myself reedit for 2440gdbinit file



# 
     
    # J-LINK GDB SERVER initialization 
     
    # 
     
    # This connects to a GDB Server listening 
     
    # for commands on localhost at tcp port 2331 
     
    target remote 192.168.1.105:2331 #首先连接主机的GDB Server，端口都是2331。 
     
    #注意主机的GDB Server勾掉"Localhost only"选项，否则连接不上 
     
    # Set JTAG speed to 30 kHz 
     
    monitor speed 30 
     
      
     
    # Set GDBServer to little endian 
     
    monitor endian little 
     
      
    #end 
     
    # Reset the chip to get to a known state. 
     
    monitor reset 
     
      
     
    # 
     
    # CPU core initialization 
     
    # 
     
      
     
    # Set the processor mode 
     
    monitor reg cpsr = 0xd3 
     
      
     
    #disable watchdog 
     
    monitor MemU32 0x53000000 = 0x00000000 
     
      
     
    #disable interrupt 
     
    monitor MemU32 0x4A000008 = 0xFFFFFFFF #INTMSK 
     
    monitor MemU32 0x4A00000C = 0x00007FFF #INTSUBMSK 
     
      
     
    #set clock 
     
    monitor MemU32 0x4C000000 = 0x00FFFFFF 
     
    monitor MemU32 0x4C000014 = 0x00000005 
     
    monitor MemU32 0x4C000004 = 0x0005C011 
     
      
     
    #config sdram 
     
    monitor MemU32 0x48000000 = 0x22011110 #conw 
     
    monitor MemU32 0x48000004 = 0x00000700 #bank0 
     
    monitor MemU32 0x48000008 = 0x00000700 #bank1 
     
    monitor MemU32 0x4800000C = 0x00000700 #bank2 
     
    monitor MemU32 0x48000010 = 0x00000700 #bank3 
     
    monitor MemU32 0x48000014 = 0x00000700 #bank4 
     
    monitor MemU32 0x48000018 = 0x00000700 #bank5 
     
    monitor MemU32 0x4800001C = 0x00018005 #bank6 
     
    monitor MemU32 0x48000020 = 0x00018005 #bank7 
     
    monitor MemU32 0x48000024 = 0x008E04F4 #vREFRESH 
     
    monitor MemU32 0x48000028 = 0xB1 #vBANKSIZE -- 128M/128M --- should 
     
    monitor MemU32 0x4800002c = 0x30 #vMRSRB6 
     
    monitor MemU32 0x48000030 = 0x30 #vMRSRB7 
     
      
     
    # Set auto JTAG speed 
     
    monitor speed auto 
     
      
     
    # Setup GDB FOR FASTER DOWNLOADS 
     
    set remote memory-write-packet-size 1024 
     
    set remote memory-write-packet-size fixed 
     
      
     
    # Load the program executable called "image.elf" 
     
    # load image.elf 
     
    b _start 
     
    load 
    #/home/uboot/workspace/uboot1/u-boot
     
    continue