Linux如何查看硬盘型号和缓存

Linux如何查看硬盘型号和缓存？方法：hdparm  -i /dev/sda1

hdparm  -i /dev/sda1

/dev/sda1:

 Model=WDC WD10EACS-00ZJB0  （硬盘型号）                   , FwRev=01.01B01, SerialNo=     WD-WCASJ0976997
 Config={ HardSect NotMFM HdSw>15uSec SpinMotCtl Fixed DTR>5Mbs FmtGapReq }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=50
 BuffType=unknown, BuffSize=16384kB（硬盘缓存）, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2
 AdvancedPM=no www.ctohome.com WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

 * signifies the current active mode

 

[root@host96 www.ctohome.com]# hdparm  -i /dev/sda1

/dev/sda1:

 Model=Hitachi HDT721010SLA360                 , FwRev=ST6OA31B, SerialNo=      STF604MR2DG61P
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=56
 BuffType=DualPortCache, BuffSize=15001kB, MaxMultSect=16, MultSect=?16?
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:120,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: unknown:  ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7

 * signifies the current active mode

 

linux/centos系统的服务器如何用hdparm测试硬盘性能，测试硬盘速度？

[root@host88 www.ctohome.com]# hdparm -tT /dev/sda8

/dev/sda8:
 Timing cached reads:   8512 MB in  2.00 seconds = 4262.60 MB/sec
 Timing buffered disk reads:  222 MB in  3.02 seconds =  73.58 MB/sec

[root@host96 www.ctohome.com]# hdparm -tT /dev/sda2

/dev/sda2:
 Timing cached reads:   7684 MB in  2.00 seconds = 3848.10 MB/sec
 Timing buffered disk reads:  116 MB in  3.15 seconds =  36.82 MB/sec

 

注意，hdparm -tT 必须要在机器空闲的时候测试才准确，机器繁忙的时候是测不准的。如果有小于20MB/Sec的结果，那么磁盘的IO性能就不怎么样了。

转载于:https://www.cnblogs.com/feihongwuhen/archive/2010/07/29/7170406.html