用U盘安装CentOS,如果使用默认的boot挂载,会将引导安装在U盘上,必须用U盘启动,遇到这种情况可以通过grub手动写入引导。(我在另一台服务器上安装时手动设置boot但是装好停留在Grub无法启动,这个没深入研究了,在这里就先说手动修改引导方法,给遇到同样问题的人参考,如有错误,欢迎拍砖)
进入grub
- [root@mfsmaster home]# /sbin/grub
找到grub的位置
- grub> find /grub/stage1
- (hd1,0)
如果提示Error 15: File not found,则尝试 find /boot/grub/stage1 或者 find stage1
(hd1,0)代表的第二个硬盘的第一个分区,相应的(hd0,0)代表的就是第一个硬盘第一个分区,这一步其实就是告诉我们引导被写入了U盘中= =
下面进入正题
我们将引导写入(hd0,0),即第一个磁盘第一个分区中,我在这里的系统盘是这个,具体可以在linux下用df指令查看
- grub> root (hd0,0)
- Filesystem type is ext2fs, partition type 0x83
- grub> setup (hd0)
- Checking if "/boot/grub/stage1" exists... no
- Checking if "/grub/stage1" exists... yes
- Checking if "/grub/stage2" exists... yes
- Checking if "/grub/e2fs_stage1_5" exists... yes
- Running "embed /grub/e2fs_stage1_5 (hd0)"... 15 sectors are embedded.
- succeeded
- Running "install /grub/stage1 (hd0) (hd0)1+15 p (hd0,0)/grub/stage2 /grub/grub.conf"... succeeded
- Done.
- grub> reboot
然后修改启动的 /boot/grub/menu.lst 或者 /boot/grub/grub.conf CentOS下这两个文件是绑定的,改一个即可
- [root@mfsmaster home]# vi /boot/grub/menu.lst
- # grub.conf generated by anaconda
- #
- # Note that you do not have to rerun grub after making changes to this file
- # NOTICE: You have a /boot partition. This means that
- # all kernel and initrd paths are relative to /boot/, eg.
- # root (hd1,0)
- # kernel /vmlinuz-version ro root=/dev/VolGroup00/LogVol00
- # initrd /initrd-version.img
- #boot=/dev/sdb
- default=0
- timeout=5
- splashimage=(hd0,0)/grub/splash.xpm.gz
- hiddenmenu
- title CentOS (2.6.18-274.3.1.el5)
- root (hd0,0)
- kernel /vmlinuz-2.6.18-274.3.1.el5 ro root=/dev/VolGroup00/LogVol00
- initrd /initrd-2.6.18-274.3.1.el5.img
- title CentOS (2.6.18-238.el5)
- root (hd0,0)
- kernel /vmlinuz-2.6.18-238.el5 ro root=/dev/VolGroup00/LogVol00
- initrd /initrd-2.6.18-238.el5.img
- title Other
- rootnoverify (hd0,3)
- chainloader +1
把当中的(hd1,0)都改成(hd0,0),splashimage=(hd0,0)/grub/splash.xpm.gz 这个是开机引导背景图片的位置,改不改都关系不大,重启CentOS就可以正常启动了