linux 串口示波器,求大神指点visual scope串口示波器怎么用？-CSDN博客

这篇博客介绍了如何使用VisualScope串口示波器进行STM32与MPU之间的通信。文章详细阐述了CRC16校验的计算方法，并给出了STM32接收和发送数据的中断服务例程。通过CRC校验确保数据传输的准确性，同时展示了MPU接收和处理数据的代码，包括地址解析和数据打包过程。

摘要由CSDN通过智能技术生成

求大神指点怎么使用visual scope串口示波器，软件自带的协议看不懂，初学者，希望能详细的讲讲！如何利用协议实现STM32 的波形显示。这是协议，求大神指点啊

Data send adapt CRC16 verification,The following is the function of CRC16,please refer

//-------------------------------------------------------------------------------------------

unsigned short CRC_CHECK(unsigned char *Buf, unsigned char CRC_CNT)

{

unsigned short CRC_Temp;

unsigned char i,j;

CRC_Temp = 0xffff;

for (i=0;i

CRC_Temp ^= Buf;

for (j=0;j<8;j++) {

if (CRC_Temp & 0x01)

CRC_Temp = (CRC_Temp >>1 ) ^ 0xa001;

else

CRC_Temp = CRC_Temp >> 1;

}

return(CRC_Temp);

}

//-------------------------------------------------------------------------------------------

The data from computer to MPU is like this:

Ch1_Addr_LL，Ch1_Addr_LH，

Ch1_Addr_HL，Ch1_Addr_HH，

Ch2_Addr_LL，Ch2_Addr_LH，

Ch2_Addr_HL，Ch2_Addr_HH，

Ch3_Addr_LL，Ch3_Addr_LH，

Ch3_Addr_HL，Ch3_Addr_HH，

Ch4_Addr_LL，Ch4_Addr_LH，

Ch4_Addr_HL，Ch4_Addr_HH，

CRC16_L，CRC16_H

//-------------------------------------------------------------------------------------------

The data from MPU to computer should be like this:

Ch1Data_L，Ch1Data_H，

Ch2Data_L，Ch2Data_H，

Ch3Data_L，Ch3Data_H，

Ch4Data_L，Ch4Data_H，

CRC16_L，CRC16_H

//-------------------------------------------------------------------------------------------

the following is MPU code,please refer.

//-------------------------------------------------------------------------------------------

#define RxCountMax 18

unsigned short RxBuf[RxCountMax];

unsigned short TxBuf[10];

unsigned short RxCnt;

unsigned short TxCnt;

unsigned short Rx50msCnt;

unsigned long pAddr1,pAddr2,pAddr3,pAddr4;

//Receive interrupt routine

void voRxIsr(void)

{

unsigned short i,CRC_RX,CRC_Tmp;

RxBuf[RxCnt] = Rx.data; //acquire data

RxCnt++;

if(RxCnt == RxCountMax) {

CRC_Tmp = CRC_CHECK(RxBuf,16); //CRC Calculation

CRC_RX = ((unsigned short)RxBuf[RxCountMax-1]<<8) + RxBuf[RxCountMax-2];

if(CRC_Tmp == CRC_RX){

pAddr1 = ((ULONG)(RxBuf[0x3])<<24)|((ULONG)(RxBuf[0x2])<<16)|((ULONG)(RxBuf[0x1])<<8)|RxBuf[0x0];

pAddr2 = ((ULONG)(RxBuf[0x7])<<24)|((ULONG)(RxBuf[0x6])<<16)|((ULONG)(RxBuf[0x5])<<8)|RxBuf[0x4];

pAddr3 = ((ULONG)(RxBuf[0xB])<<24)|((ULONG)(RxBuf[0xA])<<16)|((ULONG)(RxBuf[0x9])<<8)|RxBuf[0x8];

pAddr4 = ((ULONG)(RxBuf[0xF])<<24)|((ULONG)(RxBuf[0xE])<<16)|((ULONG)(RxBuf[0xD])<<8)|RxBuf[0xC];

}

RxCnt = 0;

}

Rx50msCnt = 0;

//to add--Clear Receive Data Register Fll flag; //clear Receive Data Register Full flag

}

//-------------------------------------------------------------------------------------------

//Transfer interrupt routine

void voTxIsr(void)

{

if(TxCnt <= 9){

Tx.Register = TxBuf[TxCnt];

//Clear Tx interrupt flag

TxCnt++;

if(TxCnt >= 10){

//send interrupt disable

}

//-------------------------------------------------------------------------------------------

//Monitor routine Execute every T Period time

void voMonitor(void)

{

unsigned short ChxData[4],CRC_Tmp,i;

Rx50msCnt++;

if(Rx50msCnt >=500) {

RxCnt = 0;

Rx50msCnt = 0;

}

ChxData[0].sw = *(unsigned short *)pAddr1;

ChxData[1].sw = *(unsigned short *)pAddr2;

ChxData[2].sw = *(unsigned short *)pAddr3;

ChxData[3].sw = *(unsigned short *)pAddr4;

for(i=0;i<4;i++){

TxBuf[2*i+0] = ChxData.sb.low; // chlow byte

TxBuf[2*i+1] = ChxData.sb.hi; // chhi byte

}

CRC_Tmp = CRC_CHECK(TxBuf,8);

TxBuf[8] = CRC_Tmp&0xff;

TxBuf[9] = CRC_Tmp>>8;

//send first data

Tx.Register = TxBuf[0]; //send begin

//Enalbe TXD interrupt

TxCnt = 1;

}

//-------------------------------------------------------------------------------------------