Sun Fire™ V490 RSC配置说明

与V240不同的是，Sun Fire™ V480, V880, V490, and V890 SC使用的不是ALOM而是RSC，RSC的配置可以在正常状态#下完成，并不需要借助console口！rsc的配置软件不是系统默认安装的，首先要在服务器上安装rsc的软件包Sun Remote System Control (RSC) 2.2.3 Software，可以在sun的补丁光盘里面找到，位于光盘的目录：sun/progs/RSC/2.2.3中。该软件包也可以从sun的网站上下载，如下是参考链接地址：

http://www.sun.com/servers/rsc.html

在solaris 8上软件包是rsc2.2.3_packages_s8.zip，solaris 9和solaris 10使用同样的软件包是rsc2.2.3_packages_s8.zip

该软件安装步骤如下：

先准备软件包，然后解压缩，

# unzip rsc2.2.3_packages_s8.zip

解压缩后出现很多的软件包，如下：

README SUNWfrscd SUNWkrscd

README-RSC SUNWfrscj SUNWkrscj

SUNWcrsc SUNWhrsc SUNWrsc

SUNWcrscd SUNWhrscd SUNWrscd

SUNWcrscj SUNWhrscj SUNWrscj

SUNWdersc SUNWirscd SUNWsrscd

SUNWdrscd SUNWirscj SUNWsrscj

SUNWdrscj SUNWitrsc SUNWsvrsc

SUNWerscd SUNWjersc en_us_relnotes.pdf

SUNWerscj SUNWjrscd rsc2.2.3_packages_s8.zip

SUNWesrsc SUNWjrscj rsc2.2.3_packages_s9.zip

SUNWfrrsc SUNWkrsc软件包中是针对不同语言环境不同的软件包，英文的软件包是必须安装的，中文的软件包是
SUNWcrsc SUNWcrscd SUNWcrscj

英文的软件包是：
SUNWrsc SUNWrscd SUNWrscj

除了中文和英文的软件包外把多余的软件包删除掉，剩下如下软件包：

README SUNWcrscj en_us_relnotes.pdf

README-RSC SUNWrsc rsc2.2.3_packages_s8.zip

SUNWcrsc SUNWrscd rsc2.2.3_packages_s9.zip

SUNWcrscd SUNWrscj

然后安装这些软件包。

# pkgadd -d .

安装完之后，会在/usr/platform/`uname -i`/ 路径下生成rsc目录

# cd /usr/platform/`uname -i`/rsc

# ./ rsc-initscript

# ./rsc-config

 

Continue with RSC setup (y|n): y

Set RSC date/time now (y|n|?) [y]: 
Server Hostname [SUN280R]: 
Edit customer info field (y|n|?) [n]: 
Enable RSC Ethernet Interface (y|n|s|?) [n]: y
RSC IP Mode (config|dhcp|?) [dhcp]: n
RSC IP Mode (config|dhcp|?) [dhcp]: config
RSC IP Address []: 192.168.81.12
RSC IP Netmask [255.255.255.0]: 
RSC IP Gateway []: 192.168.81.254 
Enable RSC Alerts (y|n|s|?) [n]: 
Enable RSC Modem Interface (y|n|s|?) [n]: 
Enable RSC Serial Port Interface (y|n|s|?) [n]: 
Setup RSC User Account (y|n|?) [y]: 
Username []: admin
User Permissions (c,u,a,r|none|?) [cuar]: 



--------------------
Verifying Selections
--------------------


General Setup
-------------
Set RSC date now = y
Server Hostname = PMDB01

Set Customer Info = n

Is this correct (y|n): y



Ethernet Setup
--------------
IP Mode = config
IP Address = 192.168.81.12
IP Netmask = 255.255.255.0
IP Gateway = 192.168.81.254

Is this correct (y|n): y



Alert Setup
-----------
- Alerts disabled

Is this correct (y|n): y 



Modem Setup
-----------
- Modem disabled, ppp disabled

Is this correct (y|n): y



Serial Port Setup
-----------------
- Serial port disabled

Is this correct (y|n): y



User Setup
----------
User Name = neusoft
User Permissions = cuar

Is this correct (y|n): y


This script will now update RSC, continue? (y|n): y
Updating flash, this takes a few minutes
........................................
........................................
........................................
........................................
........................................
........................................
........................................
...........................
Download completed successfully

Resetting RSC (takes about 90 seconds): 
DONE
Setting up server to update RSC date on boot: DONE
Setting up server hostname: DONE
Setting up ethernet interface: DONE
Disabling RSC alert engine: DONE
Disabling modem interface: DONE
Disabling serial port interface: DONE
Adding user to RSC:
rscadm: user already exists
when this script completes,
use the rscadm command to correct the error.
Resetting RSC (takes about 90 seconds):
Are you sure you want to reboot RSC (y/n)? y


DONE
Setting up RSC date: DONE

*******************************
RSC has been successfully setup
*******************************

 

至此，配置完毕，可以使用telnet连接RSC了

与V240类似，系统也提供了rscadm命令用于在正常状态下管理配置rsc!不再赘述。

 

 

以下是RSC的基本操作：

在每次使用完成 RSC后一定要 logout ，以避免下次使用的异常(被占用了)
; |& g: P- d! c6 N" D. U
rsc>console  ------切换到主机操作系统中。在主机操作系统中退回到RSC远程控制端口使用组合键 ~ . 及英文的波浪号和句点，(先按Shift键 ~ , 后再按 . )，反复切换不会影响主机操作系统使用。rsc用户退出登录一定要用 logout 命令。& |4 x6 |2 [4 c% y# i$ A) O5 j

例：) M4 h6 o# z! E- W
rsc>console- T* R; T" u* E3 ?8 P6 _. B8 d6 i' Y
#5 ]% j! Y  B; ]+ x
# ~ . (组合键命令 ~ 和 . )$ |3 U" Y' p' S7 |9 l5 M
rsc>/ [* r: @# S4 s4 f
rsc>logout