2）在Makefile中加入
bks2410_config : unconfig
 @./mkconfig $(@:_config=) arm arm920t bks2410 NULL s3c24x0
我把我的板子起名叫bks2410，可以依自己的喜好修改
3）建立board/bks2410目录，拷贝board/smdk2410下的文件到board/bks2410目录，将smdk2410.c更名为bks2410.c
4）cp include/configs/smdk2410.h include/configs/bks2410.h
5）将arm-linux-gcc的目录加入到PATH环境变量中，我的是目录/opt/eldk/usr/bin:/opt/eldk/bin
6）测试编译能否成功：
make bks2410_config
make all ARCH=arm
生成u-boot.bin就OK了
7）依照你自己开发板的内存地址分配情况修改board/bks2410/memsetup.S文件，我的程序：
#include <config.h>
#include <version.h>
#define BWSCON 0x48000000
/* BWSCON */
#define DW8    (0x0)
#define DW16    (0x1)
#define DW32    (0x2)
#define WAIT    (0x1<<2)
#define UBLB    (0x1<<3)
#define B1_BWSCON    (DW32)
#define B2_BWSCON    (DW16)
#define B3_BWSCON    (DW16 + WAIT + UBLB)
#define B4_BWSCON    (DW16)
#define B5_BWSCON    (DW16)
#define B6_BWSCON    (DW32)
#define B7_BWSCON    (DW32)
/* BANK0CON */
#if 0
#define B0_Tacs    0x0 /*  0clk */
#define B0_Tcos    0x0 /*  0clk */
#define B0_Tacc    0x7 /* 14clk */
#define B0_Tcoh    0x0 /*  0clk */
#define B0_Tah    0x0 /*  0clk */
#define B0_Tacp    0x0
#define B0_PMC    0x0 /* normal */
#endif
#define B0_Tacs    0x3 /*  0clk */
#define B0_Tcos    0x3 /*  0clk */
#define B0_Tacc    0x7 /* 14clk */
#define B0_Tcoh    0x3 /*  0clk */
#define B0_Tah    0x3 /*  0clk */
#define B0_Tacp    0x1
#define B0_PMC    0x0 /* normal */
/* BANK1CON */
#if 0
#define B1_Tacs    0x0 /*  0clk */
#define B1_Tcos    0x0 /*  0clk */
#define B1_Tacc    0x7 /* 14clk */
#define B1_Tcoh    0x0 /*  0clk */
#define B1_Tah    0x0 /*  0clk */
#define B1_Tacp    0x0
#define B1_PMC    0x0
#endif
#define B1_Tacs    0x3 /*  0clk */
#define B1_Tcos    0x3 /*  0clk */
#define B1_Tacc    0x7 /* 14clk */
#define B1_Tcoh    0x3 /*  0clk */
#define B1_Tah    0x3 /*  0clk */
#define B1_Tacp    0x3
#define B1_PMC    0x0
#define B2_Tacs    0x0
#define B2_Tcos    0x0
#define B2_Tacc    0x7
#define B2_Tcoh    0x0
#define B2_Tah    0x0
#define B2_Tacp    0x0
#define B2_PMC    0x0
#if 0
#define B3_Tacs    0x0 /*  0clk */
#define B3_Tcos    0x3 /*  4clk */
#define B3_Tacc    0x7 /* 14clk */
#define B3_Tcoh    0x1 /*  1clk */
#define B3_Tah    0x0 /*  0clk */
#define B3_Tacp    0x3     /*  6clk */
#define B3_PMC    0x0 /* normal */
#endif
#define B3_Tacs    0x0 /*  0clk */
#define B3_Tcos    0x0 /*  4clk */
#define B3_Tacc    0x7 /* 14clk */
#define B3_Tcoh    0x0 /*  1clk */
#define B3_Tah    0x0 /*  0clk */
#define B3_Tacp    0x0     /*  6clk */
#define B3_PMC    0x0 /* normal */
#define B4_Tacs    0x0 /*  0clk */
#define B4_Tcos    0x0 /*  0clk */
#define B4_Tacc    0x7 /* 14clk */
#define B4_Tcoh    0x0 /*  0clk */
#define B4_Tah    0x0 /*  0clk */
#define B4_Tacp    0x0
#define B4_PMC    0x0 /* normal */
#define B5_Tacs    0x0 /*  0clk */
#define B5_Tcos    0x0 /*  0clk */
#define B5_Tacc    0x7 /* 14clk */
#define B5_Tcoh    0x0 /*  0clk */
#define B5_Tah    0x0 /*  0clk */
#define B5_Tacp    0x0
#define B5_PMC    0x0 /* normal */
#define B6_MT    0x3 /* SDRAM */
#define B6_Trcd     0x1
#define B6_SCAN    0x1 /* 9bit */
#define B7_MT    0x3 /* SDRAM */
#define B7_Trcd    0x1 /* 3clk */
#define B7_SCAN    0x1 /* 9bit */
/* REFRESH parameter */
#define REFEN    0x1 /* Refresh enable */
#define TREFMD    0x0 /* CBR(CAS before RAS)/Auto refresh */
#define Trp    0x0 /* 2clk */
#define Trc    0x3 /* 7clk */
#define Tchr    0x2 /* 3clk */
#define REFCNT    1113 /* period=15.6us, HCLK=60Mhz, (2048+1-15.6*60) */
/**************************************/
_TEXT_BASE:
 .word TEXT_BASE
.globl memsetup
memsetup:
 /* memory control configuration */
 /* make r0 relative the current location so that it */
 /* reads SMRDATA out of FLASH rather than memory ! */
 adr     r0, SMRDATA
 /*ldr r1, _TEXT_BASE*/
 /*sub r0, r0, r1*/
 ldr r1, =BWSCON /* Bus Width Status Controller */
 add     r2, r0, #13*4
0:
 ldr     r3, [r0], #4
 str     r3, [r1], #4
 cmp     r2, r0
 bne     0b
 /* everything is fine now */
 mov pc, lr
 .ltorg
/* the literal pools origin */
SMRDATA:
    .word (0+(B1_BWSCON<<4)+(B2_BWSCON<<8)+(B3_BWSCON<<12)+(B4_BWSCON<<16)+(B5_BWSCON<<20)+(B6_BWSCON<<24)+(B7_BWSCON<<28))
    .word ((B0_Tacs<<13)+(B0_Tcos<<11)+(B0_Tacc<<8)+(B0_Tcoh<<6)+(B0_Tah<<4)+(B0_Tacp<<2)+(B0_PMC))
    .word ((B1_Tacs<<13)+(B1_Tcos<<11)+(B1_Tacc<<8)+(B1_Tcoh<<6)+(B1_Tah<<4)+(B1_Tacp<<2)+(B1_PMC))
    .word ((B2_Tacs<<13)+(B2_Tcos<<11)+(B2_Tacc<<8)+(B2_Tcoh<<6)+(B2_Tah<<4)+(B2_Tacp<<2)+(B2_PMC))
    .word 0x1f7c/*((B3_Tacs<<13)+(B3_Tcos<<11)+(B3_Tacc<<8)+(B3_Tcoh<<6)+(B3_Tah<<4)+(B3_Tacp<<2)+(B3_PMC))*/
    .word ((B4_Tacs<<13)+(B4_Tcos<<11)+(B4_Tacc<<8)+(B4_Tcoh<<6)+(B4_Tah<<4)+(B4_Tacp<<2)+(B4_PMC))
    .word ((B5_Tacs<<13)+(B5_Tcos<<11)+(B5_Tacc<<8)+(B5_Tcoh<<6)+(B5_Tah<<4)+(B5_Tacp<<2)+(B5_PMC))
    .word ((B6_MT<<15)+(B6_Trcd<<2)+(B6_SCAN))
    .word ((B7_MT<<15)+(B7_Trcd<<2)+(B7_SCAN))
    .word ((REFEN<<23)+(TREFMD<<22)+(Trp<<20)+(Trc<<18)+(Tchr<<16)+REFCNT)
    .word 0x31
    .word 0x30
    .word 0x30
   
8）在board/bks2410加入NAND Flash读函数，建立nand_read.c，加入如下内容(copy from vivi)：
#include <config.h>
#define __REGb(x) (*(volatile unsigned char *)(x))
#define __REGi(x) (*(volatile unsigned int *)(x))
#define NF_BASE  0x4e000000
#define NFCONF  __REGi(NF_BASE + 0x0)
#define NFCMD  __REGb(NF_BASE + 0x4)
#define NFADDR  __REGb(NF_BASE + 0x8)
#define NFDATA  __REGb(NF_BASE + 0xc)
#define NFSTAT  __REGb(NF_BASE + 0x10)
#define BUSY 1
inline void wait_idle(void) {
    int i;
    while(!(NFSTAT & BUSY))
      for(i=0; i<10; i++);
}
#define NAND_SECTOR_SIZE 512
#define NAND_BLOCK_MASK  (NAND_SECTOR_SIZE - 1)
/* low level nand read function */
int
nand_read_ll(unsigned char *buf, unsigned long start_addr, int size)
{
    int i, j;
    if ((start_addr & NAND_BLOCK_MASK) || (size & NAND_BLOCK_MASK)) {
        return -1; /* invalid alignment */
    }
    /* chip Enable */
    NFCONF &= ~0x800;
    for(i=0; i<10; i++);
    for(i=start_addr; i < (start_addr + size);) {
      /* READ0 */
      NFCMD = 0;
      /* Write Address */
      NFADDR = i & 0xff;
      NFADDR = (i >> 9) & 0xff;
      NFADDR = (i >> 17) & 0xff;
      NFADDR = (i >> 25) & 0xff;
      wait_idle();
      for(j=0; j < NAND_SECTOR_SIZE; j++, i++) {
 *buf = (NFDATA & 0xff);
 buf++;
      }
    }
    /* chip Disable */
    NFCONF |= 0x800; /* chip disable */
    return 0;
}
9）修改board/bks2410/Makefile为
OBJS := bks2410.o flash.o nand_read.o
10）修改cpu/arm920t/start.S文件
在ldr pc, _start_armboot之前加入：
#ifdef CONFIG_S3C2410_NAND_BOOT
  bl    copy_myself
 
  @ jump to ram
  ldr   r1, =on_the_ram
  add  pc, r1, #0
  nop
  nop
  1:    b     1b          @ infinite loop
 
on_the_ram:
#endif
在_start_armboot: .word start_armboot之后加入：
#ifdef CONFIG_S3C2410_NAND_BOOT
copy_myself:
  mov r10, lr
@ reset NAND
  mov r1, #NAND_CTL_BASE
  ldr   r2, =0xf830           @ initial value
  str   r2, [r1, #oNFCONF]
  ldr   r2, [r1, #oNFCONF]
  bic  r2, r2, #0x800              @ enable chip
  str   r2, [r1, #oNFCONF]
  mov r2, #0xff         @ RESET command
  strb r2, [r1, #oNFCMD]
  mov r3, #0                   @ wait
1:add  r3, r3, #0x1
  cmp r3, #0xa
  blt   1b
2:ldr   r2, [r1, #oNFSTAT]      @ wait ready
  tst    r2, #0x1
  beq  2b
  ldr   r2, [r1, #oNFCONF]
  orr  r2, r2, #0x800              @ disable chip
  str   r2, [r1, #oNFCONF]
@ get read to call C functions (for nand_read())
  ldr   sp, DW_STACK_START       @ setup stack pointer
  mov fp, #0                    @ no previous frame, so fp=0
@ copy vivi to RAM
  ldr   r0, =UBOOT_RAM_BASE
  mov     r1, #0x0
  mov r2, #0x20000
  bl    nand_read_ll
  tst    r0, #0x0
  beq  ok_nand_read
#ifdef CONFIG_DEBUG_LL
  bad_nand_read:
  ldr   r0, STR_FAIL
  ldr   r1, SerBase
  bl    PrintWord
1:b     1b          @ infinite loop
  #endif
ok_nand_read:
#ifdef CONFIG_DEBUG_LL
  ldr   r0, STR_OK
  ldr   r1, SerBase
  bl    PrintWord
#endif
@ verify
  mov r0, #0
  ldr   r1, =UBOOT_RAM_BASE
  mov r2, #0x400     @ 4 bytes * 1024 = 4K-bytes
go_next:
  ldr   r3, [r0], #4
  ldr   r4, [r1], #4
  teq   r3, r4
  bne  notmatch
  subs r2, r2, #4
  beq  done_nand_read
  bne  go_next
notmatch:
#ifdef CONFIG_DEBUG_LL
  sub  r0, r0, #4
  ldr   r1, SerBase
  bl    PrintHexWord
  ldr   r0, STR_FAIL
  ldr   r1, SerBase
  bl    PrintWord
#endif
1:b     1b
done_nand_read:
#ifdef CONFIG_DEBUG_LL
  ldr   r0, STR_OK
  ldr   r1, SerBase
  bl    PrintWord
#endif
  mov pc, r10
@ clear memory
@ r0: start address
@ r1: length
  mem_clear:
  mov r2, #0
  mov r3, r2
  mov r4, r2
  mov r5, r2
  mov r6, r2
  mov r7, r2
  mov r8, r2
  mov r9, r2
clear_loop:
  stmia      r0!, {r2-r9}
  subs r1, r1, #(8 * 4)
  bne  clear_loop
  mov pc, lr
#endif @ CONFIG_S3C2410_NAND_BOOT
在文件的最后加入：
   .align     2
DW_STACK_START:
 .word      STACK_BASE+STACK_SIZE-4
11）修改include/configs/bks2410.h文件，添加如下内容：
/*
 * Nandflash Boot
 */
#define CONFIG_S3C2410_NAND_BOOT 1
#define STACK_BASE    0x33f00000
#define STACK_SIZE    0x8000
#define UBOOT_RAM_BASE    0x33f80000
/* NAND Flash Controller */
#define NAND_CTL_BASE            0x4E000000
#define bINT_CTL(Nb)        __REG(INT_CTL_BASE + (Nb))
/* Offset */
#define oNFCONF               0x00
#define oNFCMD                0x04
#define oNFADDR               0x08
#define oNFDATA               0x0c
#define oNFSTAT               0x10
#define oNFECC                0x14
12）重新编译u-boot
make all ARCH=arm
13）通过jtag将u-boot烧写到flash中就可以从NAND flash启动了
我的u-boot启动信息：
U-Boot 1.1.3 (May  6 2006 - 18:13:59)
U-Boot code: 33F80000 -> 33F967C4  BSS: -> 33F9AAAC
RAM Configuration:
Bank #0: 30000000 64 MB
Flash: 512 kB
*** Warning - bad CRC, using default environment
In:    serial
Out:   serial
Err:   serial
BKS2410 #