION NO: 109

　　Julia telnets to a pc on a remote subnet, which MAC address will be

　　present in the ARP table when you

　　issue the show arp command?

　　A. MAC address of the destination host Ethernet port.

　　B. MAC address of the local router Ethernet port.

　　C. MAC address of the destination router Serial port.

　　D. MAC address of the local router Serial Port.

　　Answer: A

　　***the correct answer should be B***

　　the pc transfort the packets to local router, and the router find

　　the best way to remote network, so we

　　choose the answer B!

　　QUESTION NO: 133

　　You have a direct serial link to an adjacent router. You do not have

　　connectivity, and when you run the

　　show running-config the output says that the serial interface is

　　shutdown.

　　You issue the command: show interface s0

　　What will the output include?

　　A. Serial 0 is up, line protocol is down.

　　B. Serial 0 is down, line protocol is down.

　　C. Serial 0 is down, line protocol is up.

　　D. Serial is administratively down, line protocol is down.

　　E. Serial 0 is administratively down, line protocol is up.

　　F. Serial 0 is administratively up, line protocol is down.

　　Answer: B

　　***the correct answer should be D***

　　I had tried it on boson router sim. Only you issued the command

　　"shutdown" on an interface the running-config

　　would say that the interface was "shutdown". Remember that the

　　running-config just display our setting not the real status

　　of the router! Because we had made the interface shutdown, the show

　　interface s0 command would say that the interface was

　　administratively

　　down!

　　QUESTION NO: 145

　　You need to find out the IPX address on a Cisco 2500 series router.

　　Which command displays all routed

　　protocols and the interfaces on which the protocol is enabled?

　　A. Show protocols.

　　B. Show protocol brief.

　　C. Show interfaces protocol.

　　D. Show interfaces.

　　E. Show routed.

　　F. Show routed interfaces.

　　Answer: D

　　***the correct answer should be A***

　　the "show interfaces" command outputs ip protocol only!

　　QUESTION NO: 202

　　You are configuring R3 so that it can communicate with R2 on

　　Ethernet port e1. What encapsulation

　　should you use on s0 to setup this IPX network?

　　A. SAP

　　B. HDLC

　　C. ARPA

　　D. Novell-Ether

　　Answer: D

　　Explanation: In order for both routers to communicate they must be

　　using the same type of encapsulation.

　　Therefore e1 of router R3 must have novell-ether encapsulation.

　　***the answer is correct but the question should be:

　　You are configuring R3 so that it can communicate with R2 on

　　Ethernet port e1. What encapsulation

　　should you use on e1 to setup this IPX network?

　　QUESTION NO: 274

　　What are two commands that you can use to view your access lists?

　　(Choose two)

　　A. Show filters.

　　B. Show access-lists.

　　C. Show IP access-list.

　　D. Show running-Config.

　　Answer: B, C

　　***the correct answer should be B,D***

　　The command "show running-config" do output the contents of all

　　access-lists, on the other hand the "show ip access-list" command

　　can not output the ipx access-list!

　　It is too bad I could not issue the "show ip access-list" command on

　　boson sim software!

　　QUESTION NO: 291

　　Which of the following are true about layer 3 of the OSI model?

　　(Choose four)

　　A. It uses a two-part address.

　　B. It maintains routing tables.

　　C. It uses broadcast addresses.

　　D. It establishes network addresses.

　　E. It provides access to the LAN media.

　　F. It provides media independence for upper layers.

　　G. It provides path selection for Internet work communicati

来自 “ ITPUB博客 ” ，链接：http://blog.itpub.net/8225414/viewspace-951881/，如需转载，请注明出处，否则将追究法律责任。

转载于:http://blog.itpub.net/8225414/viewspace-951881/