在 "光盘资料 -> 烧写工具 -> 裸机 -> eop&op" 目录下可以获取本篇文章所有相关驱动文件。
一、安装 oflash
oflash 安装包路径:eop&op -> 调试工具 -> 01.OpenOCD with GUI setup.exe
使用管理员权限安装 OpenOCD with GUI setup.exe 即可在 cmd.exe 命令行里执行 oflash 程序。
验证驱动 oflash 是否安装成功,依次执行:Win + R -> 输入 cmd 调起控制台 -> 输入 oflash 执行,出现以下提示说明 oflash 安装成功。
C:\Users\user>oflash +---------------------------------------------------------+ | Flash Programmer v1.5.2 for OpenJTAG of www.100ask.net| | OpenJTAG is a USB to JTAG & RS232 tool based FT2232 | | This programmer supports both of S3C24X0 & S3C6410 | | Author: Email/MSN(thisway.diy@163.com), QQ(17653039) | +---------------------------------------------------------+ Usage: 1. oflash, run with cfg.txt or prompt 2. oflash [file], write [file] to flash with prompt 3. oflash [-f config_file] 4. oflash [jtag_type] [cpu_type] [flash_type] [read_or_write] [offset] [file] Can't open cfg.txt, you should follow the prompt Select the JTAG type: 0. OpenJTAG 1. Dongle JTAG(parallel port) 2. Wiggler JTAG(parallel port) Enter the number:
二、安装 OpenJTAG 驱动
将 OpenJTAG 插入电脑 -> 右键我的电脑 -> 管理 -> 设备管理器,可以看到其他设备里面有两个 USB <==> JTAG&&RS232 设备。但是旁边有感叹号,说明这个两个设备并没有驱动。
右键 USB <==> JTAG&&RS232 -> 更新驱动程序 -> 浏览计算机以查找驱动程序 -> 选择 "光盘资料/烧写工具/裸机/eop&op/驱动/OpenJTAG" -> 点击下一步,开始安装驱动。
很遗憾,没装上,报了一个这样的错,这是什么鬼?
怎么办? 禁止验证驱动签名即可安装上此驱动。
开始菜单 -> 设置 -> 更新和安全 -> 恢复 -> 立即重启 -> 疑难解答 -> 高级选项 -> 启动设置 -> 重启 -> 电脑重启后,出现选择界面,F7选择禁止验证驱动签名。
然后重新更新 USB <==> JTAG&&RS232 的驱动程序,注意需要更新三次,因为 OpenJTAG 很强大,同时是三个设备。
三个驱动分别是:
三、使用 oflash 烧写 U-Boot
将编译好的 u-boot.bin 文件从虚拟机复制到 Windows 任意目录下。cmd 切换到此目录下,使用 oflash 命令烧写:
C:\Users\user\Desktop>oflash u-boot.bin +---------------------------------------------------------+ | Flash Programmer v1.5.2 for OpenJTAG of www.100ask.net | | OpenJTAG is a USB to JTAG & RS232 tool based FT2232 | | This programmer supports both of S3C24X0 & S3C6410 | | Author: Email/MSN(thisway.diy@163.com), QQ(17653039) | +---------------------------------------------------------+ Usage: 1. oflash, run with cfg.txt or prompt 2. oflash [file], write [file] to flash with prompt 3. oflash [-f config_file] 4. oflash [jtag_type] [cpu_type] [flash_type] [read_or_write] [offset] [file] Select the JTAG type: 0. OpenJTAG 1. Dongle JTAG(parallel port) 2. Wiggler JTAG(parallel port) Enter the number: 0 Select the CPU: 0. S3C2410 1. S3C2440 2. S3C6410 Enter the number: 1 device: 4 "2232C" deviceID: 0x14575118 SerialNumber: FThecwJmA Description: USB<=>JTAG&RS232 AS3C2440 detected, cpuID = 0x0032409d [Main Menu] 0:Nand Flash prog 1:Nor Flash prog 2:Memory Rd/Wr 3:Exit Select the function to test:0 [NAND Flash JTAG Programmer] Scan nand flash: Device 0: NAND 256MiB 3,3V 8-bit, sector size 128 KiB Total size: 256 MiB 0:Nand Flash Program 1:Nand Flash Print BlkPage 2:Exit Select the function to test :0 [NAND Flash Writing Program] Source size: 0x306ac Available target block number: 0~2047 Input target block number:0 target start block number =0 target size (0x20000*2) =0x40000 STATUS: Epppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppppp Eppppppppppppppppppppppppppppppppp