CC2640R2F程序移植——0.96OLED_IPS屏(ss7725驱动)

最新推荐文章于 2021-02-27 18:44:46 发布

liangjianneu

最新推荐文章于 2021-02-27 18:44:46 发布

阅读量802

点赞数 1

分类专栏： CC2640R2F 文章标签： CC2640R2F OLED SPI&amp;IIC SS7725 BLE5.0

本文链接：https://blog.csdn.net/qq_29916855/article/details/101764088

版权

CC2640R2F 专栏收录该内容

1 篇文章 0 订阅

订阅专栏

网盘链接：https://pan.baidu.com/s/1EuwoklE8m7Wlk-pOtC4Uzw
提取码：2333

一、引脚说明

1.1 接口定义

引脚	功能说明
GND	电源地
VCC	电源正 3.3~5V
D0	SPI接口时为SPI时钟线，IIC接口时为IIC时钟线
D1	SPI接口时为SPI数据线，IIC接口时为IIC数据线
RST	OLED复位，OLED在上电后需做一次复位
DC	SPI接口时SPI数据/命令选择脚，IIC接口时用来设置IIC地址
CS	片选

1.2 硬件连接

OLED引脚	CC2640R2F引脚
GND	GND
VCC	VCC
D0	IOID_9
D1	IOID_10
RST	IOID_4
DC	IOID_26
CS	IOID_5

1.3 总线协议
IO口软件模拟SPI

1.4 软件控制流程
①IO初始化。

②根据时序初始化LCD。

③显示。

二、移植文件

将 board_oled.c 、 board_oled.h 、oledfont.h三个文件拖拽至CCS工程的Application文件夹下

2.1 board_oled.c

/*********************************************************************
 * INCLUDES
 */
/* BIOS Header files */
#include <ti/sysbios/knl/Task.h>
#include <ti/sysbios/knl/Clock.h>
#include <ti/sysbios/knl/Semaphore.h>
#include <ti/sysbios/knl/Queue.h>
#include <ti/devices/cc26x0r2/driverlib/cpu.h>
/* Board Header files */
#include "Board.h"
#include "util.h"
#include "board_oled.h"
#include <string.h>
#include <stdio.h>
#include "oledfont.h"

u16 BACK_COLOR;   //背景色

/* Pin driver handle */
static PIN_Handle OLEDPinHandle = NULL;
static PIN_State OLEDPinState;

//-----------------OLED端口定义----------------
#define OLED_SCL        IOID_9      //SCLK  时钟 D0（SCLK）
#define OLED_SDA       IOID_10     //SDA   D1（MOSI） 数据
#define OLED_RST        IOID_4      //RES  hardware reset   复位
#define OLED_DC         IOID_26     //A0  H/L 命令数据选通端，H：数据，L:命令
#define OLED_CS         IOID_5     //CS

#define OLED_SCLK_Set()     PIN_setOutputValue(OLEDPinHandle, OLED_SCL, 1)
#define OLED_SCLK_Clr()     PIN_setOutputValue(OLEDPinHandle, OLED_SCL, 0)
#define OLED_SDIN_Set()     PIN_setOutputValue(OLEDPinHandle, OLED_SDA, 1)
#define OLED_SDIN_Clr()     PIN_setOutputValue(OLEDPinHandle, OLED_SDA, 0)
#define OLED_RST_Set()      PIN_setOutputValue(OLEDPinHandle, OLED_RST, 1)
#define OLED_RST_Clr()      PIN_setOutputValue(OLEDPinHandle, OLED_RST, 0)
#define OLED_DC_Set()       PIN_setOutputValue(OLEDPinHandle, OLED_DC, 1)
#define OLED_DC_Clr()       PIN_setOutputValue(OLEDPinHandle, OLED_DC, 0)
#define OLED_CS_Set()       PIN_setOutputValue(OLEDPinHandle, OLED_CS, 1)
#define OLED_CS_Clr()       PIN_setOutputValue(OLEDPinHandle, OLED_CS, 0)

/* Application OLED pin configuration table */
static PIN_Config OLEDPinTable[] = {
    OLED_SCL | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
    OLED_SDA | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
    OLED_RST | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
    OLED_DC  | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
    OLED_CS  | PIN_GPIO_OUTPUT_EN | PIN_GPIO_LOW | PIN_PUSHPULL | PIN_DRVSTR_MAX,
    PIN_TERMINATE       // Terminate list
};


/******************************************************************************
void delayMs(uint8_t time)
函数说明：2640cpu延时
入口数据：延时时间ms
返回值：  无
******************************************************************************/
extern void CPUdelay(uint32_t ui32Count);
void delayMs(uint8_t time)
{
    CPUdelay(12000 * time);
}

/******************************************************************************
函数说明：LCD样例测试程序
入口数据：无
返回值：  无
******************************************************************************/
void LCD_demo()
{
    	Lcd_Init();          //初始化OLED
        LCD_Clear(WHITE);
        BACK_COLOR=WHITE;
        LCD_ShowChinese(28,0,0,32,RED);   //中
        LCD_ShowChinese(60,0,1,32,RED);   //景
        LCD_ShowChinese(92,0,2,32,RED);   //园

        LCD_ShowChinese(20,40,0,16,RED);   //中
        LCD_ShowChinese(36,40,1,16,RED);   //景
        LCD_ShowChinese(52,40,2,16,RED);   //园
        LCD_ShowChinese(68,40,3,16,RED);  //电
        LCD_ShowChinese(84,40,4,16,RED);  //子
        LCD_ShowChinese(100,40,5,16,RED);  //科
        LCD_ShowChinese(116,40,6,16,RED);  //技
         
        LCD_ShowString(0,60,"0.96 TFT SPI",RED);
        LCD_ShowNum1(104,60,666.66,5,RED);//显示小数
}
/******************************************************************************
函数说明：LCD串行数据写入函数
入口数据：dat  要写入的串行数据
返回值：  无
******************************************************************************/
void LCD_Writ_Bus(u8 dat)
{
    u8 i;
    OLED_CS_Clr();
    for (i = 0; i<8; i++)
    {
        OLED_SCLK_Clr();
        if (dat & 0x80)
            OLED_SDIN_Set();
        else
            OLED_SDIN_Clr();
        OLED_SCLK_Set();
        dat <<= 1;
    }
    OLED_CS_Set();
}


/******************************************************************************
函数说明：LCD写入数据
入口数据：dat 写入的数据
返回值：  无
******************************************************************************/
void LCD_WR_DATA8(u8 dat)
{
    OLED_DC_Set();//写数据
    LCD_Writ_Bus(dat);
}


/******************************************************************************
函数说明：LCD写入数据
入口数据：dat 写入的数据
返回值：  无
******************************************************************************/
void LCD_WR_DATA(u16 dat)
{
    OLED_DC_Set();//写数据
    LCD_Writ_Bus(dat >> 8);
    LCD_Writ_Bus(dat);
}


/******************************************************************************
函数说明：LCD写入命令
入口数据：dat 写入的命令
返回值：  无
******************************************************************************/
void LCD_WR_REG(u8 dat)
{
    OLED_DC_Clr();//写命令
    LCD_Writ_Bus(dat);
}


/******************************************************************************
函数说明：设置起始和结束地址
入口数据：x1,x2 设置列的起始和结束地址
y1,y2 设置行的起始和结束地址
返回值：  无
******************************************************************************/
void LCD_Address_Set(u16 x1, u16 y1, u16 x2, u16 y2)
{
    if (USE_HORIZONTAL == 0)
    {
        LCD_WR_REG(0x2a);//列地址设置
        LCD_WR_DATA(x1 + 26);
        LCD_WR_DATA(x2 + 26);
        LCD_WR_REG(0x2b);//行地址设置
        LCD_WR_DATA(y1 + 1);
        LCD_WR_DATA(y2 + 1);
        LCD_WR_REG(0x2c);//储存器写
    }
    else if (USE_HORIZONTAL == 1)
    {
        LCD_WR_REG(0x2a);//列地址设置
        LCD_WR_DATA(x1 + 26);
        LCD_WR_DATA(x2 + 26);
        LCD_WR_REG(0x2b);//行地址设置
        LCD_WR_DATA(y1 + 1);
        LCD_WR_DATA(y2 + 1);
        LCD_WR_REG(0x2c);//储存器写
    }
    else if (USE_HORIZONTAL == 2)
    {
        LCD_WR_REG(0x2a);//列地址设置
        LCD_WR_DATA(x1 + 1);
        LCD_WR_DATA(x2 + 1);
        LCD_WR_REG(0x2b);//行地址设置
        LCD_WR_DATA(y1 + 26);
        LCD_WR_DATA(y2 + 26);
        LCD_WR_REG(0x2c);//储存器写
    }
    else
    {
        LCD_WR_REG(0x2a);//列地址设置
        LCD_WR_DATA(x1 + 1);
        LCD_WR_DATA(x2 + 1);
        LCD_WR_REG(0x2b);//行地址设置
        LCD_WR_DATA(y1 + 26);
        LCD_WR_DATA(y2 + 26);
        LCD_WR_REG(0x2c);//储存器写
    }
}


/******************************************************************************
函数说明：LCD初始化函数
入口数据：无
返回值：  无
******************************************************************************/
void Lcd_Init(void)
{
    /* Open LED pins */
    if(OLEDPinHandle == NULL)
    {
        OLEDPinHandle = PIN_open(&OLEDPinState, OLEDPinTable);
    }
    OLED_SCLK_Set();
    OLED_SDIN_Set();
    OLED_RST_Set();
    OLED_DC_Set();
    OLED_CS_Set();

    OLED_RST_Clr();
    delayMs(200);
    OLED_RST_Set();
    delayMs(200);
    OLED_SCLK_Set();
    delayMs(200);

    LCD_WR_REG(0x11);
    delayMs(100);

    LCD_WR_REG(0x21);

    LCD_WR_REG(0xB1);
    LCD_WR_DATA8(0x05);
    LCD_WR_DATA8(0x3A);
    LCD_WR_DATA8(0x3A);

    LCD_WR_REG(0xB2);
    LCD_WR_DATA8(0x05);
    LCD_WR_DATA8(0x3A);
    LCD_WR_DATA8(0x3A);

    LCD_WR_REG(0xB3);
    LCD_WR_DATA8(0x05);
    LCD_WR_DATA8(0x3A);
    LCD_WR_DATA8(0x3A);
    LCD_WR_DATA8(0x05);
    LCD_WR_DATA8(0x3A);
    LCD_WR_DATA8(0x3A);

    LCD_WR_REG(0xB4);
    LCD_WR_DATA8(0x03);

    LCD_WR_REG(0xC0);
    LCD_WR_DATA8(0x62);
    LCD_WR_DATA8(0x02);
    LCD_WR_DATA8(0x04);

    LCD_WR_REG(0xC1);
    LCD_WR_DATA8(0xC0);

    LCD_WR_REG(0xC2);
    LCD_WR_DATA8(0x0D);
    LCD_WR_DATA8(0x00);

    LCD_WR_REG(0xC3);
    LCD_WR_DATA8(0x8D);
    LCD_WR_DATA8(0x6A);

    LCD_WR_REG(0xC4);
    LCD_WR_DATA8(0x8D);
    LCD_WR_DATA8(0xEE);

    LCD_WR_REG(0xC5);  /*VCOM*/
    LCD_WR_DATA8(0x0E);

    LCD_WR_REG(0xE0);
    LCD_WR_DATA8(0x10);
    LCD_WR_DATA8(0x0E);
    LCD_WR_DATA8(0x02);
    LCD_WR_DATA8(0x03);
    LCD_WR_DATA8(0x0E);
    LCD_WR_DATA8(0x07);
    LCD_WR_DATA8(0x02);
    LCD_WR_DATA8(0x07);
    LCD_WR_DATA8(0x0A);
    LCD_WR_DATA8(0x12);
    LCD_WR_DATA8(0x27);
    LCD_WR_DATA8(0x37);
    LCD_WR_DATA8(0x00);
    LCD_WR_DATA8(0x0D);
    LCD_WR_DATA8(0x0E);
    LCD_WR_DATA8(0x10);

    LCD_WR_REG(0xE1);
    LCD_WR_DATA8(0x10);
    LCD_WR_DATA8(0x0E);
    LCD_WR_DATA8(0x03);
    LCD_WR_DATA8(0x03);
    LCD_WR_DATA8(0x0F);
    LCD_WR_DATA8(0x06);
    LCD_WR_DATA8(0x02);
    LCD_WR_DATA8(0x08);
    LCD_WR_DATA8(0x0A);
    LCD_WR_DATA8(0x13);
    LCD_WR_DATA8(0x26);
    LCD_WR_DATA8(0x36);
    LCD_WR_DATA8(0x00);
    LCD_WR_DATA8(0x0D);
    LCD_WR_DATA8(0x0E);
    LCD_WR_DATA8(0x10);

    LCD_WR_REG(0x3A);
    LCD_WR_DATA8(0x05);

    LCD_WR_REG(0x36);
    if (USE_HORIZONTAL == 0)LCD_WR_DATA8(0x08);
    else if (USE_HORIZONTAL == 1)LCD_WR_DATA8(0xC8);
    else if (USE_HORIZONTAL == 2)LCD_WR_DATA8(0x78);
    else LCD_WR_DATA8(0xA8);

    LCD_WR_REG(0x29);
}


/******************************************************************************
函数说明：LCD清屏函数
入口数据：无
返回值：  无
******************************************************************************/
void LCD_Clear(u16 Color)
{
    u16 i, j;
    LCD_Address_Set(0, 0, LCD_W - 1, LCD_H - 1);
    for (i = 0; i<LCD_W; i++)
    {
        for (j = 0; j<LCD_H; j++)
        {
            LCD_WR_DATA(Color);
        }
    }
}


/******************************************************************************
函数说明：LCD显示汉字
入口数据：x,y   起始坐标
index 汉字的序号
size  字号
返回值：  无
******************************************************************************/
void LCD_ShowChinese(u16 x, u16 y, u8 index, u8 size, u16 color)
{
    u8 i, j;
    u8 *temp, size1;
    if (size == 16){ temp = Hzk16; }//选择字号
    if (size == 32){ temp = Hzk32; }
    LCD_Address_Set(x, y, x + size - 1, y + size - 1); //设置一个汉字的区域
    size1 = size*size / 8;//一个汉字所占的字节
    temp += index*size1;//写入的起始位置
    for (j = 0; j<size1; j++)
    {
        for (i = 0; i<8; i++)
        {
            if ((*temp&(1 << i)) != 0)//从数据的低位开始读
            {
                LCD_WR_DATA(color);//点亮
            }
            else
            {
                LCD_WR_DATA(BACK_COLOR);//不点亮
            }
        }
        temp++;
    }
}


/******************************************************************************
函数说明：画点
入口数据：x,y   起始坐标
返回值：  无
******************************************************************************/
void LCD_DrawPoint(u16 x, u16 y, u16 color)
{
    LCD_Address_Set(x, y, x, y);//设置光标位置
    LCD_WR_DATA(color);
}


/******************************************************************************
函数说明：LCD画一个大的点
入口数据：x,y   起始坐标
返回值：  无
******************************************************************************/
void LCD_DrawPoint_big(u16 x, u16 y, u16 color)
{
    LCD_Fill(x - 1, y - 1, x + 1, y + 1, color);
}


/******************************************************************************
函数说明：在指定区域填充颜色
入口数据：xsta,ysta   起始坐标
xend,yend   终止坐标
返回值：  无
******************************************************************************/
void LCD_Fill(u16 xsta, u16 ysta, u16 xend, u16 yend, u16 color)
{
    u16 i, j;
    LCD_Address_Set(xsta, ysta, xend, yend);      //设置光标位置
    for (i = ysta; i <= yend; i++)
    {
        for (j = xsta; j <= xend; j++)LCD_WR_DATA(color);//设置光标位置
    }
}


/******************************************************************************
函数说明：画线
入口数据：x1,y1   起始坐标
x2,y2   终止坐标
返回值：  无
******************************************************************************/
void LCD_DrawLine(u16 x1, u16 y1, u16 x2, u16 y2, u16 color)
{
    u16 t;
    int xerr = 0, yerr = 0, delta_x, delta_y, distance;
    int incx, incy, uRow, uCol;
    delta_x = x2 - x1; //计算坐标增量
    delta_y = y2 - y1;
    uRow = x1;//画线起点坐标
    uCol = y1;
    if (delta_x>0)incx = 1; //设置单步方向
    else if (delta_x == 0)incx = 0;//垂直线
    else { incx = -1; delta_x = -delta_x; }
    if (delta_y>0)incy = 1;
    else if (delta_y == 0)incy = 0;//水平线
    else { incy = -1; delta_y = -delta_x; }
    if (delta_x>delta_y)distance = delta_x; //选取基本增量坐标轴
    else distance = delta_y;
    for (t = 0; t<distance + 1; t++)
    {
        LCD_DrawPoint(uRow, uCol, color);//画点
        xerr += delta_x;
        yerr += delta_y;
        if (xerr>distance)
        {
            xerr -= distance;
            uRow += incx;
        }
        if (yerr>distance)
        {
            yerr -= distance;
            uCol += incy;
        }
    }
}


/******************************************************************************
函数说明：画矩形
入口数据：x1,y1   起始坐标
x2,y2   终止坐标
返回值：  无
******************************************************************************/
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2, u16 color)
{
    LCD_DrawLine(x1, y1, x2, y1, color);
    LCD_DrawLine(x1, y1, x1, y2, color);
    LCD_DrawLine(x1, y2, x2, y2, color);
    LCD_DrawLine(x2, y1, x2, y2, color);
}


/******************************************************************************
函数说明：画圆
入口数据：x0,y0   圆心坐标
r       半径
返回值：  无
******************************************************************************/
void Draw_Circle(u16 x0, u16 y0, u8 r, u16 color)
{
    int a, b;
    a = 0; b = r;
    while (a <= b)
    {
        LCD_DrawPoint(x0 - b, y0 - a, color);             //3
        LCD_DrawPoint(x0 + b, y0 - a, color);             //0
        LCD_DrawPoint(x0 - a, y0 + b, color);             //1
        LCD_DrawPoint(x0 - a, y0 - b, color);             //2
        LCD_DrawPoint(x0 + b, y0 + a, color);             //4
        LCD_DrawPoint(x0 + a, y0 - b, color);             //5
        LCD_DrawPoint(x0 + a, y0 + b, color);             //6
        LCD_DrawPoint(x0 - b, y0 + a, color);             //7
        a++;
        if ((a*a + b*b)>(r*r))//判断要画的点是否过远
        {
            b--;
        }
    }
}


/******************************************************************************
函数说明：显示字符
入口数据：x,y    起点坐标
num    要显示的字符
mode   1叠加方式  0非叠加方式
返回值：  无
******************************************************************************/
void LCD_ShowChar(u16 x, u16 y, u8 num, u8 mode, u16 color)
{
    u8 temp;
    u8 pos, t;
    u16 x0 = x;
    if (x>LCD_W - 16 || y>LCD_H - 16)return;        //设置窗口
    num = num - ' ';//得到偏移后的值
    LCD_Address_Set(x, y, x + 8 - 1, y + 16 - 1);      //设置光标位置
    if (!mode) //非叠加方式
    {
        for (pos = 0; pos<16; pos++)
        {
            temp = asc2_1608[(u16)num * 16 + pos];       //调用1608字体
            for (t = 0; t<8; t++)
            {
                if (temp & 0x01)LCD_WR_DATA(color);
                else LCD_WR_DATA(BACK_COLOR);
                temp >>= 1;
                x++;
            }
            x = x0;
            y++;
        }
    }
    else//叠加方式
    {
        for (pos = 0; pos<16; pos++)
        {
            temp = asc2_1608[(u16)num * 16 + pos];       //调用1608字体
            for (t = 0; t<8; t++)
            {
                if (temp & 0x01)LCD_DrawPoint(x + t, y + pos, color);//画一个点
                temp >>= 1;
            }
        }
    }
}


/******************************************************************************
函数说明：显示字符串
入口数据：x,y    起点坐标
*p     字符串起始地址
返回值：  无
******************************************************************************/
void LCD_ShowString(u16 x, u16 y, const u8 *p, u16 color)
{
    while (*p != '\0')
    {
        if (x>LCD_W - 16){ x = 0; y += 16; }
        if (y>LCD_H - 16){ y = x = 0; LCD_Clear(RED); }
        LCD_ShowChar(x, y, *p, 0, color);
        x += 8;
        p++;
    }
}


/******************************************************************************
函数说明：指数函数
入口数据：m底数，n指数
返回值：  无
******************************************************************************/
u32 mypow(u8 m, u8 n)
{
    u32 result = 1;
    while (n--)result *= m;
    return result;
}


/******************************************************************************
函数说明：显示数字
入口数据：x,y    起点坐标
num    要显示的数字
len    要显示的数字个数
返回值：  无
******************************************************************************/
void LCD_ShowNum(u16 x, u16 y, u16 num, u8 len, u16 color)
{
    u8 t, temp;
    u8 enshow = 0;
    for (t = 0; t<len; t++)
    {
        temp = (num / mypow(10, len - t - 1)) % 10;
        if (enshow == 0 && t<(len - 1))
        {
            if (temp == 0)
            {
                LCD_ShowChar(x + 8 * t, y, ' ', 0, color);
                continue;
            }
            else enshow = 1;

        }
        LCD_ShowChar(x + 8 * t, y, temp + 48, 0, color);
    }
}


/******************************************************************************
函数说明：显示小数
入口数据：x,y    起点坐标
num    要显示的小数
len    要显示的数字个数
返回值：  无
******************************************************************************/
void LCD_ShowNum1(u16 x, u16 y, float num, u8 len, u16 color)
{
    u8 t, temp;
    u16 num1;
    num1 = num * 100;
    for (t = 0; t<len; t++)
    {
        temp = (num1 / mypow(10, len - t - 1)) % 10;
        if (t == (len - 2))
        {
            LCD_ShowChar(x + 8 * (len - 2), y, '.', 0, color);
            t++;
            len += 1;
        }
        LCD_ShowChar(x + 8 * t, y, temp + 48, 0, color);
    }
 }

2.2 board_oled.h

#ifndef BOARD_OLED_H
#define BOARD_OLED_H

#ifdef __cplusplus
extern "C" {
#endif

//              GND   电源地
//              VCC   接5V或3.3v电源
//              SCL   接IOID_9
//              SDA   接IOID_10
//              RES   接IOID_4
//              DC    接IOID_26
//              CS    接IOID_5
//              BLK   背光悬空为高电平

#define USE_HORIZONTAL 2  //设置横屏或者竖屏显示 0或1为竖屏 2或3为横屏

#if USE_HORIZONTAL==0||USE_HORIZONTAL==1
#define LCD_W 80
#define LCD_H 160

#else
#define LCD_W 160
#define LCD_H 80
#endif

#define u8 unsigned char
#define u16 unsigned int
#define u32 unsigned long


#define OLED_CMD  0 //写命令
#define OLED_DATA 1 //写数据

extern  u16 BACK_COLOR;   //背景色

void delayMs(u8 ms);
void LCD_Writ_Bus(u8 dat);
void LCD_WR_DATA8(u8 dat);
void LCD_WR_DATA(u16 dat);
void LCD_WR_REG(u8 dat);
void LCD_Address_Set(u16 x1,u16 y1,u16 x2,u16 y2);
void Lcd_Init(void);
void LCD_demo();
void LCD_Clear(u16 Color);
void LCD_ShowChinese(u16 x,u16 y,u8 index,u8 size,u16 color);
void LCD_DrawPoint(u16 x,u16 y,u16 color);
void LCD_DrawPoint_big(u16 x,u16 y,u16 color);
void LCD_Fill(u16 xsta,u16 ysta,u16 xend,u16 yend,u16 color);
void LCD_DrawLine(u16 x1,u16 y1,u16 x2,u16 y2,u16 color);
void LCD_DrawRectangle(u16 x1, u16 y1, u16 x2, u16 y2,u16 color);
void Draw_Circle(u16 x0,u16 y0,u8 r,u16 color);
void LCD_ShowChar(u16 x,u16 y,u8 num,u8 mode,u16 color);
void LCD_ShowString(u16 x,u16 y,const u8 *p,u16 color);
u32 mypow(u8 m,u8 n);
void LCD_ShowNum(u16 x,u16 y,u16 num,u8 len,u16 color);
void LCD_ShowNum1(u16 x,u16 y,float num,u8 len,u16 color);

//画笔颜色
#define WHITE            0xFFFF
#define BLACK            0x0000
#define BLUE             0x001F
#define BRED             0XF81F
#define GRED                   0XFFE0
#define GBLUE                  0X07FF
#define RED              0xF800
#define MAGENTA          0xF81F
#define GREEN            0x07E0
#define CYAN             0x7FFF
#define YELLOW           0xFFE0
#define BROWN                0XBC40 //棕色
#define BRRED                0XFC07 //棕红色
#define GRAY                 0X8430 //灰色
//GUI颜色

#define DARKBLUE         0X01CF //深蓝色
#define LIGHTBLUE        0X7D7C //浅蓝色
#define GRAYBLUE         0X5458 //灰蓝色
//以上三色为PANEL的颜色

#define LIGHTGREEN       0X841F //浅绿色
#define LGRAY                0XC618 //浅灰色(PANNEL),窗体背景色

#define LGRAYBLUE        0XA651 //浅灰蓝色(中间层颜色)
#define LBBLUE           0X2B12 //浅棕蓝色(选择条目的反色)


#ifdef __cplusplus
}
#endif

#endif /* BOARD_OLED_H */

2.3 oledfont.h

#ifndef __OLEDFONT_H
#define __OLEDFONT_H 	   
//常用ASCII表
//偏移量32
//ASCII字符集
//偏移量32
//大小:12*6
#define	u8 unsigned char
#define	u16 unsigned int
#define	u32 unsigned long

/****************************************32*32的点阵************************************/
u8 Hzk32[]={			  

0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x80,0x01,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x10,0x80,0x01,0x0C,0xF0,0xFF,0xFF,0x0F,0x30,0x80,0x01,0x04,0x30,0x80,0x01,0x04,
0x30,0x80,0x01,0x04,0x30,0x80,0x01,0x04,0x30,0x80,0x01,0x04,0x30,0x80,0x01,0x04,
0x30,0x80,0x01,0x04,0x30,0x80,0x01,0x04,0xF0,0xFF,0xFF,0x07,0x30,0x80,0x01,0x04,
0x30,0x80,0x01,0x04,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,/*"中",0*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x80,0x01,
0x00,0xFF,0xFF,0x01,0x00,0x03,0x80,0x01,0x00,0x03,0x80,0x01,0x00,0xFF,0xFF,0x01,
0x00,0x03,0x80,0x01,0x00,0x03,0x80,0x01,0x00,0xFF,0xFF,0x01,0x00,0x81,0x81,0x00,
0x00,0x00,0x03,0x00,0x00,0x00,0x03,0x1C,0xFC,0xFF,0xFF,0x3F,0x00,0x00,0x40,0x00,
0x00,0x03,0xC0,0x01,0x00,0xFF,0xFF,0x01,0x00,0x03,0xC0,0x00,0x00,0x03,0xC0,0x00,
0x00,0x03,0xC0,0x00,0x00,0xFF,0xFF,0x00,0x00,0x01,0x41,0x00,0x00,0x04,0x01,0x00,
0x00,0x0E,0x71,0x00,0x00,0x07,0x81,0x01,0x80,0x01,0x01,0x07,0x60,0x00,0x01,0x0E,
0x18,0x98,0x01,0x1C,0x04,0xE0,0x01,0x18,0x00,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,/*"景",1*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0xF0,0xFF,0xFF,0x1F,
0x30,0x00,0x00,0x0C,0x30,0x00,0x00,0x0C,0x30,0x00,0x10,0x0C,0x30,0xFE,0x3F,0x0C,
0x30,0x04,0x00,0x0C,0x30,0x00,0x00,0x0C,0x30,0x00,0x00,0x0C,0x30,0x00,0x00,0x0C,
0x30,0x00,0xC0,0x0C,0xF0,0xFF,0xFF,0x0D,0x30,0x30,0x06,0x0E,0x30,0x30,0x06,0x0C,
0x30,0x10,0x06,0x0C,0x30,0x10,0x06,0x0C,0x30,0x10,0x06,0x0C,0x30,0x18,0x86,0x0C,
0x30,0x18,0x86,0x0C,0x30,0x08,0x06,0x0D,0x30,0x0C,0x86,0x0D,0x30,0x06,0xEE,0x0F,
0x30,0x02,0xFC,0x0D,0x30,0x01,0x00,0x0C,0xF0,0x00,0x00,0x0C,0x30,0x00,0x00,0x0C,
0xF0,0xFF,0xFF,0x0F,0x30,0x00,0x00,0x0C,0x10,0x00,0x00,0x04,0x00,0x00,0x00,0x00,/*"园",2*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0xC0,0x01,0x00,
0x00,0xC0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0xC0,0x00,0x00,0x00,0xC0,0x00,0x00,
0xE0,0xFF,0xFF,0x03,0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,
0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,0xE0,0xFF,0xFF,0x03,
0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,0x60,0xC0,0x00,0x03,
0x60,0xC0,0x00,0x03,0xE0,0xFF,0xFF,0x03,0x60,0xC0,0x00,0x01,0x60,0xC0,0x00,0x00,
0x00,0xC0,0x00,0x08,0x00,0xC0,0x00,0x10,0x00,0xC0,0x00,0x10,0x00,0xC0,0x00,0x18,
0x00,0xC0,0x01,0x38,0x00,0x80,0xFF,0x1F,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*"电",3*/
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x03,
0xC0,0xFF,0xFF,0x07,0x00,0x00,0x80,0x07,0x00,0x00,0xC0,0x00,0x00,0x00,0x60,0x00,
0x00,0x00,0x18,0x00,0x00,0x00,0x0C,0x00,0x00,0x80,0x03,0x00,0x00,0x80,0x03,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x08,0x00,0x80,0x01,0x1C,0xFC,0xFF,0xFF,0x3F,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,0x00,0x80,0x01,0x00,
0x00,0xFC,0x01,0x00,0x00,0xE0,0x00,0x00,0x00,0x40,0x00,0x00,0x00,0x00,0x00,0x00,/*"子",4*/};

const u8 asc2_1608[1520]={
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,0x18,0x18,0x00,0x00,
0x00,0x48,0x6C,0x24,0x12,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x24,0x24,0x24,0x7F,0x12,0x12,0x12,0x7F,0x12,0x12,0x12,0x00,0x00,
0x00,0x00,0x08,0x1C,0x2A,0x2A,0x0A,0x0C,0x18,0x28,0x28,0x2A,0x2A,0x1C,0x08,0x08,
0x00,0x00,0x00,0x22,0x25,0x15,0x15,0x15,0x2A,0x58,0x54,0x54,0x54,0x22,0x00,0x00,
0x00,0x00,0x00,0x0C,0x12,0x12,0x12,0x0A,0x76,0x25,0x29,0x11,0x91,0x6E,0x00,0x00,
0x00,0x06,0x06,0x04,0x03,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x40,0x20,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x10,0x10,0x20,0x40,0x00,
0x00,0x02,0x04,0x08,0x08,0x10,0x10,0x10,0x10,0x10,0x10,0x08,0x08,0x04,0x02,0x00,
0x00,0x00,0x00,0x00,0x08,0x08,0x6B,0x1C,0x1C,0x6B,0x08,0x08,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x08,0x08,0x08,0x08,0x7F,0x08,0x08,0x08,0x08,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x04,0x03,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFE,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x00,0x00,
0x00,0x00,0x80,0x40,0x40,0x20,0x20,0x10,0x10,0x08,0x08,0x04,0x04,0x02,0x02,0x00,
0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x24,0x18,0x00,0x00,
0x00,0x00,0x00,0x08,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00,
0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x20,0x20,0x10,0x08,0x04,0x42,0x7E,0x00,0x00,
0x00,0x00,0x00,0x3C,0x42,0x42,0x20,0x18,0x20,0x40,0x40,0x42,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0x20,0x30,0x28,0x24,0x24,0x22,0x22,0x7E,0x20,0x20,0x78,0x00,0x00,
0x00,0x00,0x00,0x7E,0x02,0x02,0x02,0x1A,0x26,0x40,0x40,0x42,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0x38,0x24,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x24,0x18,0x00,0x00,
0x00,0x00,0x00,0x7E,0x22,0x22,0x10,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x00,0x00,
0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x24,0x18,0x24,0x42,0x42,0x42,0x3C,0x00,0x00,
0x00,0x00,0x00,0x18,0x24,0x42,0x42,0x42,0x64,0x58,0x40,0x40,0x24,0x1C,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,0x00,0x00,0x18,0x18,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x08,0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x04,
0x00,0x00,0x00,0x40,0x20,0x10,0x08,0x04,0x02,0x04,0x08,0x10,0x20,0x40,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x7F,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x02,0x04,0x08,0x10,0x20,0x40,0x20,0x10,0x08,0x04,0x02,0x00,0x00,
0x00,0x00,0x00,0x3C,0x42,0x42,0x46,0x40,0x20,0x10,0x10,0x00,0x18,0x18,0x00,0x00,
0x00,0x00,0x00,0x1C,0x22,0x5A,0x55,0x55,0x55,0x55,0x2D,0x42,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0x08,0x08,0x18,0x14,0x14,0x24,0x3C,0x22,0x42,0x42,0xE7,0x00,0x00,
0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x1E,0x22,0x42,0x42,0x42,0x22,0x1F,0x00,0x00,
0x00,0x00,0x00,0x7C,0x42,0x42,0x01,0x01,0x01,0x01,0x01,0x42,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0x1F,0x22,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x22,0x1F,0x00,0x00,
0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x42,0x42,0x3F,0x00,0x00,
0x00,0x00,0x00,0x3F,0x42,0x12,0x12,0x1E,0x12,0x12,0x02,0x02,0x02,0x07,0x00,0x00,
0x00,0x00,0x00,0x3C,0x22,0x22,0x01,0x01,0x01,0x71,0x21,0x22,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x7E,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,
0x00,0x00,0x00,0x3E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00,
0x00,0x00,0x00,0x7C,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x11,0x0F,
0x00,0x00,0x00,0x77,0x22,0x12,0x0A,0x0E,0x0A,0x12,0x12,0x22,0x22,0x77,0x00,0x00,
0x00,0x00,0x00,0x07,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x02,0x42,0x7F,0x00,0x00,
0x00,0x00,0x00,0x77,0x36,0x36,0x36,0x36,0x2A,0x2A,0x2A,0x2A,0x2A,0x6B,0x00,0x00,
0x00,0x00,0x00,0xE3,0x46,0x46,0x4A,0x4A,0x52,0x52,0x52,0x62,0x62,0x47,0x00,0x00,
0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x41,0x41,0x22,0x1C,0x00,0x00,
0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x42,0x3E,0x02,0x02,0x02,0x02,0x07,0x00,0x00,
0x00,0x00,0x00,0x1C,0x22,0x41,0x41,0x41,0x41,0x41,0x4D,0x53,0x32,0x1C,0x60,0x00,
0x00,0x00,0x00,0x3F,0x42,0x42,0x42,0x3E,0x12,0x12,0x22,0x22,0x42,0xC7,0x00,0x00,
0x00,0x00,0x00,0x7C,0x42,0x42,0x02,0x04,0x18,0x20,0x40,0x42,0x42,0x3E,0x00,0x00,
0x00,0x00,0x00,0x7F,0x49,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00,
0x00,0x00,0x00,0xE7,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00,
0x00,0x00,0x00,0xE7,0x42,0x42,0x22,0x24,0x24,0x14,0x14,0x18,0x08,0x08,0x00,0x00,
0x00,0x00,0x00,0x6B,0x49,0x49,0x49,0x49,0x55,0x55,0x36,0x22,0x22,0x22,0x00,0x00,
0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x18,0x18,0x18,0x24,0x24,0x42,0xE7,0x00,0x00,
0x00,0x00,0x00,0x77,0x22,0x22,0x14,0x14,0x08,0x08,0x08,0x08,0x08,0x1C,0x00,0x00,
0x00,0x00,0x00,0x7E,0x21,0x20,0x10,0x10,0x08,0x04,0x04,0x42,0x42,0x3F,0x00,0x00,
0x00,0x78,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x78,0x00,
0x00,0x00,0x02,0x02,0x04,0x04,0x08,0x08,0x08,0x10,0x10,0x20,0x20,0x20,0x40,0x40,
0x00,0x1E,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x1E,0x00,
0x00,0x38,0x44,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,
0x00,0x06,0x08,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x78,0x44,0x42,0x42,0xFC,0x00,0x00,
0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x1A,0x26,0x42,0x42,0x42,0x26,0x1A,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x38,0x44,0x02,0x02,0x02,0x44,0x38,0x00,0x00,
0x00,0x00,0x00,0x60,0x40,0x40,0x40,0x78,0x44,0x42,0x42,0x42,0x64,0xD8,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x7E,0x02,0x02,0x42,0x3C,0x00,0x00,
0x00,0x00,0x00,0xF0,0x88,0x08,0x08,0x7E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x22,0x22,0x1C,0x02,0x3C,0x42,0x42,0x3C,
0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x3A,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,
0x00,0x00,0x00,0x0C,0x0C,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00,
0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x38,0x20,0x20,0x20,0x20,0x20,0x20,0x22,0x1E,
0x00,0x00,0x00,0x03,0x02,0x02,0x02,0x72,0x12,0x0A,0x16,0x12,0x22,0x77,0x00,0x00,
0x00,0x00,0x00,0x0E,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x3E,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7F,0x92,0x92,0x92,0x92,0x92,0xB7,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3B,0x46,0x42,0x42,0x42,0x42,0xE7,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x3C,0x42,0x42,0x42,0x42,0x42,0x3C,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x1B,0x26,0x42,0x42,0x42,0x22,0x1E,0x02,0x07,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x78,0x44,0x42,0x42,0x42,0x44,0x78,0x40,0xE0,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x77,0x4C,0x04,0x04,0x04,0x04,0x1F,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x42,0x02,0x3C,0x40,0x42,0x3E,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x08,0x08,0x3E,0x08,0x08,0x08,0x08,0x08,0x30,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x63,0x42,0x42,0x42,0x42,0x62,0xDC,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x08,0x08,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xEB,0x49,0x49,0x55,0x55,0x22,0x22,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x76,0x24,0x18,0x18,0x18,0x24,0x6E,0x00,0x00,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xE7,0x42,0x24,0x24,0x14,0x18,0x08,0x08,0x07,
0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7E,0x22,0x10,0x08,0x08,0x44,0x7E,0x00,0x00,
0x00,0xC0,0x20,0x20,0x20,0x20,0x20,0x10,0x20,0x20,0x20,0x20,0x20,0x20,0xC0,0x00,
0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,0x10,
0x00,0x06,0x08,0x08,0x08,0x08,0x08,0x10,0x08,0x08,0x08,0x08,0x08,0x08,0x06,0x00,
0x0C,0x32,0xC2,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
}; 




u8 Hzk16[]={

0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0xFC,0x1F,0x84,0x10,0x84,0x10,0x84,0x10,
0x84,0x10,0x84,0x10,0xFC,0x1F,0x84,0x10,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,/*"中",0*/

0xF8,0x0F,0x08,0x08,0xF8,0x0F,0x08,0x08,0xF8,0x0F,0x80,0x00,0xFF,0x7F,0x00,0x00,
0xF8,0x0F,0x08,0x08,0x08,0x08,0xF8,0x0F,0x80,0x00,0x84,0x10,0xA2,0x20,0x40,0x00,/*"景",1*/

0x00,0x00,0xFE,0x3F,0x02,0x20,0xF2,0x27,0x02,0x20,0x02,0x20,0xFA,0x2F,0x22,0x21,
0x22,0x21,0x22,0x21,0x12,0x29,0x12,0x29,0x0A,0x2E,0x02,0x20,0xFE,0x3F,0x02,0x20,/*"园",2*/

0x80,0x00,0x80,0x00,0x80,0x00,0xFC,0x1F,0x84,0x10,0x84,0x10,0x84,0x10,0xFC,0x1F,
0x84,0x10,0x84,0x10,0x84,0x10,0xFC,0x1F,0x84,0x50,0x80,0x40,0x80,0x40,0x00,0x7F,/*"电",3*/

0x00,0x00,0xFE,0x1F,0x00,0x08,0x00,0x04,0x00,0x02,0x80,0x01,0x80,0x00,0xFF,0x7F,
0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0x80,0x00,0xA0,0x00,0x40,0x00,/*"子",4*/

0x10,0x08,0xB8,0x08,0x0F,0x09,0x08,0x09,0x08,0x08,0xBF,0x08,0x08,0x09,0x1C,0x09,
0x2C,0x08,0x0A,0x78,0xCA,0x0F,0x09,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,0x08,/*"科",5*/

0x08,0x04,0x08,0x04,0x08,0x04,0xC8,0x7F,0x3F,0x04,0x08,0x04,0x08,0x04,0xA8,0x3F,
0x18,0x21,0x0C,0x11,0x0B,0x12,0x08,0x0A,0x08,0x04,0x08,0x0A,0x8A,0x11,0x64,0x60,/*"技",6*/


};

#endif

三、使用例子

1）添加头文件（例 simple_peripheral.c 中）

#include "board_oled.h"

2）添加OLED屏显示测试代码（simple_peripheral.c 的 static void SimplePeripheral_init(void)函数末尾中）

LCD_demo();// OLED屏显示测试代码

由 LiangJian 写于 2019 年 9 月 30 日

• 参考： CC2640R2F学习笔记（2）——OLED屏使用
 【CC2640R2F】香瓜CC2640R2F之LCD

liangjianneu

关注

1
点赞
踩
3

收藏

觉得还不错? 一键收藏
0
评论
CC2640R2F程序移植——0.96OLED_IPS屏(ss7725驱动)

@CC2640R2F学习笔记——0.96OLED_IPS屏(ss7725驱动))一、引脚说明1.1 接口定义引脚功能说明GND电源地VCC电源正 3.3~5VD0SPI接口时为SPI时钟线，IIC接口时为IIC时钟线D1SPI接口时为SPI数据线，IIC接口时为IIC数据线RSTOLED复位，OLED在上电后需做一次复位DCSPI...
复制链接

扫一扫