HAL库硬件spi驱动st7735tft任意尺寸屏幕完整保姆级教学

已于 2024-06-13 16:55:48 修改
阅读量243 收藏 8
点赞数 11
文章标签： stm32 单片机
于 2024-06-13 16:55:12 首次发布
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/lmy040/article/details/139657430
版权

最近要用到tft屏幕，网上的历程又是标准库，所以对他进行了移植，只要按照我的来配置，就可以驱动了

HAL库配置

设置为主从模式，其实主模式就行了，因为这里没有触摸屏

位宽设置为8Bits

分频系数为2

时钟沿极性为高

CPHA设置为第二个时钟沿

软件NSS

再开三个引脚

分别是NSS，BLK，LCD的背光

照着这样配置就行了

然后配置时钟

生成代码

tft_init代码部分：



/*
*   函数内容：TFT发送单个字节数据
*   函数参数：无
*   返回值：无
*/
void TFT_WR_DATA8(uint8_t data)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
    
//    SPI0_Write(data);
	HAL_SPI_Transmit(&hspi1,&data,1,0xfff);
//     HAL_SPI_Transmit_DMA(&hspi1, &data, 1);
    SPI_TFT_CS_HIGH();     //拉高片选信号
}
/*
*   函数内容：TFT发送2个字节数据
*   函数参数：无
*   返回值：无
*/
void TFT_WR_DATA(uint16_t data)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
//    
//    SPI0_Write(data>>8);
		TFT_WR_DATA8(data>>8);
	TFT_WR_DATA8(data);
//	SPI0_Write(data);
	uint8_t data_high = (uint8_t)(data >> 8);  // 获取高8位数据

HAL_SPI_Transmit(&hspi1, &data_high, sizeof(data_high), 0xfff);  // 发送高8位数据

SPI_TFT_CS_HIGH();
}

/*
*   函数内容：TFT发送命令数据
*   函数参数：无
*   返回值：无
*/
void TFT_WR_REG(uint8_t reg)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
    TFT_DC_LOW();       //拉低片选信号
    
   HAL_SPI_Transmit(&hspi1,&reg,sizeof(reg),0xfff);
//	 HAL_SPI_Transmit_DMA(&hspi1,&reg,sizeof(reg));
//    TFT_WR_DATA8(reg);
    TFT_DC_HIGH();     //拉高命令信号
    TFT_DC_HIGH();;     //拉高片选信号
}


void TFT_Address_Set(uint16_t x1,uint16_t y1,uint16_t x2,uint16_t y2)
{
	if(USE_HORIZONTAL==0)
	{
		TFT_WR_REG(0x2a);//列地址设置
		TFT_WR_DATA(x1);
		TFT_WR_DATA(x2);
		TFT_WR_REG(0x2b);//行地址设置
		TFT_WR_DATA(y1);
		TFT_WR_DATA(y2);
		TFT_WR_REG(0x2c);//储存器写
	}
	else if(USE_HORIZONTAL==1)
	{
		TFT_WR_REG(0x2a);//列地址设置
		TFT_WR_DATA(x1);
		TFT_WR_DATA(x2);
		TFT_WR_REG(0x2b);//行地址设置
		TFT_WR_DATA(y1);
		TFT_WR_DATA(y2);
		TFT_WR_REG(0x2c);//储存器写
	}
	else if(USE_HORIZONTAL==2)
	{
		TFT_WR_REG(0x2a);//列地址设置
		TFT_WR_DATA(x1);
		TFT_WR_DATA(x2);
		TFT_WR_REG(0x2b);//行地址设置
		TFT_WR_DATA(y1);
		TFT_WR_DATA(y2);
		TFT_WR_REG(0x2c);//储存器写
	}
	else
	{
		TFT_WR_REG(0x2a);//列地址设置
		TFT_WR_DATA(x1);
		TFT_WR_DATA(x2);
		TFT_WR_REG(0x2b);//行地址设置
		TFT_WR_DATA(y1);
		TFT_WR_DATA(y2);
		TFT_WR_REG(0x2c);//储存器写
	}    
}

void TFT_Init(void)
{
//    TFT_GPIO_Init();
//    Init_SPI0_GPIO();
    
    TFT_REST_LOW();   //复位
    HAL_Delay(100);
    TFT_REST_HIGH();     //
    HAL_Delay(100);
    
    TFT_BLK_HIGH();     //打开背光
    HAL_Delay(100);
    
	//************* Start Initial Sequence **********//
	TFT_WR_REG(0x11); //Sleep out 
	HAL_Delay(120);              //Delay 120ms 
	//------------------------------------ST7735S Frame Rate-----------------------------------------// 
	TFT_WR_REG(0xB1); 
	TFT_WR_DATA8(0x05); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_REG(0xB2); 
	TFT_WR_DATA8(0x05);
	TFT_WR_DATA8(0x3C); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_REG(0xB3); 
	TFT_WR_DATA8(0x05); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_DATA8(0x05); 
	TFT_WR_DATA8(0x3C); 
	TFT_WR_DATA8(0x3C); 
	//------------------------------------End ST7735S Frame Rate---------------------------------// 
	TFT_WR_REG(0xB4); //Dot inversion 
	TFT_WR_DATA8(0x03); 
	//------------------------------------ST7735S Power Sequence---------------------------------// 
	TFT_WR_REG(0xC0); 
	TFT_WR_DATA8(0x28); 
	TFT_WR_DATA8(0x08); 
	TFT_WR_DATA8(0x04); 
	TFT_WR_REG(0xC1); 
	TFT_WR_DATA8(0XC0); 
	TFT_WR_REG(0xC2); 
	TFT_WR_DATA8(0x0D); 
	TFT_WR_DATA8(0x00); 
	TFT_WR_REG(0xC3); 
	TFT_WR_DATA8(0x8D); 
	TFT_WR_DATA8(0x2A); 
	TFT_WR_REG(0xC4); 
	TFT_WR_DATA8(0x8D); 
	TFT_WR_DATA8(0xEE); 
	//---------------------------------End ST7735S Power Sequence-------------------------------------// 
	TFT_WR_REG(0xC5); //VCOM 
	TFT_WR_DATA8(0x1A); 
	TFT_WR_REG(0x36); //MX, MY, RGB mode 
	if(USE_HORIZONTAL==0){
        TFT_WR_DATA8(0x00);
    }
	else if(USE_HORIZONTAL==1){
        TFT_WR_DATA8(0xC0);
    }
	else if(USE_HORIZONTAL==2){
        TFT_WR_DATA8(0x70);
    }
	else {
        TFT_WR_DATA8(0xA0); 
    }
	//------------------------------------ST7735S Gamma Sequence---------------------------------// 
	TFT_WR_REG(0xE0); 
	TFT_WR_DATA8(0x04); 
	TFT_WR_DATA8(0x22); 
	TFT_WR_DATA8(0x07); 
	TFT_WR_DATA8(0x0A); 
	TFT_WR_DATA8(0x2E); 
	TFT_WR_DATA8(0x30); 
	TFT_WR_DATA8(0x25); 
	TFT_WR_DATA8(0x2A); 
	TFT_WR_DATA8(0x28); 
	TFT_WR_DATA8(0x26); 
	TFT_WR_DATA8(0x2E); 
	TFT_WR_DATA8(0x3A); 
	TFT_WR_DATA8(0x00); 
	TFT_WR_DATA8(0x01); 
	TFT_WR_DATA8(0x03); 
	TFT_WR_DATA8(0x13); 
	TFT_WR_REG(0xE1); 
	TFT_WR_DATA8(0x04); 
	TFT_WR_DATA8(0x16); 
	TFT_WR_DATA8(0x06); 
	TFT_WR_DATA8(0x0D); 
	TFT_WR_DATA8(0x2D); 
	TFT_WR_DATA8(0x26); 
	TFT_WR_DATA8(0x23); 
	TFT_WR_DATA8(0x27); 
	TFT_WR_DATA8(0x27); 
	TFT_WR_DATA8(0x25); 
	TFT_WR_DATA8(0x2D); 
	TFT_WR_DATA8(0x3B); 
	TFT_WR_DATA8(0x00); 
	TFT_WR_DATA8(0x01); 
	TFT_WR_DATA8(0x04); 
	TFT_WR_DATA8(0x13); 
	//------------------------------------End ST7735S Gamma Sequence-----------------------------// 
	TFT_WR_REG(0x3A); //65k mode 
	TFT_WR_DATA8(0x05); 
	TFT_WR_REG(0x29); //Display on   
}

tft_init.h文件

#ifndef __TFT_INIT_H
#define __TFT_INIT_H
#include "main.h"
#include <stdio.h>

//#define TFT_SCL PA5*
//#define TFT_SDA PA7*
//#define TFT_RES PB5
//#define TFT_DC  PB6
//#define TFT_CS  PB7*
//#define TFT_BLK PB8

#define USE_HORIZONTAL 2  //设置横屏或者竖屏显示 0或1为竖屏 2或3为横屏
#include "gpio.h"

#if USE_HORIZONTAL==0||USE_HORIZONTAL==1
#define LCD_W 128
#define LCD_H 160

#else
#define LCD_W 160
#define LCD_H 128
#endif

/*SPI接口定义-开头****************************/
#define      TFT_SPIx                        SPI1
//#define      TFT_SPI_APBxClock_FUN         RCC_APB2PeriphClockCmd
//#define      TFT_SPI_CLK                   RCC_APB2Periph_SPI1

//CS(NSS)引脚 片选选普通GPIO即可
#define      TFT_SPI_CS_APBxClock_FUN        RCC_APB2PeriphClockCmd
#define      TFT_SPI_CS_CLK                  RCC_APB2Periph_GPIOB    
#define      TFT_SPI_CS_PORT                 GPIOB
#define      TFT_SPI_CS_PIN                  GPIO_PIN_7

//SCK引脚
#define      TFT_SPI_SCK_APBxClock_FUN       RCC_APB2PeriphClockCmd
#define      TFT_SPI_SCK_CLK                 RCC_APB2Periph_GPIOA   
#define      TFT_SPI_SCK_PORT                GPIOA   
#define      TFT_SPI_SCK_PIN                 GPIO_PIN_5
//MISO引脚,示波器只使用半双工
#define      TFT_SPI_MISO_APBxClock_FUN      RCC_APB2PeriphClockCmd
#define      TFT_SPI_MISO_CLK                RCC_APB2Periph_GPIOA    
#define      TFT_SPI_MISO_PORT               GPIOA 
#define      TFT_SPI_MISO_PIN                GPIO_PIN_6
//MOSI引脚
#define      TFT_SPI_MOSI_APBxClock_FUN      RCC_APB2PeriphClockCmd
#define      TFT_SPI_MOSI_CLK                RCC_APB2Periph_GPIOA    
#define      TFT_SPI_MOSI_PORT               GPIOA 
#define      TFT_SPI_MOSI_PIN                GPIO_PIN_7

#define  		SPI_TFT_CS_LOW()     						 HAL_GPIO_WritePin(TFT_SPI_CS_PORT,TFT_SPI_CS_PIN,GPIO_PIN_RESET)

#define  		SPI_TFT_CS_HIGH()    						HAL_GPIO_WritePin(TFT_SPI_CS_PORT,TFT_SPI_CS_PIN,GPIO_PIN_SET)

/*SPI接口定义-结尾****************************/

//背光接口
#define      BLK_GPIO_PORT      GPIOB
#define      BLK_GPIO_CLK       RCC_APB2Periph_GPIOB    
#define      BLK_GPIO_PIN       GPIO_PIN_8 


//REST接口
#define      REST_GPIO_PORT      GPIOB
#define      REST_GPIO_CLK       RCC_APB2Periph_GPIOB    
#define      REST_GPIO_PIN       GPIO_PIN_5  


//DC接口,此接口为TFT屏幕命令接口
#define      DC_GPIO_PORT       GPIOB
#define      DC_GPIO_CLK        RCC_APB2Periph_GPIOB    
#define      DC_GPIO_PIN        GPIO_PIN_6 

#define TFT_SCLK_LOW()      HAL_GPIO_WritePin(GPIOA,GPIO_PIN_5,GPIO_PIN_RESET)

#define TFT_SCLK_HIGH()     HAL_GPIO_WritePin(GPIOA,GPIO_PIN_5,GPIO_PIN_SET)

#define TFT_MOSI_LOW()      HAL_GPIO_WritePin(GPIOA,GPIO_PIN_7,GPIO_PIN_RESET)//SDA=MOSI
#define TFT_MOSI_HIGH()     HAL_GPIO_WritePin(GPIOA,GPIO_PIN_7,GPIO_PIN_SET)

#define TFT_REST_LOW()     	HAL_GPIO_WritePin( REST_GPIO_PORT, REST_GPIO_PIN,GPIO_PIN_RESET)//REST
#define TFT_REST_HIGH()    	HAL_GPIO_WritePin( REST_GPIO_PORT, REST_GPIO_PIN,GPIO_PIN_SET)

#define TFT_DC_LOW()        HAL_GPIO_WritePin( DC_GPIO_PORT, DC_GPIO_PIN,GPIO_PIN_RESET)//DC
#define TFT_DC_HIGH()       HAL_GPIO_WritePin( DC_GPIO_PORT, DC_GPIO_PIN,GPIO_PIN_SET)
 		     
#define TFT_CS_LOW()        HAL_GPIO_WritePin(GPIOB,GPIO_PIN_7,GPIO_PIN_RESET)//CS
#define TFT_CS_HIGH()        HAL_GPIO_WritePin(GPIOB,GPIO_PIN_7,GPIO_PIN_SET)

#define TFT_BLK_LOW()     	HAL_GPIO_WritePin( BLK_GPIO_PORT,BLK_GPIO_PIN,GPIO_PIN_RESET)//BLK
#define TFT_BLK_HIGH()    	HAL_GPIO_WritePin( BLK_GPIO_PORT,BLK_GPIO_PIN,GPIO_PIN_SET)



void TFT_WR_DATA8(uint8_t TxData);
void TFT_WR_DATA(uint16_t data);
void TFT_WR_REG(uint8_t reg);
void TFT_Address_Set(uint16_t x1,uint16_t y1,uint16_t x2,uint16_t y2);
void TFT_Init(void);
void TFT_WR_DATA8_DMA(uint8_t data);
void TFT_WR_DATA_DMA(uint16_t data);
void TFT_WR_REG_DMA(uint8_t reg);
#endif

这个部分可以设置屏幕长度

#define USE_HORIZONTAL 2  //设置横屏或者竖屏显示 0或1为竖屏 2或3为横屏
#include "gpio.h"

#if USE_HORIZONTAL==0||USE_HORIZONTAL==1
#define LCD_W 128
#define LCD_H 160

#else
#define LCD_W 160
#define LCD_H 128
#endif

硬件初始化部分，有这部分屏幕就已经可以亮了

然后开始写字

tft.h文件

#ifndef __TFT_H
#define __TFT_H

#include <stdio.h>
#include "main.h"
//画笔颜色
#define WHITE         	 0xFFFF
#define BLACK         	 0x0000	  
#define BLUE           	 0x001F  
#define BRED             0XF81F
#define GRED 			 0XFFE0
#define GBLUE			 0X07FF
#define RED           	 0xF800
#define MAGENTA       	 0xF81F
#define GREEN         	 0x07E0
#define CYAN          	 0x7FFF
#define YELLOW        	 0xFFE0
#define PURPLE           0x780F //紫色  
#define BROWN 			 0XBC40 //棕色
#define BRRED 			 0XFC07 //棕红色
#define GRAY  			 0X8430 //灰色
#define DARKBLUE      	 0X01CF	//深蓝色
#define LIGHTBLUE      	 0X7D7C	//浅蓝色  
#define GRAYBLUE       	 0X5458 //灰蓝色
#define LIGHTGREEN     	 0X841F //浅绿色
#define LGRAY 			 0XC618 //浅灰色(PANNEL),窗体背景色
#define LGRAYBLUE        0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE           0X2B12 //浅棕蓝色(选择条目的反色)
    
void TFT_Fill(uint16_t xsta,uint16_t ysta,uint16_t xend,uint16_t yend,uint16_t color);
void TFT_DrawPoint(uint16_t x,uint16_t y, uint16_t color);
void TFT_DrawLine(uint16_t x1,uint16_t y1,uint16_t x2,uint16_t y2,uint16_t color);
void TFT_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2,uint16_t color);
void Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r,uint16_t color);
void drawCurve(uint8_t yOffset,short int rawValue);
void TFT_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_ShowString(uint16_t x,uint16_t y,const uint8_t *p,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_ShowChinese(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_ShowChinese12x12(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_ShowChinese16x16(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_ShowChinese24x24(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode);
void TFT_StaticUI(void);
//void TFT_ShowUI(volatile const struct Oscilloscope *value);

#endif

tft.c文件

#include "tft.h"
#include "tft_int.h"
#include "string.h"
#include "font.h"

/*
*   函数内容：  在指定区域填充颜色
*   函数参数：  xsta,ysta---起始坐标
*               xend，yend---终止坐标
*               color--------要填充的颜色
*   返回值：    无
*/
void TFT_Fill(uint16_t xsta,uint16_t ysta,uint16_t xend,uint16_t yend,uint16_t color)
{
    uint16_t i=0,j=0;
    TFT_Address_Set(xsta,ysta,xend-1,yend-1);   //设置显示范围
    for(i=ysta;i<yend;i++)
    {
        for(j=xsta;j<xend;j++)
        {
            TFT_WR_DATA(color);
        }
    }
}

/*
*   函数内容：  在指定位置画点
*   函数参数：  x,y---画点坐标
*               color--------要填充的颜色
*   返回值：    无
*/
void TFT_DrawPoint(uint16_t x,uint16_t y, uint16_t color)
{
    TFT_Address_Set(x,y,x,y);   //设置显示范围
    TFT_WR_DATA(color);
}

/*
*   函数内容：  画线
*   函数参数：  x1,y1   起始坐标
*               x2,y2   终止坐标
*               color   要填充的颜色
*   返回值：    无
*/
void TFT_DrawLine(uint16_t x1,uint16_t y1,uint16_t x2,uint16_t y2,uint16_t color)
{ 
    uint16_t i=0;
	uint16_t t=0; 
	int xerr=0,yerr=0,delta_x=0,delta_y=0,distance=0;
	int incx=0,incy=0,uRow=0,uCol=0;
	delta_x=x2-x1; //计算坐标增量 
	delta_y=y2-y1;
	uRow=x1;//画线起点坐标
	uCol=y1;
	if(delta_x>0){
        incx=1; //设置单步方向 
    }
	else if (delta_x==0){
        incx=0;//垂直线 
    }
	else {
        incx=-1;
        delta_x=-delta_x;
    }
	if(delta_y>0){
        incy=1;
    }
	else if (delta_y==0){
        incy=0;//水平线 
    }
	else {
        incy=-1;
        delta_y=-delta_y;
    }
	if(delta_x>delta_y){
        distance=delta_x; //选取基本增量坐标轴 
    }
	else {
        distance=delta_y;
    }
	for(t=0;t<distance+1;t++)
	{
		TFT_DrawPoint(uRow,uCol,color);//画点 

        for(i=30;i<80;i++)
        {
            TFT_DrawPoint(uRow+1,i,BLACK);//画点
        }
        
		xerr+=delta_x;
		yerr+=delta_y;
		if(xerr>distance)
		{
			xerr-=distance;
			uRow+=incx;
		}
		if(yerr>distance)
		{
			yerr-=distance;
			uCol+=incy;
		}
	}
}

/*
*   函数内容：  画矩形
*   函数参数：  x1,y1   起始坐标
*               x2,y2   终止坐标
*               color   矩形的颜色
*   返回值：    无
*/
void TFT_DrawRectangle(uint16_t x1, uint16_t y1, uint16_t x2, uint16_t y2,uint16_t color)
{
	TFT_DrawLine(x1,y1,x2,y1,color);
	TFT_DrawLine(x1,y1,x1,y2,color);
	TFT_DrawLine(x1,y2,x2,y2,color);
	TFT_DrawLine(x2,y1,x2,y2,color);
}

/*
*   函数内容：  画圆
*   函数参数：  x0,y0   圆心坐标
*               r       半径
*               color   矩形的颜色
*   返回值：    无
*/
void Draw_Circle(uint16_t x0,uint16_t y0,uint8_t r,uint16_t color)
{
	uint16_t a=0,b=0;
	a=0;b=r;	  
	while(a<=b)
	{
		TFT_DrawPoint(x0-b,y0-a,color);             //3           
		TFT_DrawPoint(x0+b,y0-a,color);             //0           
		TFT_DrawPoint(x0-a,y0+b,color);             //1                
		TFT_DrawPoint(x0-a,y0-b,color);             //2             
		TFT_DrawPoint(x0+b,y0+a,color);             //4               
		TFT_DrawPoint(x0+a,y0-b,color);             //5
		TFT_DrawPoint(x0+a,y0+b,color);             //6 
		TFT_DrawPoint(x0-b,y0+a,color);             //7
		a++;
		if((a*a+b*b)>(r*r))//判断要画的点是否过远
		{
			b--;
		}
	}
}

static uint16_t lastX=0,lastY=0;
static uint8_t firstPoint = 1;

/*
*   函数内容：画折线
*   函数参数：short int rawValue--Y轴参数值
*   返回值：  无
*/
void drawCurve(uint8_t yOffset,short int rawValue)  
{
	uint16_t x=0,y=0;
	y = yOffset - rawValue;  	//data processing code
	if(firstPoint)//如果是第一次画点，则无需连线，直接描点即可
	{
		TFT_DrawPoint(0,y,GREEN);   
		lastX=0;
		lastY=y;
		firstPoint=0; 
	}
	else
	{
		x=lastX+1;
        
		if(x<100)  //不超过屏幕宽度
		{
			TFT_DrawLine(lastX,lastY,x,y,GREEN);            
			lastX=x;
			lastY=y;
		}
		else  //超出屏幕宽度，清屏，从第一个点开始绘制，实现动态更新效果
		{         
			//TFT_Fill(0,0,160,128,WHITE);//清屏，白色背景
			TFT_DrawPoint(0,y,GREEN);   
			lastX=0;
			lastY=y;
		}
  }
}

/*
*   函数内容：显示字符
*   函数参数：  x,y---起始坐标
*               num 要显示的字符
*               fc 字的颜色
*               bc 字的背景色
*               sizey 字号
*               mode:  0非叠加模式  1叠加模式
*   返回值：    无
*/
void TFT_ShowChar(uint16_t x,uint16_t y,uint8_t num,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{
	uint8_t temp,sizex,t,m=0;
	uint16_t i,TypefaceNum;//一个字符所占字节大小
	uint16_t x0=x;
	sizex=sizey/2;
	TypefaceNum=(sizex/8+((sizex%8)?1:0))*sizey;
	num=num-' ';    //得到偏移后的值
	TFT_Address_Set(x,y,x+sizex-1,y+sizey-1);  //设置光标位置 
	for(i=0;i<TypefaceNum;i++)
	{ 
		if(sizey==12){
            temp=ascii_1206[num][i];		       //调用6x12字体
        }
		else if(sizey==16){
            temp=ascii_1608[num][i];		 //调用8x16字体
        }
		else if(sizey==24){
            temp=ascii_2412[num][i];		 //调用12x24字体
        }
		else {
            return;
        }
		for(t=0;t<8;t++)
		{
			if(!mode)//非叠加模式
			{
				if(temp&(0x01<<t)){
                    TFT_WR_DATA(fc);
                }
				else {
                    TFT_WR_DATA(bc);
                }
				m++;
				if(m%sizex==0)
				{
					m=0;
					break;
				}
			}
			else//叠加模式
			{
				if(temp&(0x01<<t)){
                    TFT_DrawPoint(x,y,fc);//画一个点
                }
				x++;
				if((x-x0)==sizex)
				{
					x=x0;
					y++;
					break;
				}
			}
		}
	}   	 	  
}

/*
*   函数内容：  显示字符串
*   函数参数：  x,y---起始坐标
*               *p 要显示的字符串
*               fc 字的颜色
*               bc 字的背景色
*               sizey 字号
*               mode:  0非叠加模式  1叠加模式
*   返回值：    无
*/
void TFT_ShowString(uint16_t x,uint16_t y,const uint8_t *p,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{         
	while(*p!='\0')
	{       
		TFT_ShowChar(x,y,*p,fc,bc,sizey,mode);
		x+=sizey/2;
		p++;
	}  
}

/******************************************************************************
      函数说明：显示汉字串
      入口数据：x,y显示坐标
                *s 要显示的汉字串
                fc 字的颜色
                bc 字的背景色
                sizey 字号 可选 16 24 32
                mode:  0非叠加模式  1叠加模式
      返回值：  无
******************************************************************************/
void TFT_ShowChinese(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{
	while(*s!=0)
	{
		if(sizey==12) {
            TFT_ShowChinese12x12(x,y,s,fc,bc,sizey,mode);
        }
		else if(sizey==16) {
            TFT_ShowChinese16x16(x,y,s,fc,bc,sizey,mode);
        }
		else if(sizey==24) {
            TFT_ShowChinese24x24(x,y,s,fc,bc,sizey,mode);
        }
		s+=2;
		x+=sizey;
	}
}

/******************************************************************************
      函数说明：显示单个12x12汉字
      入口数据：x,y显示坐标
                *s 要显示的汉字
                fc 字的颜色
                bc 字的背景色
                sizey 字号
                mode:  0非叠加模式  1叠加模式
      返回值：  无
******************************************************************************/
void TFT_ShowChinese12x12(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{
	uint8_t i=0,j=0,m=0;
	uint16_t k=0;
	uint16_t HZnum=0;//汉字数目
	uint16_t TypefaceNum=0;//一个字符所占字节大小
	uint16_t x0=x;
	TypefaceNum=(sizey/8+((sizey%8)?1:0))*sizey;
	                         
	HZnum=sizeof(tfont12)/sizeof(typFNT_GB12);	//统计汉字数目
	for(k=0;k<HZnum;k++) 
	{
		if((tfont12[k].Index[0]==*(s))&&(tfont12[k].Index[1]==*(s+1)))
		{ 	
			TFT_Address_Set(x,y,x+sizey-1,y+sizey-1);
			for(i=0;i<TypefaceNum;i++)
			{
				for(j=0;j<8;j++)
				{	
					if(!mode)//非叠加方式
					{
						if(tfont12[k].Msk[i]&(0x01<<j)){
                            TFT_WR_DATA(fc);
                        }
						else {
                            TFT_WR_DATA(bc);
                        }
						m++;
						if(m%sizey==0)
						{
							m=0;
							break;
						}
					}
					else//叠加方式
					{
						if(tfont12[k].Msk[i]&(0x01<<j))	{
                            TFT_DrawPoint(x,y,fc);//画一个点
                        }
						x++;
						if((x-x0)==sizey)
						{
							x=x0;
							y++;
							break;
						}
					}
				}
			}
		}				  	
		continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
	}
} 

/******************************************************************************
      函数说明：显示单个16x16汉字
      入口数据：x,y显示坐标
                *s 要显示的汉字
                fc 字的颜色
                bc 字的背景色
                sizey 字号
                mode:  0非叠加模式  1叠加模式
      返回值：  无
******************************************************************************/
void TFT_ShowChinese16x16(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{
	uint8_t i=0,j=0,m=0;
	uint16_t k=0;
	uint16_t HZnum=0;//汉字数目
	uint16_t TypefaceNum=0;//一个字符所占字节大小
	uint16_t x0=x;
    TypefaceNum=(sizey/8+((sizey%8)?1:0))*sizey;
	HZnum=sizeof(tfont16)/sizeof(typFNT_GB16);	//统计汉字数目
	for(k=0;k<HZnum;k++) 
	{
		if ((tfont16[k].Index[0]==*(s))&&(tfont16[k].Index[1]==*(s+1)))
		{ 	
			TFT_Address_Set(x,y,x+sizey-1,y+sizey-1);
			for(i=0;i<TypefaceNum;i++)
			{
				for(j=0;j<8;j++)
				{	
					if(!mode)//非叠加方式
					{
						if(tfont16[k].Msk[i]&(0x01<<j)){
                            TFT_WR_DATA(fc);
                        }
						else {
                            TFT_WR_DATA(bc);
                        }
						m++;
						if(m%sizey==0)
						{
							m=0;
							break;
						}
					}
					else//叠加方式
					{
						if(tfont16[k].Msk[i]&(0x01<<j)){
                            TFT_DrawPoint(x,y,fc);//画一个点
                        }
						x++;
						if((x-x0)==sizey)
						{
							x=x0;
							y++;
							break;
						}
					}
				}
			}
		}				  	
		continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
	}
} 

/******************************************************************************
      函数说明：显示单个24x24汉字
      入口数据：x,y显示坐标
                *s 要显示的汉字
                fc 字的颜色
                bc 字的背景色
                sizey 字号
                mode:  0非叠加模式  1叠加模式
      返回值：  无
******************************************************************************/
void TFT_ShowChinese24x24(uint16_t x,uint16_t y,uint8_t *s,uint16_t fc,uint16_t bc,uint8_t sizey,uint8_t mode)
{
	uint8_t i=0,j=0,m=0;
	uint16_t k=0;
	uint16_t HZnum=0;//汉字数目
	uint16_t TypefaceNum=0;//一个字符所占字节大小
	uint16_t x0=x;
	TypefaceNum=(sizey/8+((sizey%8)?1:0))*sizey;
	HZnum=sizeof(tfont24)/sizeof(typFNT_GB24);	//统计汉字数目
	for(k=0;k<HZnum;k++) 
	{
		if ((tfont24[k].Index[0]==*(s))&&(tfont24[k].Index[1]==*(s+1)))
		{ 	
			TFT_Address_Set(x,y,x+sizey-1,y+sizey-1);
			for(i=0;i<TypefaceNum;i++)
			{
				for(j=0;j<8;j++)
				{	
					if(!mode)//非叠加方式
					{
						if(tfont24[k].Msk[i]&(0x01<<j)){
                            TFT_WR_DATA(fc);
                        }
						else{
                            TFT_WR_DATA(bc);
                        }
						m++;
						if(m%sizey==0)
						{
							m=0;
							break;
						}
					}
					else//叠加方式
					{
						if(tfont24[k].Msk[i]&(0x01<<j)){
                            TFT_DrawPoint(x,y,fc);//画一个点
                        }
						x++;
						if((x-x0)==sizey)
						{
							x=x0;
							y++;
							break;
						}
					}
				}
			}
		}				  	
		continue;  //查找到对应点阵字库立即退出，防止多个汉字重复取模带来影响
	}
} 

/*
*   函数内容：静止UI界面
*   函数参数：无
*   返回值：  无
*/
void TFT_StaticUI(void)
{
    uint16_t i=0;
    
    char showData[32]={0};
    
    TFT_ShowChinese(10,0,(uint8_t *)"简易示波器",BLACK,GREEN,16,0);
    
    sprintf(showData,"  PWM ");
    TFT_ShowString(110,0,(uint8_t *)showData,BLACK,YELLOW,16,0);  
    memset(showData,0,32);
    
    TFT_ShowChinese(110,20,(uint8_t *)"输出状态",WHITE,PURPLE,12,0);
    
    sprintf(showData,"      ");
    TFT_ShowString(110,36,(uint8_t *)showData,BLACK,YELLOW,16,0);  
    memset(showData,0,32);
    
    TFT_ShowChinese(110,56,(uint8_t *)"输出频率",WHITE,PURPLE,12,0);
    
    sprintf(showData,"      ");
    TFT_ShowString(110,72,(uint8_t *)showData,BLACK,YELLOW,16,0);  
    memset(showData,0,32);
    
    sprintf(showData,"        ");
    TFT_ShowString(110,92,(uint8_t *)showData,WHITE,PURPLE,12,0);  
    memset(showData,0,32);
    TFT_ShowChinese(118,92,(uint8_t *)"占空比",WHITE,PURPLE,12,0);
    
    sprintf(showData,"      ");
    TFT_ShowString(110,106,(uint8_t *)showData,BLACK,YELLOW,16,0);  
    memset(showData,0,32);
    
    TFT_ShowChinese(5,92,(uint8_t *)"输入幅值",WHITE,PURPLE,12,0);
    
    TFT_ShowChinese(55,92,(uint8_t *)"输入频率",WHITE,PURPLE,12,0);
    
    for(i=0;i<=128;i=i+2)
    {
        TFT_DrawPoint(106,i,YELLOW);
    }
    
    for(i=0;i<100;i++)
    {
        TFT_DrawPoint(i,81,GREEN);
    }
    for(i=0;i<10;i++)
    {
        TFT_DrawPoint((i*10)+2,82,GREEN); 
        TFT_DrawPoint((i*10)+3,82,GREEN); 
    }
    for(i=0;i<10;i++)
    {
        TFT_DrawPoint((i*10)+2,83,GREEN); 
        TFT_DrawPoint((i*10)+3,83,GREEN);
    }
}
/*
*   函数内容：  显示字符串
*   函数参数：  uint16_t vpp--峰峰值
*               uint16_t freq-频率
*               float DoBias--直流偏执信号
*   返回值：    无
*/
uint16_t readvalue1 = 0, readvalue2 = 0;
__IO uint16_t ccnumber = 0;
__IO uint32_t count = 0;
__IO float freq=0;
extern volatile struct Oscilloscope oscilloscope;
//void TFT_ShowUI(volatile const struct Oscilloscope *value)
//{
//    char showData[64]={0};
//    
//    sprintf(showData,"%1.2fV ",(*value).vpp);
//    TFT_ShowString(5,106,(uint8_t *)showData,BLACK,GREEN,16,0);  
//    memset(showData,0,64);
//    
//    if((*value).gatherFreq>=1000)
//    {
//        sprintf(showData,"%2.0fKHz ",(*value).gatherFreq/1000.0f);
//        TFT_ShowString(55,106,(uint8_t *)showData,BLACK,GREEN,16,0);  
//        memset(showData,0,64);
//    }
//    else
//    {
//        sprintf(showData,"%3.0fHz ",(*value).gatherFreq);
//        TFT_ShowString(55,106,(uint8_t *)showData,BLACK,GREEN,16,0);  
//        memset(showData,0,64);  
//    }

//    if((*value).ouptputbit == 1)
//    {   
//        TFT_ShowChinese(118,36,(uint8_t *)"打开",BLACK,YELLOW,16,0);
//    }
//    else
//    {
//        TFT_ShowChinese(118,36,(uint8_t *)"关闭",BLACK,YELLOW,16,0);     
//    }
//    
//    if((*value).outputFreq>=1000)
//    {
//        sprintf(showData,"%3dKHz",(*value).outputFreq/1000);
//        TFT_ShowString(110,72,(uint8_t *)showData,BLACK,YELLOW,16,0);  
//        memset(showData,0,64); 
//    }
//    else
//    {
//        sprintf(showData," %3dHz",(*value).outputFreq);
//        TFT_ShowString(110,72,(uint8_t *)showData,BLACK,YELLOW,16,0);  
//        memset(showData,0,64);
//    }  
//    
//    sprintf(showData,"%3.1f%%  ",(((*value).pwmOut)/((*value).timerPeriod+0.0f))*100);
//    TFT_ShowString(110,106,(uint8_t *)showData,BLACK,YELLOW,16,0);  
//    memset(showData,0,64);        
//}

font.h

#ifndef __LCDFONT_H
#define __LCDFONT_H

const unsigned char ascii_1206[][12]={

{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x00,0x00,0x04,0x00,0x00},/*"!",1*/
{0x14,0x14,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x0A,0x0A,0x1F,0x0A,0x0A,0x1F,0x0A,0x0A,0x00,0x00},/*"#",3*/
{0x00,0x04,0x0E,0x15,0x05,0x06,0x0C,0x14,0x15,0x0E,0x04,0x00},/*"$",4*/
{0x00,0x00,0x12,0x15,0x0D,0x15,0x2E,0x2C,0x2A,0x12,0x00,0x00},/*"%",5*/
{0x00,0x00,0x04,0x0A,0x0A,0x36,0x15,0x15,0x29,0x16,0x00,0x00},/*"&",6*/
{0x02,0x02,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x10,0x08,0x08,0x04,0x04,0x04,0x04,0x04,0x08,0x08,0x10,0x00},/*"(",8*/
{0x02,0x04,0x04,0x08,0x08,0x08,0x08,0x08,0x04,0x04,0x02,0x00},/*")",9*/
{0x00,0x00,0x00,0x04,0x15,0x0E,0x0E,0x15,0x04,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x00,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x02,0x01,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0x00,0x00},/*".",14*/
{0x00,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x01,0x00},/*"/",15*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"0",16*/
{0x00,0x00,0x04,0x06,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"1",17*/
{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x02,0x01,0x1F,0x00,0x00},/*"2",18*/
{0x00,0x00,0x0E,0x11,0x10,0x0C,0x10,0x10,0x11,0x0E,0x00,0x00},/*"3",19*/
{0x00,0x00,0x08,0x0C,0x0C,0x0A,0x09,0x1F,0x08,0x1C,0x00,0x00},/*"4",20*/
{0x00,0x00,0x1F,0x01,0x01,0x0F,0x11,0x10,0x11,0x0E,0x00,0x00},/*"5",21*/
{0x00,0x00,0x0C,0x12,0x01,0x0D,0x13,0x11,0x11,0x0E,0x00,0x00},/*"6",22*/
{0x00,0x00,0x1E,0x10,0x08,0x08,0x04,0x04,0x04,0x04,0x00,0x00},/*"7",23*/
{0x00,0x00,0x0E,0x11,0x11,0x0E,0x11,0x11,0x11,0x0E,0x00,0x00},/*"8",24*/
{0x00,0x00,0x0E,0x11,0x11,0x19,0x16,0x10,0x09,0x06,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x00,0x04,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x00,0x00,0x04,0x04,0x00},/*";",27*/
{0x00,0x00,0x10,0x08,0x04,0x02,0x02,0x04,0x08,0x10,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x3F,0x00,0x3F,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x02,0x04,0x08,0x10,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/
{0x00,0x00,0x0E,0x11,0x11,0x08,0x04,0x04,0x00,0x04,0x00,0x00},/*"?",31*/
{0x00,0x00,0x1C,0x22,0x29,0x2D,0x2D,0x1D,0x22,0x1C,0x00,0x00},/*"@",32*/
{0x00,0x00,0x04,0x04,0x0C,0x0A,0x0A,0x1E,0x12,0x33,0x00,0x00},/*"A",33*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x12,0x12,0x12,0x0F,0x00,0x00},/*"B",34*/
{0x00,0x00,0x1E,0x11,0x01,0x01,0x01,0x01,0x11,0x0E,0x00,0x00},/*"C",35*/
{0x00,0x00,0x0F,0x12,0x12,0x12,0x12,0x12,0x12,0x0F,0x00,0x00},/*"D",36*/
{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x12,0x1F,0x00,0x00},/*"E",37*/
{0x00,0x00,0x1F,0x12,0x0A,0x0E,0x0A,0x02,0x02,0x07,0x00,0x00},/*"F",38*/
{0x00,0x00,0x1C,0x12,0x01,0x01,0x39,0x11,0x12,0x0C,0x00,0x00},/*"G",39*/
{0x00,0x00,0x33,0x12,0x12,0x1E,0x12,0x12,0x12,0x33,0x00,0x00},/*"H",40*/
{0x00,0x00,0x1F,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"I",41*/
{0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x09,0x07},/*"J",42*/
{0x00,0x00,0x37,0x12,0x0A,0x06,0x0A,0x12,0x12,0x37,0x00,0x00},/*"K",43*/
{0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x22,0x3F,0x00,0x00},/*"L",44*/
{0x00,0x00,0x3B,0x1B,0x1B,0x1B,0x15,0x15,0x15,0x35,0x00,0x00},/*"M",45*/
{0x00,0x00,0x3B,0x12,0x16,0x16,0x1A,0x1A,0x12,0x17,0x00,0x00},/*"N",46*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x11,0x11,0x0E,0x00,0x00},/*"O",47*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/
{0x00,0x00,0x0E,0x11,0x11,0x11,0x11,0x17,0x19,0x0E,0x18,0x00},/*"Q",49*/
{0x00,0x00,0x0F,0x12,0x12,0x0E,0x0A,0x12,0x12,0x37,0x00,0x00},/*"R",50*/
{0x00,0x00,0x1E,0x11,0x01,0x06,0x08,0x10,0x11,0x0F,0x00,0x00},/*"S",51*/
{0x00,0x00,0x1F,0x15,0x04,0x04,0x04,0x04,0x04,0x0E,0x00,0x00},/*"T",52*/
{0x00,0x00,0x33,0x12,0x12,0x12,0x12,0x12,0x12,0x0C,0x00,0x00},/*"U",53*/
{0x00,0x00,0x33,0x12,0x12,0x0A,0x0A,0x0C,0x04,0x04,0x00,0x00},/*"V",54*/
{0x00,0x00,0x15,0x15,0x15,0x15,0x0E,0x0A,0x0A,0x0A,0x00,0x00},/*"W",55*/
{0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x0A,0x0A,0x1B,0x00,0x00},/*"X",56*/
{0x00,0x00,0x1B,0x0A,0x0A,0x0A,0x04,0x04,0x04,0x0E,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x1F,0x09,0x08,0x04,0x04,0x02,0x12,0x1F,0x00,0x00},/*"Z",58*/
{0x1C,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x1C,0x00},/*"[",59*/
{0x00,0x02,0x02,0x04,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x00},/*"\",60*/
{0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x0E,0x00},/*"]",61*/
{0x04,0x0A,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3F},/*"_",63*/
{0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1C,0x12,0x3C,0x00,0x00},/*"a",65*/
{0x00,0x03,0x02,0x02,0x02,0x0E,0x12,0x12,0x12,0x0E,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x02,0x12,0x0C,0x00,0x00},/*"c",67*/
{0x00,0x18,0x10,0x10,0x10,0x1C,0x12,0x12,0x12,0x3C,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x1E,0x02,0x1C,0x00,0x00},/*"e",69*/
{0x00,0x18,0x24,0x04,0x04,0x1E,0x04,0x04,0x04,0x1E,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x3C,0x12,0x0C,0x02,0x1C,0x22,0x1C},/*"g",71*/
{0x00,0x03,0x02,0x02,0x02,0x0E,0x12,0x12,0x12,0x37,0x00,0x00},/*"h",72*/
{0x00,0x04,0x04,0x00,0x00,0x06,0x04,0x04,0x04,0x0E,0x00,0x00},/*"i",73*/
{0x00,0x08,0x08,0x00,0x00,0x0C,0x08,0x08,0x08,0x08,0x08,0x07},/*"j",74*/
{0x00,0x03,0x02,0x02,0x02,0x1A,0x0A,0x06,0x0A,0x13,0x00,0x00},/*"k",75*/
{0x00,0x07,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x15,0x15,0x15,0x15,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x37,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0C,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x0F,0x12,0x12,0x12,0x0E,0x02,0x07},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x1C,0x12,0x12,0x12,0x1C,0x10,0x38},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x06,0x02,0x02,0x07,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x1E,0x02,0x0C,0x10,0x1E,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x04,0x04,0x1E,0x04,0x04,0x04,0x1C,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x12,0x12,0x12,0x3C,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x0A,0x0A,0x04,0x04,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x15,0x15,0x0E,0x0A,0x0A,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x1B,0x0A,0x04,0x0A,0x1B,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x33,0x12,0x12,0x0C,0x08,0x04,0x03},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x1E,0x08,0x04,0x04,0x1E,0x00,0x00},/*"z",90*/
{0x18,0x08,0x08,0x08,0x08,0x0C,0x08,0x08,0x08,0x08,0x18,0x00},/*"{",91*/
{0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08},/*"|",92*/
{0x06,0x04,0x04,0x04,0x04,0x08,0x04,0x04,0x04,0x04,0x06,0x00},/*"}",93*/
{0x16,0x09,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
};

const unsigned char ascii_1608[][16]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x18,0x18,0x00,0x00},/*"!",1*/
{0x00,0x48,0x6C,0x24,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x24,0x24,0x24,0x7F,0x12,0x12,0x12,0x7F,0x12,0x12,0x12,0x00,0x00},/*"#",3*/
{0x00,0x00,0x08,0x1C,0x2A,0x2A,0x0A,0x0C,0x18,0x28,0x28,0x2A,0x2A,0x1C,0x08,0x08},/*"$",4*/
{0x00,0x00,0x00,0x22,0x25,0x15,0x15,0x15,0x2A,0x58,0x54,0x54,0x54,0x22,0x00,0x00},/*"%",5*/
{0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0A,0x76,0x25,0x29,0x11,0x91,0x6E,0x00,0x00},/*"&",6*/
{0x00,0x06,0x06,0x04,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00},/*"(",8*/
{0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x6B,0x1C,0x1C,0x6B,0x08,0x08,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x7F,0x08,0x08,0x08,0x08,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x04,0x03},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00},/*".",14*/
{0x00,0x00,0x80,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x00},/*"/",15*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x08,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x20,0x20,0x10,0x08,0x04,0x42,0x7E,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x20,0x18,0x20,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x20,0x30,0x28,0x24,0x24,0x22,0x22,0x7E,0x20,0x20,0x78,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x7E,0x02,0x02,0x02,0x1A,0x26,0x40,0x40,0x42,0x22,0x1C,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x38,0x24,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x24,0x18,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x7E,0x22,0x22,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x64,0x58,0x40,0x40,0x24,0x1C,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x04},/*";",27*/
{0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x3C,0x42,0x42,0x46,0x40,0x20,0x10,0x10,0x00,0x18,0x18,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x1C,0x22,0x5A,0x55,0x55,0x55,0x55,0x2D,0x42,0x22,0x1C,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x08,0x08,0x18,0x14,0x14,0x24,0x3C,0x22,0x42,0x42,0xE7,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x1E,0x22,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x01,0x01,0x01,0x01,0x01,0x42,0x22,0x1C,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x1F,0x22,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1F,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x42,0x42,0x3F,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x02,0x02,0x07,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x3C,0x22,0x22,0x01,0x01,0x01,0x71,0x21,0x22,0x22,0x1C,0x00,0x00},/*"G",39*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x11,0x0F},/*"J",42*/
{0x00,0x00,0x00,0x77,0x22,0x12,0x0A,0x0E,0x0A,0x12,0x12,0x22,0x22,0x77,0x00,0x00},/*"K",43*/
{0x00,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x7F,0x00,0x00},/*"L",44*/
{0x00,0x00,0x00,0x77,0x36,0x36,0x36,0x36,0x2A,0x2A,0x2A,0x2A,0x2A,0x6B,0x00,0x00},/*"M",45*/
{0x00,0x00,0x00,0xE3,0x46,0x46,0x4A,0x4A,0x52,0x52,0x52,0x62,0x62,0x47,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x41,0x41,0x22,0x1C,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x42,0x3E,0x02,0x02,0x02,0x02,0x07,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x4D,0x53,0x32,0x1C,0x60,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x3E,0x12,0x12,0x22,0x22,0x42,0xC7,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x7C,0x42,0x42,0x02,0x04,0x18,0x20,0x40,0x42,0x42,0x3E,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x7F,0x49,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"T",52*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0xE7,0x42,0x42,0x22,0x24,0x24,0x14,0x14,0x18,0x08,0x08,0x00,0x00},/*"V",54*/
{0x00,0x00,0x00,0x6B,0x49,0x49,0x49,0x49,0x55,0x55,0x36,0x22,0x22,0x22,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x77,0x22,0x22,0x14,0x14,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x7E,0x21,0x20,0x10,0x10,0x08,0x04,0x04,0x42,0x42,0x3F,0x00,0x00},/*"Z",58*/
{0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00},/*"[",59*/
{0x00,0x00,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x20,0x20,0x20,0x40,0x40},/*"\",60*/
{0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00},/*"]",61*/
{0x00,0x38,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF},/*"_",63*/
{0x00,0x06,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x78,0x44,0x42,0x42,0xFC,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x26,0x1A,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x44,0x02,0x02,0x02,0x44,0x38,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x60,0x40,0x40,0x40,0x78,0x44,0x42,0x42,0x42,0x64,0xD8,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x02,0x02,0x42,0x3C,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0xF0,0x88,0x08,0x08,0x7E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x22,0x22,0x1C,0x02,0x3C,0x42,0x42,0x3C},/*"g",71*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x3A,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x38,0x20,0x20,0x20,0x20,0x20,0x20,0x22,0x1E},/*"j",74*/
{0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x72,0x12,0x0A,0x16,0x12,0x22,0x77,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x92,0x92,0x92,0x92,0x92,0xB7,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3B,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B,0x26,0x42,0x42,0x42,0x22,0x1E,0x02,0x07},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x44,0x42,0x42,0x42,0x44,0x78,0x40,0xE0},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x77,0x4C,0x04,0x04,0x04,0x04,0x1F,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42,0x02,0x3C,0x40,0x42,0x3E,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x08,0x08,0x08,0x30,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x42,0x42,0x42,0x42,0x62,0xDC,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x08,0x08,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEB,0x49,0x49,0x55,0x55,0x22,0x22,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x76,0x24,0x18,0x18,0x18,0x24,0x6E,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x18,0x08,0x08,0x07},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x22,0x10,0x08,0x08,0x44,0x7E,0x00,0x00},/*"z",90*/
{0x00,0xC0,0x20,0x20,0x20,0x20,0x20,0x10,0x20,0x20,0x20,0x20,0x20,0x20,0xC0,0x00},/*"{",91*/
{0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10},/*"|",92*/
{0x00,0x06,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x06,0x00},/*"}",93*/
{0x0C,0x32,0xC2,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/
}; 

const unsigned char ascii_2412[][48]={
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*" ",0*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"!",1*/
{0x00,0x00,0x00,0x00,0x60,0x06,0x60,0x06,0x30,0x03,0x98,0x01,0x88,0x00,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*""",2*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x10,0x02,0x10,0x02,0x10,0x02,0x10,0x02,0xFE,0x07,0xFE,0x07,0x08,0x02,0x08,0x01,0x08,0x01,0x08,0x01,0x08,0x01,0xFE,0x07,0xFE,0x07,0x04,0x01,0x04,0x01,0x04,0x01,0x04,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"#",3*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x40,0x00,0xF0,0x01,0x58,0x03,0x4C,0x03,0xCC,0x03,0x4C,0x00,0x58,0x00,0x70,0x00,0xE0,0x00,0xC0,0x01,0xC0,0x01,0x40,0x03,0x4C,0x03,0x5C,0x03,0x4C,0x03,0x48,0x01,0xF0,0x00,0x40,0x00,0x40,0x00,0x00,0x00},/*"$",4*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x01,0x0A,0x01,0x91,0x00,0x91,0x00,0x91,0x00,0x51,0x00,0x51,0x00,0x3A,0x00,0xAE,0x03,0xA0,0x02,0x50,0x04,0x50,0x04,0x48,0x04,0x48,0x04,0x48,0x04,0x84,0x02,0x84,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"%",5*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x00,0x6C,0x00,0x6C,0x00,0x6C,0x00,0x6C,0x00,0x6C,0x00,0x2C,0x00,0x98,0x07,0x1C,0x01,0x1A,0x01,0x33,0x01,0x33,0x01,0x63,0x01,0xE3,0x00,0xC3,0x08,0xC6,0x09,0x3C,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"&",6*/
{0x00,0x00,0x00,0x00,0x0C,0x00,0x1C,0x00,0x10,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"'",7*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x02,0x00,0x01,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x80,0x00,0x80,0x00,0x00,0x01,0x00,0x02,0x00,0x04,0x00,0x00},/*"(",8*/
{0x00,0x00,0x00,0x00,0x02,0x00,0x04,0x00,0x08,0x00,0x10,0x00,0x10,0x00,0x20,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x10,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x02,0x00,0x00,0x00},/*")",9*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0xC0,0x00,0x40,0x00,0x46,0x0C,0x4E,0x0F,0xD0,0x01,0xF0,0x01,0x5E,0x0F,0x46,0x0C,0x40,0x00,0x40,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"*",10*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0xFE,0x0F,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"+",11*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0C,0x00,0x1C,0x00,0x10,0x00,0x10,0x00,0x08,0x00,0x04,0x00},/*",",12*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"-",13*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1C,0x00,0x1C,0x00,0x1C,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*".",14*/
{0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x06,0x00,0x02,0x00,0x03,0x00,0x01,0x00,0x01,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x60,0x00,0x20,0x00,0x20,0x00,0x10,0x00,0x10,0x00,0x08,0x00,0x08,0x00,0x0C,0x00,0x04,0x00,0x06,0x00,0x02,0x00,0x00,0x00},/*"/",15*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x98,0x01,0x0C,0x03,0x0C,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x0C,0x03,0x0C,0x03,0x98,0x01,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"0",16*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x7C,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xFC,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"1",17*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x00,0x84,0x01,0x02,0x03,0x06,0x03,0x06,0x03,0x00,0x03,0x00,0x01,0x80,0x01,0xC0,0x00,0x60,0x00,0x20,0x00,0x10,0x00,0x08,0x02,0x04,0x02,0x06,0x02,0xFE,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"2",18*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x00,0xC6,0x00,0x86,0x01,0x86,0x01,0x80,0x01,0x80,0x01,0xC0,0x00,0x70,0x00,0x80,0x01,0x00,0x01,0x00,0x03,0x00,0x03,0x06,0x03,0x06,0x03,0x86,0x01,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"3",19*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x01,0x80,0x01,0xC0,0x01,0xA0,0x01,0xA0,0x01,0x90,0x01,0x88,0x01,0x88,0x01,0x84,0x01,0x82,0x01,0xFE,0x0F,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0xE0,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"4",20*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0x03,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0x04,0x00,0xF4,0x00,0x8C,0x01,0x04,0x03,0x00,0x03,0x00,0x03,0x06,0x03,0x06,0x03,0x82,0x01,0x84,0x01,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"5",21*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x01,0x18,0x03,0x0C,0x03,0x0C,0x00,0x04,0x00,0x06,0x00,0xE6,0x01,0x16,0x03,0x0E,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x04,0x06,0x0C,0x02,0x18,0x03,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"6",22*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x07,0x0C,0x06,0x04,0x02,0x04,0x01,0x00,0x01,0x00,0x01,0x80,0x00,0x80,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"7",23*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x01,0x0C,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x0C,0x02,0x1C,0x03,0xF0,0x00,0xC8,0x01,0x0C,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x0C,0x03,0xF0,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"8",24*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x0C,0x01,0x0C,0x03,0x06,0x02,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x07,0x8C,0x06,0x78,0x06,0x00,0x06,0x00,0x03,0x00,0x03,0x0C,0x01,0x8C,0x01,0x78,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"9",25*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*":",26*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x40,0x00,0x20,0x00,0x20,0x00},/*";",27*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x02,0x00,0x01,0x80,0x00,0x40,0x00,0x20,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x08,0x00,0x10,0x00,0x20,0x00,0x40,0x00,0x80,0x00,0x00,0x01,0x00,0x02,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00},/*"<",28*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x07,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"=",29*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x08,0x00,0x10,0x00,0x20,0x00,0x40,0x00,0x80,0x00,0x00,0x01,0x00,0x02,0x00,0x04,0x00,0x02,0x00,0x01,0x80,0x00,0x40,0x00,0x20,0x00,0x10,0x00,0x08,0x00,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*">",30*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x03,0x18,0x06,0x04,0x0C,0x04,0x0C,0x0C,0x0C,0x0C,0x0C,0x00,0x07,0x80,0x01,0x40,0x00,0x40,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0xE0,0x00,0xE0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"?",31*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x00,0x18,0x03,0x0C,0x02,0xCC,0x05,0x64,0x05,0x66,0x05,0xA6,0x05,0xB6,0x04,0xB6,0x04,0xB6,0x04,0xB6,0x04,0xB6,0x02,0xE4,0x01,0x0C,0x04,0x0C,0x02,0x18,0x03,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"@",32*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x50,0x00,0xD0,0x00,0x90,0x00,0x90,0x00,0x88,0x00,0x88,0x01,0x08,0x01,0xF8,0x01,0x04,0x03,0x04,0x03,0x04,0x02,0x02,0x02,0x02,0x06,0x0F,0x0F,0x00,0x00,0x00,0x00,0x00,0x00},/*"A",33*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x8C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x8C,0x01,0xFC,0x00,0x0C,0x03,0x0C,0x02,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x03,0xFE,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"B",34*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x03,0x18,0x03,0x0C,0x06,0x0C,0x04,0x04,0x04,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x04,0x0C,0x04,0x0C,0x02,0x18,0x03,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"C",35*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x8C,0x01,0x0C,0x03,0x0C,0x03,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x03,0x0C,0x03,0x8C,0x01,0x7F,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"D",36*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x03,0x06,0x03,0x06,0x04,0x06,0x04,0x06,0x00,0x86,0x00,0x86,0x00,0xFE,0x00,0x86,0x00,0x86,0x00,0x86,0x00,0x06,0x00,0x06,0x04,0x06,0x04,0x06,0x02,0xFF,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"E",37*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x03,0x06,0x03,0x06,0x04,0x06,0x04,0x06,0x00,0x86,0x00,0x86,0x00,0xFE,0x00,0x86,0x00,0x86,0x00,0x86,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"F",38*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x18,0x01,0x0C,0x02,0x0C,0x02,0x04,0x02,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0xC6,0x0F,0x06,0x03,0x06,0x03,0x0C,0x03,0x0C,0x03,0x18,0x03,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"G",39*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x0F,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0xFE,0x07,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x0F,0x0F,0x00,0x00,0x00,0x00,0x00,0x00},/*"H",40*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0x03,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xFC,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"I",41*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x07,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC0,0x00,0xC6,0x00,0x66,0x00,0x3C,0x00},/*"J",42*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xCF,0x03,0x86,0x01,0xC6,0x00,0x46,0x00,0x26,0x00,0x16,0x00,0x36,0x00,0x2E,0x00,0x6E,0x00,0x46,0x00,0xC6,0x00,0x86,0x00,0x86,0x01,0x06,0x01,0x06,0x03,0x8F,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"K",43*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1F,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x04,0x06,0x04,0x06,0x02,0xFF,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"L",44*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x07,0x07,0x86,0x03,0x86,0x03,0x8E,0x03,0x8E,0x03,0x4E,0x03,0x4E,0x03,0x4A,0x03,0x5A,0x03,0x5A,0x03,0x3A,0x03,0x32,0x03,0x32,0x03,0x32,0x03,0x12,0x03,0x87,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"M",45*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x8E,0x0F,0x0C,0x02,0x1C,0x02,0x1C,0x02,0x34,0x02,0x34,0x02,0x64,0x02,0x64,0x02,0x44,0x02,0xC4,0x02,0x84,0x02,0x84,0x03,0x84,0x03,0x04,0x03,0x04,0x03,0x1F,0x02,0x00,0x00,0x00,0x00,0x00,0x00},/*"N",46*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x98,0x01,0x0C,0x03,0x0C,0x02,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x0C,0x02,0x0C,0x03,0x98,0x01,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"O",47*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x06,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x86,0x03,0xFE,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x00,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"P",48*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x98,0x01,0x0C,0x03,0x0C,0x02,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x76,0x06,0x4C,0x02,0xCC,0x03,0x98,0x01,0xF0,0x00,0x80,0x07,0x00,0x03,0x00,0x00},/*"Q",49*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x01,0x06,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x03,0xFE,0x00,0x46,0x00,0xC6,0x00,0x86,0x00,0x86,0x01,0x06,0x03,0x06,0x03,0x06,0x06,0x0F,0x0E,0x00,0x00,0x00,0x00,0x00,0x00},/*"R",50*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF8,0x02,0x0C,0x03,0x06,0x02,0x06,0x02,0x06,0x00,0x0E,0x00,0x3C,0x00,0xF8,0x00,0xE0,0x03,0x80,0x03,0x00,0x07,0x02,0x06,0x02,0x06,0x06,0x06,0x0C,0x03,0xF0,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"S",51*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x07,0x62,0x04,0x61,0x08,0x61,0x08,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xF8,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"T",52*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1E,0x07,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x0C,0x02,0x18,0x01,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"U",53*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x07,0x06,0x02,0x04,0x01,0x04,0x01,0x0C,0x01,0x0C,0x01,0x88,0x00,0x88,0x00,0x98,0x00,0x98,0x00,0x50,0x00,0x50,0x00,0x70,0x00,0x30,0x00,0x20,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"V",54*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF7,0x0E,0x62,0x04,0x42,0x04,0x46,0x04,0x46,0x04,0x64,0x02,0x64,0x02,0xE4,0x02,0xE4,0x02,0x9C,0x02,0x9C,0x01,0x98,0x01,0x98,0x01,0x88,0x01,0x88,0x00,0x88,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"W",55*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9E,0x07,0x0C,0x01,0x08,0x01,0x18,0x01,0x90,0x00,0xB0,0x00,0x60,0x00,0x20,0x00,0x60,0x00,0x60,0x00,0xD0,0x00,0x90,0x00,0x88,0x01,0x08,0x01,0x04,0x03,0x8E,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"X",56*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0F,0x0F,0x06,0x04,0x04,0x02,0x0C,0x02,0x08,0x01,0x18,0x01,0xB8,0x00,0xB0,0x00,0x70,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xF8,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"Y",57*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0x07,0x0C,0x02,0x06,0x03,0x02,0x01,0x80,0x01,0x80,0x00,0x40,0x00,0x40,0x00,0x20,0x00,0x20,0x00,0x10,0x00,0x18,0x00,0x08,0x04,0x0C,0x04,0x04,0x02,0xFE,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"Z",58*/
{0x00,0x00,0x00,0x00,0xE0,0x03,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0x20,0x00,0xE0,0x03,0x00,0x00},/*"[",59*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x04,0x00,0x08,0x00,0x08,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x20,0x00,0x20,0x00,0x40,0x00,0x40,0x00,0xC0,0x00,0x80,0x00,0x80,0x00,0x00,0x01,0x00,0x01,0x00,0x02,0x00,0x02,0x00,0x02,0x00,0x04},/*"\",60*/
{0x00,0x00,0x00,0x00,0x7C,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x7C,0x00,0x00,0x00},/*"]",61*/
{0x00,0x00,0x60,0x00,0x90,0x00,0x08,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"^",62*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x0F},/*"_",63*/
{0x00,0x00,0x00,0x00,0x18,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"`",64*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x01,0x0C,0x03,0x0C,0x03,0x00,0x03,0xE0,0x03,0x1C,0x03,0x0E,0x03,0x06,0x03,0x06,0x03,0x8E,0x0B,0x7C,0x0E,0x00,0x00,0x00,0x00,0x00,0x00},/*"a",65*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x0E,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0xCC,0x01,0x3C,0x03,0x1C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x02,0x1C,0x03,0xE4,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"b",66*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x8C,0x01,0x8C,0x01,0x86,0x01,0x06,0x00,0x06,0x00,0x06,0x00,0x06,0x02,0x0C,0x02,0x0C,0x01,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"c",67*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x02,0xC0,0x03,0x00,0x03,0x00,0x03,0x00,0x03,0x00,0x03,0x78,0x03,0x8C,0x03,0x0C,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x04,0x03,0x8C,0x07,0x78,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"d",68*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE0,0x01,0x18,0x03,0x08,0x02,0x0C,0x06,0x0C,0x06,0xFC,0x07,0x0C,0x00,0x0C,0x00,0x18,0x04,0x18,0x02,0xE0,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"e",69*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x03,0x60,0x06,0x30,0x06,0x30,0x00,0x30,0x00,0xFE,0x01,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"f",70*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x07,0xD8,0x06,0x8C,0x01,0x8C,0x01,0x8C,0x01,0x98,0x01,0xF8,0x00,0x0C,0x00,0xFC,0x00,0xCC,0x03,0x06,0x03,0x06,0x03,0x8E,0x03,0xF8,0x00},/*"g",71*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x0E,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0xEC,0x01,0x1C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x9E,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"h",72*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x00,0x60,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x7C,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xFC,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"i",73*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x01,0xC0,0x01,0x00,0x00,0x00,0x00,0x00,0x01,0xF0,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0x80,0x01,0xCC,0x00,0x7C,0x00},/*"j",74*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x0E,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0x0C,0x00,0x8C,0x03,0x8C,0x00,0x8C,0x00,0x4C,0x00,0x6C,0x00,0x5C,0x00,0x8C,0x00,0x8C,0x01,0x0C,0x01,0x0C,0x03,0x9E,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"k",75*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x00,0x7C,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0xFC,0x03,0x00,0x00,0x00,0x00,0x00,0x00},/*"l",76*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x37,0x07,0xEE,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0x66,0x06,0xFF,0x0F,0x00,0x00,0x00,0x00,0x00,0x00},/*"m",77*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEE,0x01,0x1C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x9E,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"n",78*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x00,0x98,0x01,0x0C,0x03,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x06,0x0C,0x03,0x0C,0x03,0xF0,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"o",79*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEE,0x01,0x1C,0x03,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x06,0x0C,0x03,0x1C,0x03,0xEC,0x01,0x0C,0x00,0x0C,0x00,0x3E,0x00},/*"p",80*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x02,0x8C,0x03,0x0C,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x06,0x03,0x04,0x03,0x8C,0x03,0x78,0x03,0x00,0x03,0x00,0x03,0xC0,0x07},/*"q",81*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9F,0x03,0x58,0x06,0x38,0x06,0x18,0x00,0x18,0x00,0x18,0x00,0x18,0x00,0x18,0x00,0x18,0x00,0x18,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"r",82*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0x03,0x1C,0x03,0x0C,0x02,0x0C,0x02,0x38,0x00,0xF0,0x00,0xC0,0x03,0x04,0x03,0x04,0x03,0x8C,0x03,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"s",83*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0x00,0x20,0x00,0x30,0x00,0x30,0x00,0xFE,0x01,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x00,0x30,0x02,0x30,0x02,0xE0,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"t",84*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x02,0x8E,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x0C,0x03,0x9C,0x07,0x78,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"u",85*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1E,0x07,0x0C,0x02,0x08,0x01,0x08,0x01,0x18,0x01,0x90,0x00,0xB0,0x00,0xB0,0x00,0x60,0x00,0x60,0x00,0x20,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"v",86*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xF7,0x0E,0x62,0x04,0x46,0x04,0x64,0x02,0x64,0x02,0xEC,0x02,0x9C,0x01,0x98,0x01,0x98,0x01,0x98,0x01,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"w",87*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xBC,0x07,0x18,0x01,0x10,0x01,0xB0,0x00,0x60,0x00,0x60,0x00,0xE0,0x00,0x90,0x00,0x08,0x01,0x08,0x03,0x9E,0x07,0x00,0x00,0x00,0x00,0x00,0x00},/*"x",88*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x9E,0x07,0x08,0x01,0x08,0x01,0x08,0x01,0x90,0x00,0x90,0x00,0xB0,0x00,0x60,0x00,0x60,0x00,0x60,0x00,0x20,0x00,0x20,0x00,0x24,0x00,0x1C,0x00},/*"y",89*/
{0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFC,0x01,0x84,0x01,0xC4,0x00,0x44,0x00,0x60,0x00,0x20,0x00,0x30,0x00,0x18,0x02,0x08,0x02,0x0C,0x03,0xFC,0x01,0x00,0x00,0x00,0x00,0x00,0x00},/*"z",90*/
{0x00,0x00,0x00,0x00,0x00,0x03,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x40,0x00,0x20,0x00,0x40,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x00,0x03,0x00,0x00},/*"{",91*/
{0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00,0x40,0x00},/*"|",92*/
{0x00,0x00,0x00,0x00,0x0C,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x20,0x00,0x40,0x00,0x20,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x10,0x00,0x0C,0x00,0x00,0x00},/*"}",93*/
{0x00,0x00,0x1C,0x00,0x22,0x04,0xC2,0x04,0x80,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00},/*"~",94*/

};

typedef struct 
{
	unsigned char Index[2];	
	unsigned char Msk[24];
}typFNT_GB12; 

const typFNT_GB12 tfont12[]={
"输",0x84,0x00,0x44,0x01,0x2F,0x02,0xD2,0x05,0x05,0x00,0x7F,0x04,0x54,0x05,0x7C,0x05,
0x57,0x05,0x74,0x05,0x54,0x04,0x54,0x06,/*"输",0*/
"出",0x20,0x00,0x22,0x02,0x22,0x02,0x22,0x02,0xFE,0x03,0x20,0x00,0x20,0x00,0x21,0x04,
0x21,0x04,0x21,0x04,0xFF,0x07,0x00,0x04,/*"出",1*/
"状",0x84,0x00,0x84,0x02,0x85,0x04,0x86,0x00,0xF4,0x07,0x84,0x00,0x44,0x01,0x46,0x01,
0x45,0x01,0x24,0x02,0x24,0x02,0x14,0x04,/*"状",2*/
"态",0x20,0x00,0x20,0x00,0xFF,0x07,0x50,0x00,0x88,0x00,0x24,0x01,0x43,0x06,0x20,0x00,
0x4A,0x02,0x4A,0x04,0x09,0x05,0xF0,0x01,/*"态",3*/
"频",0xC8,0x07,0x3A,0x01,0x8A,0x00,0xCA,0x07,0x7F,0x04,0x48,0x05,0x4A,0x05,0x6A,0x05,
0x51,0x05,0x08,0x01,0x84,0x02,0x43,0x04,/*"频",4*/
"率",0x20,0x00,0xFF,0x07,0x10,0x00,0x8A,0x02,0x7C,0x01,0x20,0x00,0x54,0x01,0xFA,0x02,
0x20,0x00,0xFF,0x07,0x20,0x00,0x20,0x00,/*"率",5*/
"占",0x20,0x00,0x20,0x00,0x20,0x00,0xE0,0x07,0x20,0x00,0x20,0x00,0xFE,0x03,0x02,0x02,
0x02,0x02,0x02,0x02,0xFE,0x03,0x02,0x02,/*"占",6*/
"空",0x10,0x00,0x20,0x00,0xFF,0x07,0x89,0x04,0x04,0x01,0x02,0x02,0x00,0x00,0xFE,0x03,
0x20,0x00,0x20,0x00,0x20,0x00,0xFF,0x07,/*"空",7*/
"比",0x42,0x00,0x42,0x00,0x42,0x04,0x42,0x02,0x5E,0x01,0xC2,0x00,0x42,0x00,0x42,0x00,
0x52,0x00,0x4A,0x04,0x46,0x04,0x82,0x07,/*"比",8*/
"输",0x84,0x00,0x44,0x01,0x2F,0x02,0xD2,0x05,0x05,0x00,0x7F,0x04,0x54,0x05,0x7C,0x05,
0x57,0x05,0x74,0x05,0x54,0x04,0x54,0x06,/*"输",9*/
"入",0x0C,0x00,0x10,0x00,0x20,0x00,0x20,0x00,0x50,0x00,0x50,0x00,0x50,0x00,0x88,0x00,
0x88,0x00,0x04,0x01,0x02,0x02,0x01,0x04,/*"入",1*/
"幅",0xC4,0x07,0x04,0x00,0xDF,0x07,0x55,0x04,0xD5,0x07,0x15,0x00,0xD5,0x07,0x55,0x05,
0xDD,0x07,0x44,0x05,0xC4,0x07,0x44,0x04,/*"幅",2*/
"值",0x44,0x00,0xF4,0x07,0x42,0x00,0xF2,0x03,0x13,0x02,0xF2,0x03,0x12,0x02,0xF2,0x03,
0x12,0x02,0xF2,0x03,0x12,0x02,0xFA,0x07,/*"值",3*/
};


typedef struct 
{
	unsigned char Index[2];	
	unsigned char Msk[32];
}typFNT_GB16; 

const typFNT_GB16 tfont16[]={
	
"简",0x04,0x02,0xFC,0x7E,0x12,0x09,0xA1,0x10,0x08,0x00,0xD0,0x1F,0x04,0x10,0xE4,0x13,
0x24,0x12,0x24,0x12,0xE4,0x13,0x24,0x12,0x24,0x12,0xE4,0x13,0x04,0x10,0x04,0x18,/*"简",0*/
"易",0xF0,0x0F,0x10,0x08,0x10,0x08,0xF0,0x0F,0x10,0x08,0x10,0x08,0xF0,0x0F,0x20,0x00,
0x10,0x00,0xF8,0x3F,0x44,0x22,0x42,0x22,0x20,0x21,0x10,0x21,0x88,0x14,0x40,0x08,/*"易",1*/
"示",0x00,0x00,0xFC,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x7F,0x80,0x00,
0x80,0x00,0x88,0x08,0x88,0x10,0x84,0x20,0x82,0x40,0x81,0x40,0xA0,0x00,0x40,0x00,/*"示",2*/
"波",0x00,0x04,0x04,0x04,0x08,0x04,0xC8,0x7F,0x41,0x44,0x42,0x24,0x52,0x04,0xD0,0x3F,
0x48,0x21,0x48,0x11,0x47,0x12,0x44,0x0A,0x44,0x04,0x24,0x0A,0x24,0x11,0x90,0x60,/*"波",3*/
"器",0x00,0x00,0x7C,0x3E,0x44,0x22,0x44,0x22,0x7C,0x3E,0x80,0x04,0x80,0x08,0xFF,0x7F,
0x40,0x01,0x30,0x06,0x0C,0x18,0x03,0x60,0x7C,0x3E,0x44,0x22,0x44,0x22,0x7C,0x3E,/*"器",4*/
"打",0x08,0x00,0x08,0x00,0xC8,0x7F,0x08,0x04,0x3F,0x04,0x08,0x04,0x08,0x04,0x28,0x04,
0x18,0x04,0x0C,0x04,0x0B,0x04,0x08,0x04,0x08,0x04,0x08,0x04,0x0A,0x05,0x04,0x02,/*"打",0*/
"开",0x00,0x00,0xFE,0x3F,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x04,0xFF,0x7F,
0x10,0x04,0x10,0x04,0x10,0x04,0x10,0x04,0x08,0x04,0x08,0x04,0x04,0x04,0x02,0x04,/*"开",1*/
"关",0x08,0x08,0x10,0x08,0x10,0x04,0x00,0x00,0xFC,0x1F,0x80,0x00,0x80,0x00,0x80,0x00,
0xFF,0x7F,0x80,0x00,0x40,0x01,0x40,0x01,0x20,0x02,0x10,0x04,0x0C,0x18,0x03,0x60,/*"关",2*/
"闭",0x04,0x00,0xE8,0x3F,0x00,0x20,0x02,0x21,0x02,0x21,0xFA,0x2F,0x02,0x21,0x82,0x21,
0x42,0x21,0x22,0x21,0x12,0x21,0x0A,0x21,0x42,0x21,0x82,0x20,0x02,0x28,0x02,0x10,/*"闭",3*/
"模",0x88,0x08,0x88,0x08,0xE8,0x3F,0x88,0x08,0x3F,0x00,0xC8,0x1F,0x4C,0x10,0xDC,0x1F,
	0x6A,0x10,0xCA,0x1F,0x09,0x02,0xE8,0x3F,0x08,0x05,0x88,0x08,0x48,0x10,0x28,0x60,/*"模",0*/
"式",0x00,0x12,0x00,0x22,0x00,0x22,0x00,0x02,0xFF,0x7F,0x00,0x02,0x00,0x02,0x7C,0x02,
0x10,0x02,0x10,0x02,0x10,0x04,0x10,0x44,0xF0,0x48,0x1E,0x50,0x04,0x60,0x00,0x40,/*"式",0*/
"测",
0x00,0x20,0xE4,0x23,0x28,0x22,0x28,0x2A,0xA1,0x2A,0xA2,0x2A,0xA2,0x2A,0xA8,0x2A,0xA8,0x2A,0xA4,0x2A,0xA7,0x2A,0x84,0x20,0x44,0x21,0x44,0x22,0x24,0x28,0x10,0x10,/*"测",0*/
"电",
0x80,0x00,0x80,0x00,0x80,0x00,0xFC,0x1F,0x84,0x10,0x84,0x10,0x84,0x10,0xFC,0x1F,0x84,0x10,0x84,0x10,0x84,0x10,0xFC,0x1F,0x84,0x50,0x80,0x40,0x80,0x40,0x00,0x7F,/*"电",1*/
"阻",
0x00,0x00,0xBE,0x1F,0xA2,0x10,0x92,0x10,0x92,0x10,0x8A,0x1F,0x92,0x10,0x92,0x10,0xA2,0x10,0xA2,0x1F,0xA2,0x10,0x96,0x10,0x8A,0x10,0x82,0x10,0xE2,0x7F,0x02,0x00,/*"阻",2*/




};


typedef struct 
{
	unsigned char Index[2];	
	unsigned char Msk[72];
}typFNT_GB24;  

const typFNT_GB24 tfont24[]={
    
"简",0x00,0x00,0x00,0x20,0x40,0x00,0x60,0xC0,0x00,0x20,0x60,0x00,0xF0,0xEF,0x3F,0x98,
0x30,0x01,0x08,0x11,0x02,0x24,0x09,0x02,0xC0,0xFE,0x1F,0x80,0x00,0x08,0x30,0x00,
0x08,0x10,0xFE,0x08,0x10,0x42,0x08,0x10,0x42,0x08,0x10,0x42,0x08,0x10,0x7E,0x08,
0x10,0x42,0x08,0x10,0x42,0x08,0x10,0x7E,0x08,0x10,0x42,0x08,0x10,0x00,0x08,0x10,
0x80,0x09,0x10,0x00,0x0E,0x10,0x00,0x04,/*"简",0*/
"易",0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0xFF,0x03,0xC0,0x00,0x02,0xC0,0x00,0x02,0xC0,
0x00,0x02,0xC0,0xFF,0x03,0xC0,0x00,0x02,0xC0,0x00,0x02,0xC0,0xFF,0x03,0xC0,0x03,
0x02,0x80,0x01,0x00,0x80,0xFF,0x1F,0xC0,0x8C,0x18,0x20,0xC4,0x08,0x10,0x46,0x08,
0x08,0x63,0x08,0x80,0x21,0x08,0x40,0x30,0x0C,0x30,0x18,0x04,0x00,0x46,0x04,0x80,
0x81,0x07,0x60,0x00,0x01,0x00,0x00,0x00,/*"易",1*/
"示",0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x04,0xF0,0xFF,0x0F,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x20,0xFE,0xFF,0x3F,0x00,0x18,
0x00,0x00,0x18,0x00,0x80,0x98,0x00,0xC0,0x18,0x01,0xC0,0x18,0x02,0x60,0x18,0x04,
0x30,0x18,0x0C,0x10,0x18,0x18,0x08,0x18,0x30,0x04,0x18,0x10,0x82,0x1F,0x00,0x00,
0x0E,0x00,0x00,0x04,0x00,0x00,0x00,0x00,/*"示",2*/
"波",0x00,0x00,0x00,0x00,0xC0,0x00,0x10,0x80,0x00,0x30,0x80,0x00,0x20,0x80,0x00,0x00,
0xFF,0x3F,0x00,0x83,0x10,0x86,0x82,0x08,0x8C,0x82,0x00,0x48,0x82,0x00,0x48,0x82,
0x00,0x40,0xFE,0x1F,0x20,0x12,0x08,0x20,0x12,0x04,0x10,0x22,0x04,0x10,0x22,0x02,
0x1C,0x43,0x03,0x18,0x81,0x01,0x18,0xC1,0x01,0x98,0x60,0x06,0xD8,0x10,0x0C,0x58,
0x0C,0x78,0x20,0x03,0x00,0x00,0x00,0x00,/*"波",3*/
"器",0x00,0x00,0x00,0x00,0x00,0x00,0xF0,0xE3,0x0F,0x30,0x66,0x0C,0x30,0x66,0x0C,0x30,
0x66,0x0C,0x30,0x66,0x0C,0xF0,0xE7,0x0F,0x30,0xFE,0x0D,0x10,0x0C,0x13,0xFC,0xFF,
0x3F,0x00,0x42,0x00,0x00,0x81,0x00,0x80,0x00,0x01,0x60,0x00,0x0E,0xF0,0xE7,0x3F,
0x2C,0x26,0x0C,0x20,0x26,0x0C,0x20,0x26,0x0C,0x20,0x26,0x0C,0xE0,0xE7,0x0F,0x20,
0x26,0x0C,0x10,0x22,0x04,0x00,0x00,0x00,/*"器",4*/
};

#endif

取字模的方法

因为写入的地址是按照这样的来取的，所以你要是用的这个代码的话就按照这样来取字模

main.c

	TFT_Fill(0,0,106,128,BLACK);
	TFT_Fill(106,0,160,128,GRAY);
	TFT_GUI_Start();

可以启动了

这样刷新率似乎有慢

现在只要对tft_init.h略作修改即可

tft_init.h

static void SPI0_Write(uint8_t TxData)
{
    //等待发送缓冲区空闲
while(__HAL_SPI_GET_FLAG(&hspi1, SPI_FLAG_TXE) == RESET){}
    TFT_SPIx->DR=TxData; //通过外设SPIx发送一个byte  数据
    TFT_SPIx->SR&=(1<<0);
}

void TFT_WR_DATA8(uint8_t data)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
    
    SPI0_Write(data);
//	HAL_SPI_Transmit(&hspi1,&data,1,0xfff);
//     HAL_SPI_Transmit_DMA(&hspi1, &data, 1);
    SPI_TFT_CS_HIGH();     //拉高片选信号
}
/*
*   函数内容：TFT发送2个字节数据
*   函数参数：无
*   返回值：无
*/
void TFT_WR_DATA(uint16_t data)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
//    
    SPI0_Write(data>>8);
//		TFT_WR_DATA8(data>>8);
//	TFT_WR_DATA8(data);
	SPI0_Write(data);
//	uint8_t data_high = (uint8_t)(data >> 8);  // 获取高8位数据

//HAL_SPI_Transmit(&hspi1, &data_high, sizeof(data_high), 0xfff);  // 发送高8位数据

SPI_TFT_CS_HIGH();
}

/*
*   函数内容：TFT发送命令数据
*   函数参数：无
*   返回值：无
*/
void TFT_WR_REG(uint8_t reg)
{
    SPI_TFT_CS_LOW();   //拉低片选信号
    TFT_DC_LOW();       //拉低片选信号
    
   HAL_SPI_Transmit(&hspi1,&reg,sizeof(reg),0xfff);
//	 HAL_SPI_Transmit_DMA(&hspi1,&reg,sizeof(reg));
//    TFT_WR_DATA8(reg);
    TFT_DC_HIGH();     //拉高命令信号
    TFT_DC_HIGH();;     //拉高片选信号
}

再次启动

现在刷新就特别快了

没事干的yue
关注
SPI_TFT屏幕驱动程序
12-07
C++和C的混合代码，为了方便继承管理，条理更加清晰，Eclipse工程，实现了驱动SPI接口的LCD屏幕包含常用的显示和绘图函数
TFT彩屏（硬件SPI）
04-07
TFT彩屏（硬件SPI）,初学者。采用硬件SPI驱动9341屏。
【GD32】06 - SPI （含ST7735S TFT-LCD屏幕驱动）
最新发布
m0_63235356的博客
06-03 1607
接下来我们要开启引脚复用，SPI一共是四个引脚，MISO，MOSI，SS，SCK，其中SS一般来说我们不让他硬件控制，通常我们会另外软件控制，因为硬件SPI的SS是固定死的，这样可能会和我们其他要用的引脚冲突，而且使用硬件SPI就是为了速度更快，而SS软件另外控制并不会影响多少速度，因此我们就算使用硬件SPI，也会让SS引脚使用软件控制。有了SPI，我们就可以直接封装ST7735S的驱动了，具体ST7735S的指令什么的我就不在这边啰嗦了，之前的文章有小小地介绍一下，文章链接在本文的开头。
一起玩儿物联网人工智能小车（ESP32）——59. 基于TFT_eSPI库的1.3寸SPI彩色显示屏的使用（ST7789）
一起玩儿科技
02-11 2068
摘要：本文是TFT液晶屏的基本知识和TFT_eSPI库的简单介绍
STM32+CubeMax驱动1.3寸TFT屏幕
qq_56089182的博客
08-17 2146
使用STM32F103C8T6驱动1.3寸TFT屏幕的驱动代码用法这里使用的开发板和屏幕都来自某宝店家大越创新。
基于STM32f103c6t6芯片，使用HAl库的硬件SPI+DMA的驱动ST7735s芯片的keil工程包含CubeMX工程
04-23
2、驱动ST7735s芯片的1.8寸spi屏幕 3、资源包含了CubeMX工程文件和对应的Keil工程 4、配置好了硬件SPI以及DMA 5、注意：工程内配置了屏幕的按键，但是并未使用 6、工程内已经配置好了串口2，并且配置了对应的DMA，...
STM32F407HAL库模拟SPI驱动1.8寸TFT（ST7735）屏幕
08-06
在本文中，我们将深入探讨如何使用STM32F407微控制器的HAL库来模拟SPI接口，以驱动1.8英寸的TFT（ST7735）屏幕。STM32F407是意法半导体（STMicroelectronics）推出的一款基于ARM Cortex-M4内核的高性能MCU，它具有...
STM32F103C8T6HAL库模拟SPI ST7735屏幕驱动
04-14
描述中提到"屏幕驱动"，意味着这个工程包含了ST7735的初始化代码和控制函数，可以设置屏幕的分辨率、颜色模式以及进行数据传输等操作。 "多次测试，完美运行"表明该工程已经经过充分验证，可以在实际应用中稳定工作...
Proteus 仿真STM32F103C8T6 HAL库硬件SPI驱动ST7735R TFT LCD
07-27
在本项目中，我们主要探讨如何使用Proteus仿真软件来模拟STM32F103C8T6微控制器通过HAL库驱动ST7735R TFT LCD显示器的工作过程。这个过程涉及到嵌入式系统设计、微控制器编程以及硬件接口技术等多个知识点。 首先，...
stm32f103c8t6软件spi驱动st7735s屏幕
09-25
总结，STM32F103C8T6通过软件SPI驱动ST7735S屏幕涉及到微控制器的GPIO操作、SPI通信协议的理解、LCD控制器的初始化以及屏幕的像素数据传输。这个过程需要对嵌入式系统和微控制器有深入的了解，同时也需要一定的编程...
嵌入式开发-STM32硬件SPI驱动TFT屏
深圳五月花--老李的森林
12-12 4111
现在的TFT屏幕已经很便宜了，65536色屏幕，2.8英寸，分辨率320X240的液晶屏才20元，我为了图省事，多配了一个转接板12元，共32元包邮到家，真是香。 上面这个是这次用到的2.8寸TFT屏幕（20元），下面的是0.96寸OLED屏（10元），可见尺寸的巨大差别。当然OLED屏的优势是省电，在手持设备上是首选。 这个屏幕是SPI接口，最少4线驱动，分别是MOSI数据，CLK时钟，CS片选，DC数据/指令切换，还有2根线可选，是RESET和背光，复位可以用电阻电容上电时拉一下跳变即可，背光可以一直接
（六）DSP28335基础教程——SPI通信实验（TFT显示控制）
weixin_46556696的博客
01-02 1万+
0 前言 哈哈哈这段时间一口气录了三篇论文，其中两篇英文，一篇中文，舒服啊。然后这几天刚好忙完赶紧来补个例程！ 这个TFT例程折腾了我两天，网上找不到这个DSP的例子，只有STMS32的。所以我参考着中景园给出的原厂STM32例程和数据手册，历经千辛万苦，最后终于调通了程序。 为了帮助大家避免走弯路，我讲下硬件部分、软件部分和实验效果。这次工程代码就不全部贴上来了，要的可以直接找我哈。 1 硬件部分 参考中景园ILI9341的TFT数据手册，一共有8个管脚定义，分别如图1所示。其中VCC电压为3.3V。 图
NanoPi NEO Air使用十一：编写SPI驱动点亮TFT屏幕，ST7789V
qlexcel的专栏
10-27 3951
开发板引出来了spi0 本节用spi0驱动一个spi接口的屏幕，屏幕如下： 240x240分辨率，1.3寸，主控为ST7789。 与开发板的引脚连接确定如下： 功能 IO GND Pin6 5V Pin2 LCD_RESET Pin7-PG11 LCD_DC Pin22-PA1 SPICLK Pin23-PC2 SPIMOSI Pin19-PC0 修改设备树 spi0节点定义在/home/ql/linux/H3/linux/arch/arm/boot/dts/s
16.【linux驱动】spi驱动TFT液晶屏
柏鑫的博客
06-22 1728
代码
STM32HAL库使用SPI驱动1.44寸TFTLCD
热门推荐
geekYatao
03-01 2万+
  关于STM32F4单片机，使用HAL库自带的SPI，驱动TFTLCD屏幕的资料网上好像不太多，正好最近我做了这项工作，把成果分享给大家。我的代码实现了这些功能：任意坐标画点，指定首尾坐标画线，画方框，指定区域显示彩图，显示16* 16或者12* 12的汉字、ASCII码，并附带ASCII码表与少量的汉字字库。 硬件设计   屏幕选择：使用了一款低成本十六位彩屏，只要十块钱。链接   厂家看到...
27 在H5上实现spi-tft屏的简单驱动
jklinux的博客
12-05 4291
屏的购买链接:https://item.taobao.com/item.htm?spm=a1z10.5-c-s.w4002-16248799892.67.1b6f9109XnyTYo&id=520967019281内核里设备树关于spi屏的描述:&spi1 { #address-cells = <1>; #size-cells = <0>; status = "okay";
(ESP32学习13)驱动TFTLCD（SPI接口）
ailta的博客
06-08 1万+
本篇博文教大家ESP32 驱动TFT（SPI驱动），本文给大家的库直接适用于2寸（240*320）的SPI-TFT，但实际上这种驱动移植适用于所有的SPI驱动的TFT屏幕，底层代码把LCD初始化里面的寄存器参数改一改就适用了(这些寄存器参数在你买的屏幕的官方驱动里面有) 首先我们要知道我们要把移植的代码写在什么地方 这就是我们的代码要移植到的地方 看看驱动效果 直接给大家上代码，由于我们使用的是SPI，不受IO限制，我在底层写了一个IO绑定函数(lcd_io_set)，我们直接用这个函数把我们要连接的
小熊派使SPI驱动TFT-LCD（ST7789）显示试验
果果小师弟的博客
04-11 4727
学习SPI外设驱动LCD屏幕没有必要手写驱动，学习这部分代码的目的是为了了解TFT-LCD的工作原理，每个像素点是如何显示的，不要花过多的精力在弄明白每个命令的意思，建议基于本驱动，学习一下打点，画线算法，画圆算法，画多边形算法等等，还可以学习显示英文字符，中文字符，最后还可以移植STemwin显示界面等等好玩的东西~ 1. 准备工作 硬件准备 开发板 首先需要准备一个开发板，这里我准备的是STM32L4的开发板（BearPi）： LCD屏幕 小熊派开发板板载LCD屏幕大小1.3寸，分辨率240*240
hal库硬件SPI驱动LCD屏幕
05-17
以下是使用HAL库实现硬件SPI驱动LCD屏幕的大致步骤： 1. 配置SPI接口：使用HAL_SPI_Init()函数初始化SPI接口，并设置相应的时钟极性、相位、数据位、帧格式等参数； 2. 配置GPIO引脚：使用HAL_GPIO_Init()函数初始化...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值