6410UBOOT学习：
上电开始，硬件自动取Bootloader前4K的内容放到Steppingstone中，Steppingstone其实是个SRAM，而不是SDRAM，大小8K。并且物理地址的零地址也映射在这儿，用于复位时用。这个sram也就是esram，原来物理地址是0x0c00_0000-0x0fff_ffff,用作nandflash启动时，会被重映射为零地址，就是2个物理地址映射到同一个地方。
在Steppingstone中开始执行拷贝过来的代码，包括start.S（这只是bootloader的一部分），做了上图第一阶段的工作，其中拷贝的代码只是整个bootloader，拷贝到SDRAM中，而不是内核镜像。拷贝结束后就在SDRAM中运行，不过第一阶段还会执行一遍，start.S中的汇编部分会判断代码在Steppingstone还是在SDRAM中，从而选择不同的分支执行。就是对于要不要拷贝代码做出选择。在执行完第二阶段就会拷贝内核代码，通过函数调用直接进入内核执行，这样就完成了内核的引导启动过程。
解释下地址映射，这个物理地址为什么对应这个设备，与硬件逻辑有关，是否可以重新映射也是需要硬件支持的。所以你可以给一个实际存储块2个不同物理地址，这是可行的。
上面说的都是物理地址，当启动MMU后，就会使用虚拟地址，一般PC机中虚拟地址只是针对内存而言的，并不对应存储设备，如硬盘。访问块设备一般需要使用文件系统。
其中SDRAM中的UBOOT镜像就是start.S中拷贝过去的。SDRAM称之为内存。作为内存有堆区，有栈区，有全局变量区，有中断向量表区，有引导代码区，还有后来用户程序进来存放的区域。提到了内存就要说起MMU，开启了MMU，以后就都开始使用虚拟地址了。
6410 start.S
#include <config.h>
#include <version.h>
#ifdef CONFIG_ENABLE_MMU
#include <asm/proc/domain.h>
#endif
#include <regs.h>
#ifndef CONFIG_ENABLE_MMU
#ifndef CFG_PHY_UBOOT_BASE
#define CFG_PHY_UBOOT_BASE CFG_UBOOT_BASE
#endif
#endif
/*
*************************************************************************
*
* Jump vector table as in table 3.1 in [1]
*
*************************************************************************
*/
// 这是在定义u-boot的启动定义入口点，汇编程序的缺省入口是 start标号，用户也可以在连接脚本文件中用ENTRY标志指明其它入口点。
.globl _start
_start: b reset //复位向量 复位 0x0 用b跳转，是因为在MMU启动之前就要跳转，所以跟其他的异常不一样
ldr pc, _undefined_instruction //未定义的指令异常 0x4
ldr pc, _software_interrupt //软件中断异常 0x8
ldr pc, _prefetch_abort //预取指令 0xc
ldr pc, _data_abort //数据 0x10
ldr pc, _not_used //未使用 0x14
ldr pc, _irq //慢速中断异常 0x18
ldr pc, _fiq //快速中断异常 0x1c
_undefined_instruction:
.word undefined_instruction //假设undefined_instruction是0x0000ffff，这个数据会根据平台产生，然后把undefined_instruction的值给PC
_software_interrupt:
.word software_interrupt //.word伪操分配了一段字内存单元（分配的单元都是字对齐的），并用伪操作中的Start进行初始化（.long和.int作用与之类似）
_prefetch_abort:
.word prefetch_abort //把一个常量赋值给一个变量。所谓分配内存单元，就好比int时，占有4个字节内存一样。
_data_abort:
.word data_abort
_not_used:
.word not_used
_irq:
.word irq
_fiq:
.word fiq
_pad:
.word 0x12345678 /* now 16*4=64 */
.global _end_vect
_end_vect:
.balignl 16,0xdeadbeef //将地址对齐到16的倍数，为了对齐而空闲的部分是用后面的值填充
/*
*************************************************************************
*
* Startup Code (reset vector)
*
* do important init only if we don't start from memory! 如果在ram中执行，就不要拷贝代码了 比如说复位
* setup Memory and board specific bits prior to relocation.
* relocate armboot to ram
* setup stack
*
*************************************************************************
*/
_TEXT_BASE:
.word TEXT_BASE//TEXT_BASE在开发板相关的目录中的/u-boot-1.1.6/board/smdk2410/config.mk文档中定义,他定义了代码在运行时所在的地址,那么_TEXT_BASE中保存了这个地址
//TEXT_BASE基地址没有MMU时就是物理地址0x57e00000，有MMU时对应的虚拟地址就是0xc7e00000
/*
* Below variable is very important because we use MMU in U-Boot.
* Without it, we cannot run code correctly before MMU is ON.
* by scsuh.
*/
_TEXT_PHY_BASE:
.word CFG_PHY_UBOOT_BASE //这个是宏定义的 UBOOT在SDRAM中的物理地址 0x57e0_0000
.globl _armboot_start
_armboot_start:
.word _start
/*
* These are defined in the board-specific linker script.
*/
.globl _bss_start
_bss_start:
.word __bss_start
.globl _bss_end
_bss_end:
.word _end
#ifdef CONFIG_USE_IRQ
/* IRQ stack memory (calculated at run-time) */
.globl IRQ_STACK_START
IRQ_STACK_START:
.word 0x0badc0de //把0x0badc0de赋值给变量IRQ_STACK_START
/* IRQ stack memory (calculated at run-time) */
.globl FIQ_STACK_START
FIQ_STACK_START:
.word 0x0badc0de
#endif
/*
* the actual reset code
*/
//上电或复位后都跳到这里，但是执行的地址不一样 nandflash启动的时候，物理地址零地址映射到SRAM
reset:
/*
* set the cpu to SVC32 mode 操作系统使用的保护模式
*/
mrs r0,cpsr //cpsr中的值放到ro中去
bic r0,r0,#0x1f //清除低5位为0
orr r0,r0,#0xd3 //或运算 相应位置位
msr cpsr,r0 //更新cpsr专用寄存器
//实现了两个功能.1,disable 外部中断(IRQ)与快速中断(FIR).2,把系统设为SVC32状态(超级保护)即M4~M1=10011。
/*
*************************************************************************
*
* CPU_init_critical registers
*
* setup important registers
* setup memory timing
*
*************************************************************************
*/
/*
* we do sys-critical inits only at reboot,
* not when booting from ram!
*/
cpu_init_crit://主频的初始化 和 相关控制器的初始化，比如SDRAM
/*
* flush v4 I/D caches
*/
mov r0, #0
/* 使I/D cache失效：将寄存器r0的数据传送到协处理器p15的c7中。C7寄存器位对应cp15中的cache控制寄存器 */
mcr p15, 0, r0, c7, c7, 0 /* flush v3/v4 cache */
/* 使TLB操作寄存器失效：将r0数据送到cp15的c8、c7中。C8对应TLB操作寄存器 */
mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
/*
* disable MMU stuff and caches
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002300 @ clear bits 13, 9:8 (--V- --RS)
bic r0, r0, #0x00000087 @ clear bits 7, 2:0 (B--- -CAM)
orr r0, r0, #0x00000002 @ set bit 2 (A) Align
orr r0, r0, #0x00001000 @ set bit 12 (I) I-Cache
mcr p15, 0, r0, c1, c0, 0
/* Peri port setup */
/* 通过CP15 c15 设置外设基地址为0x70000000，地址空间为256M
*
* Base Address UPN/SBZ SIZE
* |31----------12|11---5 | 4--0|
*
* 0x13 Means b10011 b10011 = 256MB
*
*/
ldr r0, =0x70000000
orr r0, r0, #0x13
mcr p15,0,r0,c15,c2,4 @ 256M(0x70000000-0x7fffffff)
#ifdef CONFIG_BOOT_ONENAND
ldr r0, =0x70000000 @ onenand controller setup
orr r0, r0, #0x100000
ldr r1, =0x4000
orr r1, r1, #0xe0
str r1, [r0]
#if defined(CONFIG_S3C6410) || defined(CONFIG_S3C6430)
orr r0, r0, #300 @ disable watchdog 失能看门狗
mov r1, #1
str r1, [r0]
mov r1, #0x23000000 @ start buffer register
orr r1, r1, #0x30000
orr r1, r1, #0xc800
#else
mov r1, =0x20000000 @ start buffer register
orr r1, r1, #0xc30000
orr r1, r1, #0xc800
#endif
sub r0, r1, #0x0400 @ start address1 register
ldr r2, [r1, #0x84] @ ecc bypass
orr r2, r2, #0x100
str r2, [r1, #0x84]
mov r3, #0x0 @ DFS, FBA
str r3, [r0, #0x00]
str r3, [r0, #0x04] @ select dataram for DDP as 0
mov r4, #0x104 @ interrupt register
mov r5, #0x0002 @ FPA, FSA
mov r6, #0x0800 @ BSA
onenand_bl1_load:
str r5, [r0, #0x1c] @ save FPA, FSA
orr r6, r6, #0x02 @ BSC
str r6, [r1, #0x00] @ save BSA, BSC
str r3, [r1, r4] @ clear interrupt
str r3, [r1, #0x80] @ write load command
mov r7, #0x100 @ need small delay
onenand_wait_loop1:
subs r7, r7, #0x1
bne onenand_wait_loop1
add r5, r5, #0x2 @ next FPA, FSA
sub r6, r6, #0x2
add r6, r6, #0x200 @ next BSA
cmp r5, #0x8
bne onenand_bl1_load
#endif
/*
* Go setup Memory and board specific bits prior to relocation.
*/
//上面的属于特殊配置吧 ifdef控制的 可有可无
//执行位于board/samsung/smdk6410/lowlevel_init.S内的lowlevel_init子程序，设置时钟相关的PLL，MUX和内存
bl lowlevel_init /* go setup pll,mux,memory */
/* when we already run in ram, we don't need to relocate（搬迁） U-Boot.测试的时候不需要拷贝
* and actually, memory controller must be configured before U-Boot
* is running in ram.
*/
ldr r0, =0xff000fff
bic r1, pc, r0 /* r0 <- current base addr of code */
ldr r2, _TEXT_BASE /* r1 <- original base addr in ram */
bic r2, r2, r0 /* r0 <- current base addr of code */
cmp r1, r2 /* compare r0, r1 */
beq after_copy /* r0 == r1 then skip flash copy */
#ifdef CONFIG_BOOT_NOR /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_PHY_BASE /* r1 <- destination */
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
nor_copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end addreee [r2] */
ble nor_copy_loop
b after_copy
#endif
#ifdef CONFIG_BOOT_NAND
mov r0, #0x1000
bl copy_from_nand //调用copy_from_nand子程序
#endif
#ifdef CONFIG_BOOT_MOVINAND
ldr sp, _TEXT_PHY_BASE
bl movi_bl2_copy
b after_copy
#endif
#ifdef CONFIG_BOOT_ONENAND
ldr sp, =0x50000000 @ temporary stack
#ifdef CONFIG_S3C6400
mov r1, =0x20000000 @ start buffer register
orr r1, r1, #0xc30000
orr r1, r1, #0xc800
#else
mov r1, #0x23000000 @ start buffer register
orr r1, r1, #0x30000
orr r1, r1, #0xc800
#endif
ldr r2, [r1, #0x84] @ ecc bypass
orr r2, r2, #0x100
str r2, [r1, #0x84]
sub r0, r1, #0x0400 @ start address1 register
str r3, [r0, #0x00]
str r3, [r0, #0x04] @ select dataram for DDP as 0
mov r4, #0x104 @ interrupt register
mov r6, #0x0c00 @ fixed dataram1 sector number
str r6, [r1, #0x00]
mov r3, #0x0 @ DFS, FBA
mov r5, #0x0000 @ FPA, FSA
ldr r9, =CFG_PHY_UBOOT_BASE @ destination
onenand_bl2_load:
str r3, [r0, #0x00] @ save DFS, FBA
str r5, [r0, #0x1c] @ save FPA, FSA
mov r7, #0x0 @ clear interrupt
str r7, [r1, r4]
str r7, [r1, #0x80] @ write load command
mov r8, #0x1000
onenand_wait_loop2:
subs r8, r8, #0x1
bne onenand_wait_loop2
onenand_wait_int: @ wait INT and RI
ldr r7, [r1, r4]
mov r8, #0x8000
orr r8, r8, #0x80
tst r7, r8
beq onenand_wait_int
mov r7, #0x0 @ clear interrupt
str r7, [r1, r4]
mov r8, #0xc00 @ source address (dataram1)
mov r10, #0x40 @ copy loop count (64 = 2048 / 32)
stmia sp, {r0-r7} @ backup
onenand_copy_to_ram:
ldmia r8!, {r0-r7}
stmia r9!, {r0-r7}
subs r10, r10, #0x1
bne onenand_copy_to_ram
ldmia sp, {r0-r7} @ restore
add r5, r5, #0x4 @ next FPA
cmp r5, #0x100 @ last FPA?
bne onenand_bl2_load
/* next block */
mov r5, #0x0 @ reset FPA
add r3, r3, #0x1 @ next FBA
cmp r3, #0x2 @ last FBA?
bne onenand_bl2_load
b after_copy
#endif
#ifdef CONFIG_BOOT_ONENAND_IROM
ldr sp, _TEXT_PHY_BASE
bl onenand_bl2_copy
b after_copy
#endif
//UBOOT代码拷贝结束后，就要考虑是否启动MMU了
after_copy:
#ifdef CONFIG_ENABLE_MMU
enable_mmu:
//使能MMU
/* enable domain access */
ldr r5, =0x0000ffff
mcr p15, 0, r5, c3, c0, 0 @ load domain access register
/* Set the TTB register */
ldr r0, _mmu_table_base
ldr r1, =CFG_PHY_UBOOT_BASE
ldr r2, =0xfff00000
bic r0, r0, r2
orr r1, r0, r1
mcr p15, 0, r1, c2, c0, 0
/* Enable the MMU */
mmu_on:
mrc p15, 0, r0, c1, c0, 0
orr r0, r0, #1 /* Set CR_M to enable MMU */
mcr p15, 0, r0, c1, c0, 0
nop
nop
nop
nop
#endif
skip_hw_init:
/* Set up the stack */
stack_setup:
#ifdef CONFIG_MEMORY_UPPER_CODE
ldr sp, =(CFG_UBOOT_BASE + CFG_UBOOT_SIZE - 0xc)
#else
ldr r0, _TEXT_BASE /* upper 128 KiB: relocated uboot */
sub r0, r0, #CFG_MALLOC_LEN /* malloc area 预留malloc空间 */
sub r0, r0, #CFG_GBL_DATA_SIZE /* bdinfo 预留bdinfo空间 */
#ifdef CONFIG_USE_IRQ
sub r0, r0, #(CONFIG_STACKSIZE_IRQ+CONFIG_STACKSIZE_FIQ) //预留IRQ和FIQ中断向量表空间
#endif
sub sp, r0, #12 /* leave 3 words for abort-stack 12个字节给中断栈 */
#endif
clear_bss: //清除bss段
ldr r0, _bss_start /* find start of bss segment */
ldr r1, _bss_end /* stop here */
mov r2, #0x00000000 /* clear */
clbss_l:
str r2, [r0] /* clear loop... */
add r0, r0, #4
cmp r0, r1
ble clbss_l
ldr pc, _start_armboot
_start_armboot:
.word start_armboot //开始第二阶段 跳转到SDRAM中运行
//根据CONFIG_ENABLE_MMU的配置情况，通过mmu_on使能MMU单元。接下来执行stack_setup初始化栈，调用clear_bss清除BSS段等，最终调用start_armboot，它位于lib_arm/board.c。
//此时执行的代码已经是复制到126M处的Uboot的代码，为什么？请看_mmu_table_base引用的mmu_table在board/samsung/smdk6410/lowlevel_init.S中的定义。
#ifdef CONFIG_ENABLE_MMU
_mmu_table_base:
.word mmu_table
#endif
/*
* copy U-Boot to SDRAM and jump to ram (from NAND or OneNAND)
* r0: size to be compared
* Load 1'st 2blocks to RAM because U-boot's size is larger than 1block(128k) size
* 一个重要的子程序是copy_from_nand，这将会把U-Boot镜像拷贝到内存中
*/
.globl copy_from_nand
copy_from_nand:
mov r10, lr /* save return address 保存返回地址*/
mov r9, r0 //r0值为0x1000 就是4096
/* get ready to call C functions sp是栈顶指针 fp是栈底指针*/
ldr sp, _TEXT_PHY_BASE /* setup temp stack pointer */
sub sp, sp, #12
mov fp, #0 /* no previous frame, so fp=0 */
mov r9, #0x1000
bl copy_uboot_to_ram // 位于 nand_cp.c it the first C functions
// r0存储copy_uboot_to_ram的返回值，即从FLASH向内存0x57e00000拷贝的字节数
3: tst r0, #0x0
bne copy_failed
ldr r0, =0x0c000000
ldr r1, _TEXT_PHY_BASE // 即CFG_PHY_UBOOT_BASE，也即0x57e00000 = MEMORY_BASE_ADDRESS + 0x7e00000 include/configs/smdk6410.h中定义
1: ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne compare_failed /* not matched */
subs r9, r9, #4
bne 1b
4: mov lr, r10 /* all is OK */
mov pc, lr //返回
copy_failed:
nop /* copy from nand failed */
b copy_failed
compare_failed:
nop /* compare failed */
b compare_failed
//如果存放在r0中的copy_uboot_to_ram的返回值不为0，则跳转到copy_failed。否则校验第一个4KB的代码是否和当前代码相同，如果不同跳转到compare_failed执行?
//否则跳转回bl copy_from_nand后的下一条指令继续执行。接下来执行after_copy子程序。
//验证前4K是因为，如果把UBOOT都拷贝过来应该是一样的。但不覆盖这段由硬件拷贝过来的4K内容，因为正在执行，无法打断。
/*
* we assume that cache operation is done before. (eg. cleanup_before_linux())
* actually, we don't need to do anything about cache if not use d-cache in U-Boot
* So, in this function we clean only MMU. by scsuh
*
* void theLastJump(void *kernel, int arch_num, uint boot_params);
*/
#ifdef CONFIG_ENABLE_MMU
.globl theLastJump
theLastJump:
mov r9, r0
ldr r3, =0xfff00000
ldr r4, _TEXT_PHY_BASE
adr r5, phy_last_jump
bic r5, r5, r3
orr r5, r5, r4
mov pc, r5
phy_last_jump:
/*
* disable MMU stuff
*/
mrc p15, 0, r0, c1, c0, 0
bic r0, r0, #0x00002300 /* clear bits 13, 9:8 (--V- --RS) */
bic r0, r0, #0x00000087 /* clear bits 7, 2:0 (B--- -CAM) */
orr r0, r0, #0x00000002 /* set bit 2 (A) Align */
orr r0, r0, #0x00001000 /* set bit 12 (I) I-Cache */
mcr p15, 0, r0, c1, c0, 0
mcr p15, 0, r0, c8, c7, 0 /* flush v4 TLB */
mov r0, #0
mov pc, r9
#endif
/*
*************************************************************************
*
* Interrupt handling
*
*************************************************************************
*/
@
@ IRQ stack frame.
@
#define S_FRAME_SIZE 72
#define S_OLD_R0 68
#define S_PSR 64
#define S_PC 60
#define S_LR 56
#define S_SP 52
#define S_IP 48
#define S_FP 44
#define S_R10 40
#define S_R9 36
#define S_R8 32
#define S_R7 28
#define S_R6 24
#define S_R5 20
#define S_R4 16
#define S_R3 12
#define S_R2 8
#define S_R1 4
#define S_R0 0
#define MODE_SVC 0x13
#define I_BIT 0x80
/*
* use bad_save_user_regs for abort/prefetch/undef/swi ...
* use irq_save_user_regs / irq_restore_user_regs for IRQ/FIQ handling
*/
.macro bad_save_user_regs
sub sp, sp, #S_FRAME_SIZE @ carve out a frame on current user stack
stmia sp, {r0 - r12} @ Save user registers (now in svc mode) r0-r12
ldr r2, _armboot_start
sub r2, r2, #(CFG_MALLOC_LEN)
sub r2, r2, #(CFG_GBL_DATA_SIZE+8) @ set base 2 words into abort stack
ldmia r2, {r2 - r3} @ get values for "aborted" pc and cpsr (into parm regs)
add r0, sp, #S_FRAME_SIZE @ grab pointer to old stack
add r5, sp, #S_SP
mov r1, lr
stmia r5, {r0 - r3} @ save sp_SVC, lr_SVC, pc, cpsr
mov r0, sp @ save current stack into r0 (param register)
.endm
.macro irq_save_user_regs
sub sp, sp, #S_FRAME_SIZE
stmia sp, {r0 - r12} @ Calling r0-r12
add r8, sp, #S_PC @ !!!! R8 NEEDS to be saved !!!! a reserved stack spot would be good.
stmdb r8, {sp, lr}^ @ Calling SP, LR
str lr, [r8, #0] @ Save calling PC
mrs r6, spsr
str r6, [r8, #4] @ Save CPSR
str r0, [r8, #8] @ Save OLD_R0
mov r0, sp
.endm
.macro irq_restore_user_regs
ldmia sp, {r0 - lr}^ @ Calling r0 - lr
mov r0, r0
ldr lr, [sp, #S_PC] @ Get PC
add sp, sp, #S_FRAME_SIZE
subs pc, lr, #4 @ return & move spsr_svc into cpsr
.endm
.macro get_bad_stack
ldr r13, _armboot_start @ setup our mode stack (enter in banked mode)
sub r13, r13, #(CFG_MALLOC_LEN) @ move past malloc pool
sub r13, r13, #(CFG_GBL_DATA_SIZE+8) @ move to reserved a couple spots for abort stack
str lr, [r13] @ save caller lr in position 0 of saved stack
mrs lr, spsr @ get the spsr
str lr, [r13, #4] @ save spsr in position 1 of saved stack
mov r13, #MODE_SVC @ prepare SVC-Mode
@ msr spsr_c, r13
msr spsr, r13 @ switch modes, make sure moves will execute
mov lr, pc @ capture return pc
movs pc, lr @ jump to next instruction & switch modes.
.endm
.macro get_bad_stack_swi
sub r13, r13, #4 @ space on current stack for scratch reg.
str r0, [r13] @ save R0's value.
ldr r0, _armboot_start @ get data regions start
sub r0, r0, #(CFG_MALLOC_LEN) @ move past malloc pool
sub r0, r0, #(CFG_GBL_DATA_SIZE+8) @ move past gbl and a couple spots for abort stack
str lr, [r0] @ save caller lr in position 0 of saved stack
mrs r0, spsr @ get the spsr
str lr, [r0, #4] @ save spsr in position 1 of saved stack
ldr r0, [r13] @ restore r0
add r13, r13, #4 @ pop stack entry
.endm
.macro get_irq_stack @ setup IRQ stack
ldr sp, IRQ_STACK_START
.endm
.macro get_fiq_stack @ setup FIQ stack
ldr sp, FIQ_STACK_START
.endm
/*
* exception handlers
*/
.align 5
undefined_instruction:
get_bad_stack
bad_save_user_regs
bl do_undefined_instruction
.align 5
software_interrupt:
get_bad_stack_swi
bad_save_user_regs
bl do_software_interrupt
.align 5
prefetch_abort:
get_bad_stack
bad_save_user_regs
bl do_prefetch_abort
.align 5
data_abort:
get_bad_stack
bad_save_user_regs
bl do_data_abort
.align 5
not_used:
get_bad_stack
bad_save_user_regs
bl do_not_used
#ifdef CONFIG_USE_IRQ
.align 5
irq:
get_irq_stack
irq_save_user_regs
bl do_irq
irq_restore_user_regs
.align 5
fiq:
get_fiq_stack
/* someone ought to write a more effiction fiq_save_user_regs */
irq_save_user_regs
bl do_fiq
irq_restore_user_regs
#else
.align 5
irq:
get_bad_stack
bad_save_user_regs
bl do_irq
.align 5
fiq:
get_bad_stack
bad_save_user_regs
bl do_fiq
#endif
.align 5
.global arm1136_cache_flush
arm1136_cache_flush:
mcr p15, 0, r1, c7, c5, 0 @ invalidate I cache
mov pc, lr @ back to caller
#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_CINTEGRATOR)
/* Use the IntegratorCP function from board/integratorcp/platform.S */
#elif defined(CONFIG_S3C64XX)
/* For future usage of S3C64XX*/
#else
.align 5
.globl reset_cpu
reset_cpu:
ldr r1, rstctl /* get addr for global reset reg */
mov r3, #0x2 /* full reset pll+mpu */
str r3, [r1] /* force reset */
mov r0, r0
_loop_forever:
b _loop_forever
rstctl:
.word PM_RSTCTRL_WKUP
#endif
1万+
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
