在openwrt下对华为WA633无线AP的千兆网卡驱动进行支持

1.下面是这款AP的全裸图，AP的无线网卡采用了AR9223，PHY采用了博通的BCM5461，主控CPU位octeon+ 500，射频功放采用的是RF5602方案。由于这款CPU并不常见，我至今未在网上找到它的datasheet，导致我们在玩这款AP的过程中遇到了很多困难。

2.Openwrt源码采用的最新的，B...b,内核是Linux-3.10.49

3.在内核里我们可以看到有支持BCM5461的驱动，但是我们选上了之后并不能直接用，因为这块板子上的PHY与CPU间通过MIDO和RGMI两种总线方式(可能描述有误，记不清了)进行数据交互。但是主控芯片上有多个同意的接口供外设使用，但是这块板子上只用了一个，我们必须去确定用的是那个口，然后在内核加载过程中做相应处理。

4.修改内核源码，创建一个新的patch,将所有的改动保存在patch中。

Index: linux-3.10.49/arch/mips/cavium-octeon/executive/cvmx-helper-board.c
===================================================================
--- linux-3.10.49.orig/arch/mips/cavium-octeon/executive/cvmx-helper-board.c	2015-11-18 01:28:11.483050038 +0800
+++ linux-3.10.49/arch/mips/cavium-octeon/executive/cvmx-helper-board.c	2015-11-18 01:28:11.559050042 +0800
@@ -93,13 +93,8 @@
 	case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
 	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
 	case CVMX_BOARD_TYPE_CN3020_EVB_HS5:
-		/*
-		 * Port 0 is WAN connected to a PHY, Port 1 is GMII
-		 * connected to a switch
-		 */
+		/* Port 0 is WAN connected to a PHY:BCM5461(For WA633) */
 		if (ipd_port == 0)
-			return 4;
-		else if (ipd_port == 1)
 			return 9;
 		else
 			return -1;
@@ -244,11 +239,8 @@
 	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
 	case CVMX_BOARD_TYPE_CN3020_EVB_HS5:
 		/* Port 1 on these boards is always Gigabit */
-		if (ipd_port == 1) {
-			result.s.link_up = 1;
-			result.s.full_duplex = 1;
-			result.s.speed = 1000;
-			return result;
+		if (ipd_port == 0) {
+			is_broadcom_phy = 1;
 		}
 		/* Fall through to the generic code below */
 		break;
Index: linux-3.10.49/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c
===================================================================
--- linux-3.10.49.orig/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c	2014-07-18 06:58:15.000000000 +0800
+++ linux-3.10.49/arch/mips/cavium-octeon/executive/cvmx-helper-rgmii.c	2015-11-18 01:28:11.559050042 +0800
@@ -72,7 +72,7 @@
 			 * On these chips "type" says we're in
 			 * GMII/MII mode. This limits us to 2 ports
 			 */
-			num_ports = 2;
+			num_ports = 1;
 		} else {
 			cvmx_dprintf("ERROR: Unsupported Octeon model in %s\n",
 				     __func__);
@@ -84,7 +84,7 @@
 		} else if (OCTEON_IS_MODEL(OCTEON_CN31XX)
 			   || OCTEON_IS_MODEL(OCTEON_CN30XX)
 			   || OCTEON_IS_MODEL(OCTEON_CN50XX)) {
-			num_ports = 3;
+			num_ports = 1;
 		} else {
 			cvmx_dprintf("ERROR: Unsupported Octeon model in %s\n",
 				     __func__);
Index: linux-3.10.49/arch/mips/pci/pci-octeon.c
===================================================================
--- linux-3.10.49.orig/arch/mips/pci/pci-octeon.c	2014-07-18 06:58:15.000000000 +0800
+++ linux-3.10.49/arch/mips/pci/pci-octeon.c	2015-11-20 11:24:27.655865439 +0800
@@ -211,7 +211,7 @@
 	case CVMX_BOARD_TYPE_EBH3100:
 	case CVMX_BOARD_TYPE_CN3010_EVB_HS5:
 	case CVMX_BOARD_TYPE_CN3005_EVB_HS5:
-		return "AAABAAAAAAAAAAAAAAAAAAAAAAAAAAAA";
+		return "AAAAAAAAAAAAAABAAAAAAAAAAAAAAABA";
 	case CVMX_BOARD_TYPE_BBGW_REF:
 		return "AABCD";
 	case CVMX_BOARD_TYPE_THUNDER:

5.需要改的几个地方，改天贴图，还有内核里必选的几个配置项。