继上文《Ubuntu14.04安装配置Open vSwitch》安装好Open vSwitch后,这里我们将要创建两个KVM虚拟机,并通过DNSmasq来为这两个虚拟机自动分配私网IP地址。
虚拟机与宿主机网络结构图大致如下所示:
测试环境说明:
1)测试私网段:172.17.0.0/24
2)测试 vlan tag:100
下面简要介绍下整个配置流程:
1、安装dnsmasq:
◄► sudo apt-get install dnsmasq Reading package lists... Done Building dependency tree Reading state information... Done The following NEW packages will be installed: dnsmasq 0 upgraded, 1 newly installed, 0 to remove and 37 not upgraded. Need to get 14.9 kB of archives. After this operation, 114 kB of additional disk space will be used. Get:1 http://cn.archive.ubuntu.com/ubuntu/ trusty-updates/universe dnsmasq all 2.68-1ubuntu0.1 [14.9 kB] Fetched 14.9 kB in 0s (138 kB/s) Selecting previously unselected package dnsmasq. (Reading database ... 231198 files and directories currently installed.) Preparing to unpack .../dnsmasq_2.68-1ubuntu0.1_all.deb ... Unpacking dnsmasq (2.68-1ubuntu0.1) ... Processing triggers for ureadahead (0.100.0-16) ... ureadahead will be reprofiled on next reboot Setting up dnsmasq (2.68-1ubuntu0.1) ... * Starting DNS forwarder and DHCP server dnsmasq [ OK ] Processing triggers for ureadahead (0.100.0-16) ... ◄► sudo ps -ea | grep dns 3307 ? 00:00:00 dnsmasq
2、通过 ovs 创建一个 internal port,这里取名为 qdhcp,并设置 vlan id 为100,供下文的 dnsmasq 进程使用:
◄► sudo ovs-vsctl add-port br0 qdhcp tag=100 ◄► sudo ovs-vsctl set Interface qdhcp type=internal
3、查看已经创建的 qdhcp port:
◄► sudo ovs-vsctl show 1e6548a9-956e-4b86-b743-f8da0aa2b922 Bridge "br0" Port "br0" Interface "br0" type: internal Port qdhcp tag: 100 Interface qdhcp type: internal Port "eth0" Interface "eth0" ovs_version: "2.0.2" ◄► ifconfig qdhcp Link encap:Ethernet HWaddr 72:6c:a8:c2:48:68 inet6 addr: fe80::706c:a8ff:fec2:4868/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:578 (578.0 B)
4、给 qdhcp 虚拟网卡配置 IP 地址,这里IP地址必须为测试私网内的,这里我们就分配 172.17.0.1 给qdhcp:
◄► sudo ifconfig qdhcp 172.17.0.1 netmask 255.255.255.0 up ◄► ifconfig qdhcp Link encap:Ethernet HWaddr 72:6c:a8:c2:48:68 inet addr:172.17.0.1 Bcast:172.17.0.255 Mask:255.255.255.0 inet6 addr: fe80::706c:a8ff:fec2:4868/64 Scope:Link UP BROADCAST RUNNING MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:648 (648.0 B)
5、启动一个 dnsmasq 进程,监听 qdhcp 虚拟网卡:
◄► sudo /usr/sbin/dnsmasq --strict-order --bind-interfaces --interface=qdhcp --except-interface=lo --pid-file=/var/run/dnsmasq/qdhcp.pid --leasefile-ro --dhcp-range=172.17.0.2,172.17.0.254,255.255.255.0,12h --conf-file=
6、查看已经启动的 dnsmasq 进程:
◄► ps aux | grep dnsmasq nobody 3471 0.0 0.0 35228 2412 ? S 12:26 0:00 /usr/sbin/dnsmasq --strict-order --bind-interfaces --interface=qdhcp --except-interface=lo --pid-file=/var/run/dnsmasq/qdhcp.pid --leasefile-ro --dhcp-range=172.17.0.2,172.17.0.254,255.255.255.0,12h --conf-file=
7、下面就是整理两个虚拟机VM1、VM2的配置文件,这里仅展示 interface 这块配置项:
VM1:
<interface type='bridge'>
<source bridge='br0'/> <vlan> <tag id='100'/> </vlan> <virtualport type='openvswitch'/> <target dev='tap0'/> <model type='virtio'/> </interface> VM2: <interface type='bridge'> <source bridge='br0'/> <vlan> <tag id='100'/> </vlan> <virtualport type='openvswitch'/> <target dev='tap0'/> <model type='virtio'/> </interface>
这里将两个虚拟机的虚拟网卡的 vlan id 都设为 100,即必须保证和 qdhcp port在同一个vlan中。
8、启动VM1、VM2,并查看 ovs 虚拟网卡 tap0、tap1 的情况:
◄► sudo ovs-vsctl show 1e6548a9-956e-4b86-b743-f8da0aa2b922 Bridge "br0" Port "tap1" tag: 100 Interface "tap1" Port "br0" Interface "br0" type: internal Port qdhcp tag: 100 Interface qdhcp type: internal Port "eth0" Interface "eth0" Port "tap0" tag: 100 Interface "tap0" ovs_version: "2.0.2"
由此,我们已经将VM1、VM2和qdhcp port分在了同一个VLAN里了。
10、通过VNC登陆到VM1、VM2中,查看其是否获取到指定私网段IP地址:
VM1:
VM2:
11、从VM1 ping VM2:
至此,整合Open vSwitch与DNSmasq的功能就完成了,两个虚拟机之间就可以愉快地玩耍了。