图片插入:
首先得调用宏:
\usepackage{graphics}
一般在文章中插入图片的语句为:
\begin{figure}[htbp]
\centering
\includegraphics[width=0.75\textwidth]{figureName.eps}
\caption{FigureTitle}
\label{figure}
\end{figure}
在双栏下插入图片占据双栏时,加上两个*:
\begin{figure*}[htbp]
\centering
\includegraphics[width=0.75\textwidth]{figureName.eps}
\caption{FigureTitle}
\label{figure}
\end{figure*}
插入并列的子图时:\usepackage{subfigure}
\begin{figure}[htbp]
\centering
\subfigure[SubfigureTitle]{
\label{Fig.sub.1}
\includegraphics[width=0.75\textwidth]{figurename.eps}}
\subfigure[SubfigureTitle]{
\label{Fig.sub.2}
\includegraphics[width=0.75\textwidth]{figurename.eps}}
\caption{MainfigureTitleCaption}
\label{figure}
\end{figure}
对于语句中figure后的[htbp]说明:
这是个可选参数项,允许用户来指示图形有可能被放置的位置。这一可选参数项可以是下列字母的任意组合。
h here 当前位置;将图形放置在 正文文本中给出该图形环境的地方。如果本页所剩的页面不够, 这一参数将不起作用。
t top 顶部;将图形放置在页面的顶部。
b bottom 底部;将图形放置在页面的底部。
p page 浮动页;将图形放置在一只允许有浮动对象的页面上。
注:在使用这些参数时:
(1)如果在图形环境中没有给出上述任一参数,则缺省为 [tbp]。
(2)给出参数的顺序不会影响到最后的结果。因为在考虑这些参数时 LATEX 总是尝试以 h-t-b-p 的顺序来确定图形的位置。所以 [hb] 和 [bh] 都使 LaTex 以h-b 的顺序来排版。
(3)给出的参数越多,LATEX 的排版结果就会越好。[htbp], [tbp], [htp], [tp] 这些组合得到的效果不错。
指定图片大小:
\includegraphics[width=90mm,height=60mm]{figure.eps}
设定图片长宽,图片高度会自动缩放。
\includegraphics[width=\textwidth]{figure.eps}
设定图片宽度为文本宽度。
\includegraphics[width=0.75\textwidth]{figure.eps}
设定图片宽度为文本宽度的0.75倍
\includegraphics[scale=1]{figure.eps}
设定图片与原文件比例为1。
\includegraphics[angle=90]{figure.eps}
将图片旋转90度。
图片使用编译时得注意:
-- 在对.eps格式的图片进行编译时,得注意编译顺序,不能直接使用PDFLaTex,这样会出现编译错误说:Unknown graphics extension: .eps.而是得LaTex编译生成dvi->dvi2pdf或者LaTex编译生成dvi->dvi2ps->ps2pdf。
-- 在对.pdf或者.jpg格式的图片进行编译时,可以直接使用PDFLaTex。
label的使用:
标签使用语句:
\label{LabelName}
在需要引用该label时, ???
\label的使用注意事项:
\label{key}
A \label command appearing in ordinary text assigns to the key the number of the current sectional unit; one appearing inside a numbered environment assigns that number to the key.
A key can consist of any sequence of letters, digits, or punctuation characters. Upper- and lowercase letters are different.
The number assigned to the key can be accessed by use of the \ref command. For example,
\begin{equation}
....
\label{eq:no1}
\end{equation}
...
One can see from Eq.~( ??? ) that ...
In a table or figure environment, the \label command should follow the \caption command (or be part of its argument) since it is the \caption command which generates the number.