AP6255 蓝牙驱动移植

1：平台 imx6

2：蓝牙模块为AP6255

原理图部分：

配置UART4

static iomux_v3_cfg_t mx6sl_uart4_pads[] = {
MX6SL_PAD_KEY_COL6__UART4_RXD,
MX6SL_PAD_KEY_COL7__UART4_RTS,
MX6SL_PAD_KEY_ROW6__UART4_TXD,
MX6SL_PAD_KEY_ROW7__UART4_CTS,

};

然后make menuconfig

CONFIG_BT=y

CONFIG_BT_RFCOMM=y

CONFIG_BT_RFCOMM_TTY=y

CONFIG_BT_BNEP=y

CONFIG_BT_BNEP_MC_FILTER=y

CONFIG_BT_BNEP_PROTO_FILTER=y

CONFIG_BT_HIDP=y

CONFIG_BT_HCIBTUSB=y

CONFIG_BT_HCIUART=y

CONFIG_BT_HCIUART_H4=y

配置

#define MX6_BRD_FEC_BT_REG_ON IMX_GPIO_NR(3, 25)

根据蓝牙模块的上电时序，上电

3：主要修改hal层：

hardware\broadcom\libbt\conf\AP6255：

 

bd_addr.txt 11:22:33:44:55:66

bt_vendor.conf:

# UART device port where Bluetooth controller is attached
UartPort = /dev/ttymxc3
# Firmware patch file location
FwPatchFilePath = /system/etc/firmware/
#
# #Firmware name
FwPatchFileName = BCM4345C0.hcd

#

使用第4个串口，为/dev/ttymxc3， 固件位置FwPatchFilePath = /system/etc/firmware/

固件名字：FwPatchFileName = BCM4345C0.hcd

Android.mk

LOCAL_PATH := $(call my-dir)
include $(CLEAR_VARS)
LOCAL_MODULE := bt_vendor.conf
LOCAL_MODULE_CLASS := ETC
LOCAL_MODULE_PATH := $(TARGET_OUT)/etc/bluetooth
LOCAL_MODULE_TAGS := eng
LOCAL_SRC_FILES := $(LOCAL_MODULE)

include $(BUILD_PREBUILT)

配置：BoardConfig.mk

BOARD_HAVE_BLUETOOTH:True

BOARD_HAVE_BLUETOOTH_BCM:True

修改:hardware/broadcom/libbt/include/bt_vendor_brcm.h

UART_TARGET_BAUD_RATE 3000000

LPM_SLEEP_MODE     0

4:rfkill 主要控制蓝牙的上电与下电

static struct platform_device mxc_bt_rfkill = {
.name = "mxc_bt_rfkill",
};


static struct imx_bt_rfkill_platform_data mxc_bt_rfkill_data = {
.power_change = mx6sl_evk_bt_power_change,
};

mxc_register_device(&mxc_bt_rfkill, &mxc_bt_rfkill_data);

static struct platform_driver mxc_bt_rfkill_driver = {
.driver = {
.name = "mxc_bt_rfkill",
},
.probe = mxc_bt_rfkill_probe,
.remove = __devexit_p(mxc_bt_rfkill_remove),

};

static int mxc_bt_set_block(void *rfkdata, bool blocked)
{
struct imx_bt_rfkill_platform_data *data = rfkdata;
int ret;


/* Bluetooth stack will reset the bluetooth chip during
* resume, since we keep bluetooth's power during suspend,
* don't let rfkill to actually reset the chip. */
if (system_in_suspend)
return 0;
pr_info("rfkill: BT RF going to : %s\n", blocked ? "off" : "on");
if (!blocked)
ret = data->power_change(1);
else
ret = data->power_change(0);


return ret;
}


static const struct rfkill_ops mxc_bt_rfkill_ops = {
.set_block = mxc_bt_set_block,

};

通过power_change，打开关闭蓝牙

int mx6sl_evk_bt_power_change(int status)
{
if (status)
mx6sl_evk_bt_reset();
else
mx6sl_evk_bt_off();
return 0;

}

操作gpio实现，上电与下电。