How to Proceed from Failed 11gR2 Grid Infrastructure (CRS) Installation [ID 942166.1] | |||||
| |||||
修改时间 16-FEB-2011 类型 HOWTO 状态 PUBLISHED |
In this Document
Goal
Solution
Deconfigure and Reconfigure of Standalone Server (Oracle Restart):
Deinstall of Grid Infrastructure Standalone Server:
Deconfigure and Reconfigure of Grid Infrastructure Cluster:
Deinstall of Grid Infrastructure Cluster:
Complete Configuration Assistant if OUI is Closed:
References
Applies to:
Oracle Server - Enterprise Edition - Version: 11.2.0.1 to 11.2.0.2 - Release: 11.2 to 11.2Generic UNIX
Generic Linux
Goal
This goal of this note is to provide steps to proceed from failed 11gR2 Grid Infrastructure installation.
Similar procedure for 10gR1, 10gR2 or 11gR1 available in note 239998.1 and note 399482.1
Solution
Deconfigure and Reconfigure of Standalone Server (Oracle Restart):
To deconfigure:
As root, execute "$GRID_HOME/crs/install/roothas.pl -deconfig -force -verbose"
If it fails, please disable CRS, reboot the node and try the same command:
As root, reboot the node; once the node comes backup, execute above deconfigure command again.
To reconfigure:
As root, execute "$GRID_HOME/root.sh"
Deinstall of Grid Infrastructure Standalone Server:
As grid user, execute $GRID_HOME/deinstall/deinstall
Deconfigure and Reconfigure of Grid Infrastructure Cluster:
Identify cause of root.sh failure by reviewing logs in $GRID_HOME/cfgtoollogs/crsconfig and $GRID_HOME/log, once cause is identified, deconfigure and reconfigure with steps below - please keep in mind that you will need wait till each step finishes successfully before move to next one:
Step 0: For 11.2.0.2 and above, root.sh is restartable. Once cause is identified and fixed, root.sh can be executed again on the failed node, if it succeeds, you can continue with the installation, otherwise proceed to next step (Step 1) of the note.
Step 1: As root, run "$GRID_HOME/crs/install/rootcrs.pl -verbose -deconfig -force" on all nodes, except the last one.
Step 2: As root, run "$GRID_HOME/crs/install/rootcrs.pl -verbose -deconfig -force -lastnode" on last node. This command will zero out OCR and VD disk also.
Note:
A. Step1 and 2 can be skipped on node(s) where root.sh haven't been execute.
B. Step1 and 2 should remove checkpoint file. To verify:
ls -l $ORACLE_BASE/Clusterware/ckptGridHA_.xml
If it's still there, please remove it manually with "rm" command on all nodes
C. If GPNP profile is different between nodes/setup, clean it up on all nodes as grid user
$ rm -rf $GRID_HOME/gpnp/*
$ mkdir -p $GRID_HOME/gpnp/profiles/peer $GRID_HOME /gpnp/wallets/peer $GRID_HOME /gpnp/wallets/prdr $GRID_HOME /gpnp/wallets/pa $GRID_HOME /gpnp/wallets/root
The profile needs to be cleaned up:
C1. If root.sh is executed concurrently - one should not execute root.sh on any other nodes before it finishes on first node.
C2. If network info, location of OCR or Voting Disk etc changed after Grid is installed.
Step 3: As root, run $GRID_HOME/root.sh on first node
Step 4: As root, run $GRID_HOME/root.sh on all other node(s), except last one.
Deinstall of Grid Infrastructure Cluster:
Case 1: "root.sh" never ran on this cluster, then as grid user, execute $GRID_HOME/deinstall/deinstall
Case 2: "root.sh" already ran, then follow the step below - please keep in mind that you will need wait till each step finishes successfully before move to next one:
Step 1: As root, run "$GRID_HOME/crs/install/rootcrs.pl -verbose -deconfig -force" on all node, except the last one.
Step 2: As root, run "$GRID_HOME/crs/install/rootcrs.pl -verbose -deconfig -force -lastnode" on last node. This command will zero out OCR and VD disk also.
Step 3: As grid user, run "$GRID_HOME/deinstall/deinstall" on any node.
Complete Configuration Assistant if OUI is Closed:
If $GRID_HOME/cfgtoollogs/configToolAllCommands doesn't exist, create a shell script. with the following content:/ocw/grid/oui/bin/runConfig.sh ORACLE_HOME=/ocw/grid MODE=perform. ACTION=configure RERUN=true $*
If any configuration assistants already finished successfully previously and you'd like to skip them, please be sure to set RERUN to false, for example:
As grid user, execute $GRID_HOME/cfgtoollogs/configToolAllCommands on first node.
References
NOTE:1050908.1 - How to Troubleshoot Grid Infrastructure Startup IssuesNOTE:1054902.1 - How to Validate Network and Name Resolution Setup for the Clusterware and RAC
NOTE:1056322.1 - How to Troubleshoot 11gR2 Installation Issue
NOTE:239998.1 - How to Clean Up After a Failed 10g or 11.1 Oracle Clusterware Installation
NOTE:399482.1 - How to Recreate OCR/Voting Disk Accidentally Deleted
NOTE:969254.1 - How to Proceed from Failed Upgrade to 11gR2 Grid Infrastructure (CRS)
来自 “ ITPUB博客 ” ,链接:http://blog.itpub.net/611609/viewspace-692171/,如需转载,请注明出处,否则将追究法律责任。
转载于:http://blog.itpub.net/611609/viewspace-692171/