首先将 ssd1306.py 文件拖到openmv中。
ssd1306.py:
#MicroPython SSD1306 OLED driver, I2C and SPI interfaces created by Adafruit
import time
import framebuf
# register definitions
SET_CONTRAST = const(0x81)
SET_ENTIRE_ON = const(0xa4)
SET_NORM_INV = const(0xa6)
SET_DISP = const(0xae)
SET_MEM_ADDR = const(0x20)
SET_COL_ADDR = const(0x21)
SET_PAGE_ADDR = const(0x22)
SET_DISP_START_LINE = const(0x40)
SET_SEG_REMAP = const(0xa0)
SET_MUX_RATIO = const(0xa8)
SET_COM_OUT_DIR = const(0xc0)
SET_DISP_OFFSET = const(0xd3)
SET_COM_PIN_CFG = const(0xda)
SET_DISP_CLK_DIV = const(0xd5)
SET_PRECHARGE = const(0xd9)
SET_VCOM_DESEL = const(0xdb)
SET_CHARGE_PUMP = const(0x8d)
class SSD1306:
def __init__(self, width, height, external_vcc):
self.width = width
self.height = height
self.external_vcc = external_vcc
self.pages = self.height // 8
# Note the subclass must initialize self.framebuf to a framebuffer.
# This is necessary because the underlying data buffer is different
# between I2C and SPI implementations (I2C needs an extra byte).
self.poweron()
self.init_display()
def init_display(self):
for cmd in (
SET_DISP | 0x00, # off
# address setting
SET_MEM_ADDR, 0x00, # horizontal
# resolution and layout
SET_DISP_START_LINE | 0x00,
SET_SEG_REMAP | 0x01, # column addr 127 mapped to SEG0
SET_MUX_RATIO, self.height - 1,
SET_COM_OUT_DIR | 0x08, # scan from COM[N] to COM0
SET_DISP_OFFSET, 0x00,
SET_COM_PIN_CFG, 0x02 if self.height == 32 else 0x12,
# timing and driving scheme
SET_DISP_CLK_DIV, 0x80,
SET_PRECHARGE, 0x22 if self.external_vcc else 0xf1,
SET_VCOM_DESEL, 0x30, # 0.83*Vcc
# display
SET_CONTRAST, 0xff, # maximum
SET_ENTIRE_ON, # output follows RAM contents
SET_NORM_INV, # not inverted
# charge pump
SET_CHARGE_PUMP, 0x10 if self.external_vcc else 0x14,
SET_DISP | 0x01): # on
self.write_cmd(cmd)
self.fill(0)
self.show()
def poweroff(self):
self.write_cmd(SET_DISP | 0x00)
def contrast(self, contrast):
self.write_cmd(SET_CONTRAST)
self.write_cmd(contrast)
def invert(self, invert):
self.write_cmd(SET_NORM_INV | (invert & 1))
def show(self):
x0 = 0
x1 = self.width - 1
if self.width == 64:
# displays with width of 64 pixels are shifted by 32
x0 += 32
x1 += 32
self.write_cmd(SET_COL_ADDR)
self.write_cmd(x0)
self.write_cmd(x1)
self.write_cmd(SET_PAGE_ADDR)
self.write_cmd(0)
self.write_cmd(self.pages - 1)
self.write_framebuf()
def fill(self, col):
self.framebuf.fill(col)
def pixel(self, x, y, col):
self.framebuf.pixel(x, y, col)
def scroll(self, dx, dy):
self.framebuf.scroll(dx, dy)
def text(self, string, x, y, col=1):
self.framebuf.text(string, x, y, col)
class SSD1306_I2C(SSD1306):
def __init__(self, width, height, i2c, addr=0x3c, external_vcc=False):
self.i2c = i2c
self.addr = addr
self.temp = bytearray(2)
# Add an extra byte to the data buffer to hold an I2C data/command byte
# to use hardware-compatible I2C transactions. A memoryview of the
# buffer is used to mask this byte from the framebuffer operations
# (without a major memory hit as memoryview doesn't copy to a separate
# buffer).
self.buffer = bytearray(((height // 8) * width) + 1)
self.buffer[0] = 0x40 # Set first byte of data buffer to Co=0, D/C=1
self.framebuf = framebuf.FrameBuffer1(memoryview(self.buffer)[1:], width, height)
super().__init__(width, height, external_vcc)
def write_cmd(self, cmd):
self.temp[0] = 0x80 # Co=1, D/C#=0
self.temp[1] = cmd
self.i2c.writeto(self.addr, self.temp)
def write_framebuf(self):
# Blast out the frame buffer using a single I2C transaction to support
# hardware I2C interfaces.
self.i2c.writeto(self.addr, self.buffer)
def poweron(self):
pass
class SSD1306_SPI(SSD1306):
def __init__(self, width, height, spi, dc, res, cs, external_vcc=False):
self.rate = 10 * 1024 * 1024
dc.init(dc.OUT, value=0)
res.init(res.OUT, value=0)
cs.init(cs.OUT, value=1)
self.spi = spi
self.dc = dc
self.res = res
self.cs = cs
self.buffer = bytearray((height // 8) * width)
self.framebuf = framebuf.FrameBuffer1(self.buffer, width, height)
super().__init__(width, height, external_vcc)
def write_cmd(self, cmd):
self.spi.init(baudrate=self.rate, polarity=0, phase=0)
self.cs.high()
self.dc.low()
self.cs.low()
self.spi.write(bytearray([cmd]))
self.cs.high()
def write_framebuf(self):
self.spi.init(baudrate=self.rate, polarity=0, phase=0)
self.cs.high()
self.dc.high()
self.cs.low()
self.spi.write(self.buffer)
self.cs.high()
def poweron(self):
self.res.high()
time.sleep_ms(1)
self.res.low()
time.sleep_ms(10)
self.res.high()
openmv中的代码:
from machine import I2C,Pin #从 machine 模块导入 I2C、 Pin 子模块
from ssd1306 import SSD1306_I2C #从 ssd1306 模块中导入 SSD1306_I2C 子模块
import time
# 初始化 sda--p1 scl--p0
i2c = I2C(sda=Pin("P1"), scl=Pin("P0"),freq=80000 )
#OLED 显示屏初始化: 128*64 分辨率,OLED 的 I2C 地址是 0x3c
oled = SSD1306_I2C(128, 64, i2c, addr=0x3c)
#中文显示
def chinese(ch_str, x_axis, y_axis):
offset_ = 0
for k in ch_str:
code = 0x00 # 将中文转成16进制编码
data_code = k.encode("utf-8")
code |= data_code[0] << 16
code |= data_code[1] << 8
code |= data_code[2]
byte_data = fonts[code]
for y in range(0, 16):
a_ = bin(byte_data[y]).replace('0b', '')
while len(a_) < 8:
a_ = '0'+ a_
b_ = bin(byte_data[y+16]).replace('0b', '')
while len(b_) < 8:
b_ = '0'+ b_
for x in range(0, 8):
oled.pixel(x_axis + offset_ + x, y+y_axis, int(a_[x]))
oled.pixel(x_axis + offset_ + x +8, y+y_axis, int(b_[x]))
offset_ += 16
fonts = {
0xe4b8ad:
[0x01,0x01,0x01,0x01,0x3F,0x21,0x21,0x21,0x21,0x21,0x3F,0x21,0x01,0x01,0x01,0x01,
0x00,0x00,0x00,0x00,0xF8,0x08,0x08,0x08,0x08,0x08,0xF8,0x08,0x00,0x00,0x00,0x00], # 中
0xe69687:
[0x02,0x01,0x01,0xFF,0x10,0x10,0x08,0x08,0x04,0x02,0x01,0x02,0x04,0x08,0x30,0xC0,
0x00,0x00,0x00,0xFE,0x10,0x10,0x20,0x20,0x40,0x80,0x00,0x80,0x40,0x20,0x18,0x06, # 文
}
while(True):
oled.fill(0)#清屏
chinese('中文',16,4)#显示中文
oled.show()#OLED显示生效
time.sleep(1)#延时1S
oled.fill(0)#清屏
oled.text('ROBOT',50,25)#从50行25列开始显示ROBOT
oled.show()#OLED显示生效
time.sleep(1)#延时1S
中文具体显示方法:
1.查找对应UFT-8编码值;
2.通过软件制作显示的样子。
一.UFT-8编码值
查看字符编码(UTF-8)http://www.mytju.com/classcode/tools/encode_utf8.asp
二.字符设计
下载 地址:https://doc.itprojects.cn/0006.zhishi.esp32/01.download/128x64ziku.rar
解压-点击 .exe
字符模式
也可以自行设计图案:图形模式--新建---选择尺寸---构建图像---生成字模。