Steps to perform for Rolling Forward a Physical Standby Database using RMAN Incremental Backup. (文档

APPLIES TO:

Oracle Database - Enterprise Edition - Version 10.2.0.1 to 12.1.0.2 [Release 10.2 to 12.1]
Information in this document applies to any platform.
Checked for relevance on 21-AUG-2015

GOAL

The steps in this section can used to resolve problems of missing or corrupted archive log file, an unresolveable archive gap, or need to roll standby forward in time without applying a large number of archivelog files.  

SOLUTION

 

Note:
If you use 'DataGuard Broker', then it should be stopped before starting with step 1 and re-started again when all steps finished.

1) Stop the managed recovery process (MRP) on the STANDBY database

SQL> ALTER DATABASE RECOVER MANAGED STANDBY DATABASE CANCEL;

 

Note:  For the remaining steps, the standby database must be in a MOUNT state.  

2) Determine the SCN of the STANDBY database.

On the standby database, find the SCN which will be used for the incremental backup at the primary database:

You need to use the 'lowest SCN' from the queries below:


SQL> SELECT CURRENT_SCN FROM V$DATABASE;

CURRENT_SCN
--------------
3164433 


SQL> select min(checkpoint_change#) from v$datafile_header 
where file# not in (select file# from v$datafile where enabled = 'READ ONLY');

MIN(F.FHSCN)
----------------
3162298


You need to use the 'lowest SCN' from the queries, in this example is SCN: 3162298.  Therefore, From the above you need to backup from SCN 3162298

3) Take an incremental backup of the PRIMARY database

In RMAN, connect to the primary database and create an incremental backup from the SCN derived in the previous step:

RMAN> BACKUP INCREMENTAL FROM SCN 3162298 DATABASE FORMAT '/tmp/ForStandby_%U' tag 'FORSTANDBY';

4) Transfer all backup sets to STANDBY server

All backups created by step #3 must be transferred from the primary to the standby system.  If the backup is written to NFS device, this step can be skipped.  

scp /tmp/ForStandby_* standby:/tmp

5) Catalog the backups in STANDBY controlfile.

In order for the standby database to know about the backups, catalog the backup pieces on the STANDBY database.  

RMAN> CATALOG START WITH '/tmp/ForStandby'; 

using target database control file instead of recovery catalog 
searching for all files that match the pattern /tmp/ForStandby 

List of Files Unknown to the Database 
===================================== 
File Name: /tmp/ForStandby_2lkglss4_1_1 
File Name: /tmp/ForStandby_2mkglst8_1_1 

Do you really want to catalog the above files (enter YES or NO)? YES 
cataloging files... 
cataloging done 

List of Cataloged Files 
======================= 
File Name: /tmp/ForStandby_2lkglss4_1_1 
File Name: /tmp/ForStandby_2mkglst8_1_1

6) Recover the STANDBY database with the cataloged incremental backup:

RMAN> RECOVER DATABASE NOREDO; 

starting recover at 03-JUN-09 
allocated channel: ORA_DISK_1 
channel ORA_DISK_1: sid=28 devtype=DISK 
channel ORA_DISK_1: starting incremental datafile backupset restore 
channel ORA_DISK_1: specifying datafile(s) to restore from backup set 
destination for restore of datafile 00001: +DATA/mystd/datafile/system.297.688213333 
destination for restore of datafile 00002: +DATA/mystd/datafile/undotbs1.268.688213335 
destination for restore of datafile 00003: +DATA/mystd/datafile/sysaux.267.688213333 
channel ORA_DISK_1: reading from backup piece /tmp/ForStandby_2lkglss4_1_1 
channel ORA_DISK_1: restored backup piece 1 
piece handle=/tmp/ForStandby_2lkglss4_1_1 tag=FORSTANDBY 
channel ORA_DISK_1: restore complete, elapsed time: 00:00:02 
Finished recover at 03-JUN-09

7) In RMAN, connect to the PRIMARY database and create a standby control file backup:

RMAN> BACKUP CURRENT CONTROLFILE FOR STANDBY FORMAT '/tmp/ForStandbyCTRL.bck';

8) Copy the standby control file backup to the STANDBY system. 

scp /tmp/ForStandbyCTRL.bck standby:/tmp

9) Capture datafile information in STANDBY database.

We now need to refresh the standby controlfile from primary controlfile (for standby) backup. However, since the datafile names are likely different than primary, let's save the name of datafiles on standby first, which we can refer after restoring controlfile from primary backup to verify if there is any discrepancy. Run below query from Standby and save results for further use.

spool datafile_names_step8.txt
set lines 200
col name format a60
select file#, name from v$datafile order by file# ;
spool off

10) From RMAN, connect to STANDBY database and restore the standby control file:

RMAN> SHUTDOWN IMMEDIATE ;
RMAN> STARTUP NOMOUNT; 
RMAN> RESTORE STANDBY CONTROLFILE FROM '/tmp/ForStandbyCTRL.bck'; 

Starting restore at 03-JUN-09 
using target database control file instead of recovery catalog 
allocated channel: ORA_DISK_1 
channel ORA_DISK_1: sid=36 devtype=DISK 

channel ORA_DISK_1: restoring control file 
channel ORA_DISK_1: restore complete, elapsed time: 00:00:07 
output filename=+DATA/mystd/controlfile/current.257.688583989 
Finished restore at 03-JUN-09

11) Shut down the STANDBY database and startup mount:

RMAN> SHUTDOWN; 
RMAN> STARTUP MOUNT;

12) Catalog datafiles in STANDBY if location/name of datafiles is different

Since the controlfile is restored from PRIMARY the datafile locations in STANDBY controlfile will be same as PRIMARY database, if the directory structure is different between the standby and primary or you are using Oracle managed file names, catalog the datafiles in STANDBY will do the necessary rename operations.  If the primary and standby have identical structure and datafile names, this step can be skipped.

Perform the below step  in STANDBY for each diskgroup where the datafile directory structure between primary and standby are different.

RMAN> CATALOG START WITH '+DATA/mystd/datafile/'; 

List of Files Unknown to the Database 
===================================== 
File Name: +data/mystd/DATAFILE/SYSTEM.309.685535773 
File Name: +data/mystd/DATAFILE/SYSAUX.301.685535773 
File Name: +data/mystd/DATAFILE/UNDOTBS1.302.685535775 
File Name: +data/mystd/DATAFILE/SYSTEM.297.688213333 
File Name: +data/mystd/DATAFILE/SYSAUX.267.688213333 
File Name: +data/mystd/DATAFILE/UNDOTBS1.268.688213335 

Do you really want to catalog the above files (enter YES or NO)? YES 
cataloging files... 
cataloging done 

List of Cataloged Files 
======================= 
File Name: +data/mystd/DATAFILE/SYSTEM.297.688213333 
File Name: +data/mystd/DATAFILE/SYSAUX.267.688213333 
File Name: +data/mystd/DATAFILE/UNDOTBS1.268.688213335

If any datafiles have been added to Primary AFTER scn 3162298 they will also have to be restored to the standby host (see Note 1531031.1 Steps to perform for Rolling forward a standby database using RMAN incremental backup when datafile is added to primary) and cataloged as shown above before doing the switch.   

To determine if any files have been added to Primary since the standby current scn:

SQL>SELECT FILE#, NAME FROM V$DATAFILE WHERE CREATION_CHANGE# > 3162298

If the above query returns with 0 zero rows, you can switch the datafiles. This will rename the datafiles to its correct name at the standby site:

RMAN> SWITCH DATABASE TO COPY; 

datafile 1 switched to datafile copy "+DATA/mystd/datafile/system.297.688213333" 
datafile 2 switched to datafile copy "+DATA/mystd/datafile/undotbs1.268.688213335" 
datafile 3 switched to datafile copy "+DATA/mystd/datafile/sysaux.267.688213333"

 Note:

a) At this point, you can compare the query output from step 9 for any discrepancy (other than newly added datafiles) to ensure we have all the datafiles added in standby.

b) run the queries from step 2 again to confirm that the incremental apply has moved the datafiles forward. The SCN should now be bigger than its initial values.

13) Configure the STANDBY database to use flashback (optional)

If the STANDBY database needs to be configured for FLASHBACK run the following commands:

SQL> ALTER DATABASE FLASHBACK OFF; 
SQL> ALTER DATABASE FLASHBACK ON;

 

NOTE:  This command may return the following:
   ORA-38788 More standby database recovery is needed
Depending on situation, this is expected.  Proceed with the remaining steps.

14) On STANDBY database, clear all standby redo log groups:

SQL> select GROUP# from v$logfile where TYPE='STANDBY' group by GROUP#;
SQL> ALTER DATABASE CLEAR LOGFILE GROUP 1; 
SQL> ALTER DATABASE CLEAR LOGFILE GROUP 2; 
SQL> ALTER DATABASE CLEAR LOGFILE GROUP 3;
....

15) On the STANDBY database, start the MRP

SQL> ALTER DATABASE RECOVER MANAGED STANDBY DATABASE DISCONNECT;

To resolve NOLOGGING operations only, see the online documentation, and Note 958181.1

  • 0
    点赞
  • 1
    收藏
    觉得还不错? 一键收藏
  • 0
    评论

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值