/**
* usb_submit_urb - issue an asynchronous transfer request for an endpoint
* @urb: pointer to the urb describing the request
* @mem_flags: the type of memory to allocate, see kmalloc() for a list
* of valid options for this.
*
* This submits a transfer request, and transfers control of the URB
* describing that request to the USB subsystem. Request completion will
* be indicated later, asynchronously, by calling the completion handler.
* The three types of completion are success, error, and unlink
* (a software-induced fault, also called "request cancellation").
*
* URBs may be submitted in interrupt context.
*
* The caller must have correctly initialized the URB before submitting
* it. Functions such as usb_fill_bulk_urb() and usb_fill_control_urb() are
* available to ensure that most fields are correctly initialized, for
* the particular kind of transfer, although they will not initialize
* any transfer flags.
*
* Successful submissions return 0; otherwise this routine returns a
* negative error number. If the submission is successful, the complete()
* callback from the URB will be called exactly once, when the USB core and
* Host Controller Driver (HCD) are finished with the URB. When the completion
* function is called, control of the URB is returned to the device
* driver which issued the request. The completion handler may then
* immediately free or reuse that URB.
*
* With few exceptions, USB device drivers should never access URB fields
* provided by usbcore or the HCD until its complete() is called.
* The exceptions relate to periodic transfer scheduling. For both
* interrupt and isochronous urbs, as part of successful URB submission
* urb->interval is modified to reflect the actual transfer period used
* (normally some power of two units). And for isochronous urbs,
* urb->start_frame is modified to reflect when the URB's transfers were
* scheduled to start. Not all isochronous transfer scheduling policies
* will work, but most host controller drivers should easily handle ISO
* queues going from now until 10-200 msec into the future.
*
* For control endpoints, the synchronous usb_control_msg() call is
* often used (in non-interrupt context) instead of this call.
* That is often used through convenience wrappers, for the requests
* that are standardized in the USB 2.0 specification. For bulk
* endpoints, a synchronous usb_bulk_msg() call is available.
*
* Request Queuing:
*
* URBs may be submitted to endpoints before previous ones complete, to
* minimize the impact of interrupt latencies and system overhead on data
* throughput. With that queuing policy, an endpoint's queue would never
* be empty. This is required for continuous isochronous data streams,
* and may also be required for some kinds of interrupt transfers. Such
* queuing also maximizes bandwidth utilization by letting USB controllers
* start work on later requests before driver software has finished the
* completion processing for earlier (successful) requests.
*
* As of Linux 2.6, all USB endpoint transfer queues support depths greater
* than one. This was previously a HCD-specific behavior, except for ISO
* transfers. Non-isochronous endpoint queues are inactive during cleanup
* after faults (transfer errors or cancellation).
*
* Reserved Bandwidth Transfers:
*
* Periodic transfers (interrupt or isochronous) are performed repeatedly,
* using the interval specified in the urb. Submitting the first urb to
* the endpoint reserves the bandwidth necessary to make those transfers.
* If the USB subsystem can't allocate sufficient bandwidth to perform
* the periodic request, submitting such a periodic request should fail.
*
* Device drivers must explicitly request that repetition, by ensuring that
* some URB is always on the endpoint's queue (except possibly for short
* periods during completion callacks). When there is no longer an urb
* queued, the endpoint's bandwidth reservation is canceled. This means
* drivers can use their completion handlers to ensure they keep bandwidth
* they need, by reinitializing and resubmitting the just-completed urb
* until the driver longer needs that periodic bandwidth.
*
* Memory Flags:
*
* The general rules for how to decide which mem_flags to use
* are the same as for kmalloc. There are four
* different possible values; GFP_KERNEL, GFP_NOFS, GFP_NOIO and
* GFP_ATOMIC.
*
* GFP_NOFS is not ever used, as it has not been implemented yet.
*
* GFP_ATOMIC is used when
* (a) you are inside a completion handler, an interrupt, bottom half,
* tasklet or timer, or
* (b) you are holding a spinlock or rwlock (does not apply to
* semaphores), or
* (c) current->state != TASK_RUNNING, this is the case only after
* you've changed it.
*
* GFP_NOIO is used in the block io path and error handling of storage
* devices.
*
* All other situations use GFP_KERNEL.
*
* Some more specific rules for mem_flags can be inferred, such as
* (1) start_xmit, timeout, and receive methods of network drivers must
* use GFP_ATOMIC (they are called with a spinlock held);
* (2) queuecommand methods of scsi drivers must use GFP_ATOMIC (also
* called with a spinlock held);
* (3) If you use a kernel thread with a network driver you must use
* GFP_NOIO, unless (b) or (c) apply;
* (4) after you have done a down() you can use GFP_KERNEL, unless (b) or (c)
* apply or your are in a storage driver's block io path;
* (5) USB probe and disconnect can use GFP_KERNEL unless (b) or (c) apply; and
* (6) changing firmware on a running storage or net device uses
* GFP_NOIO, unless b) or c) apply
*
*/
转载于:https://www.cnblogs.com/zxc2man/p/6647165.html