linux+unknown+id,NetAPP + Linux iSCSI配置step-by-step

[root@dell2650 etc]# fdisk /dev/sdb

Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel

Building a new DOS disklabel. Changes will remain in memory only,

until you decide to write them. After that, of course, the previous

content won't be recoverable.

The number of cylinders for this disk is set to 20480.

There is nothing wrong with that, but this is larger than 1024,

and could in certain setups cause problems with:

1) software that runs at boot time (e.g., old versions of LILO)

2) booting and partitioning software from other OSs

(e.g., DOS FDISK, OS/2 FDISK)

Warning: invalid flag 0x0000 of partition table 4 will be corrected by w(rite)

Command (m for help): p

Disk /dev/sdb: 21.4 GB, 21474836480 bytes

64 heads, 32 sectors/track, 20480 cylinders

Units = cylinders of 2048 * 512 = 1048576 bytes

Device Boot Start End Blocks Id System

Command (m for help): n

Command action

e extended

p primary partition (1-4)

p

Partition number (1-4): 1

First cylinder (1-20480, default 1):

Using default value 1

Last cylinder or +size or +sizeM or +sizeK (1-20480, default 20480): +4096M

Command (m for help): p

Disk /dev/sdb: 21.4 GB, 21474836480 bytes

64 heads, 32 sectors/track, 20480 cylinders

Units = cylinders of 2048 * 512 = 1048576 bytes

Device Boot Start End Blocks Id System

/dev/sdb1 1 3907 4000752 83 Linux

Command (m for help): n

Command action

e extended

p primary partition (1-4)

p

Partition number (1-4): 2

First cylinder (3908-20480, default 3908):

Using default value 3908

Last cylinder or +size or +sizeM or +sizeK (3908-20480, default 20480):

Using default value 20480

Command (m for help): p

Disk /dev/sdb: 21.4 GB, 21474836480 bytes

64 heads, 32 sectors/track, 20480 cylinders

Units = cylinders of 2048 * 512 = 1048576 bytes

Device Boot Start End Blocks Id System

/dev/sdb1 1 3907 4000752 83 Linux

/dev/sdb2 3908 20480 16970752 83 Linux

Command (m for help): w

The partition table has been altered!

Calling ioctl() to re-read partition table.

Syncing disks.

[root@dell2650 etc]# cd /

[root@dell2650 /]# mkdir data1

[root@dell2650 /]# mkfs /dev/sdb1

mke2fs 1.32 (09-Nov-2002)

Filesystem label=

OS type: Linux

Block size=4096 (log=2)

Fragment size=4096 (log=2)

500960 inodes, 1000188 blocks

50009 blocks (5.00%) reserved for the super user

First data block=0

31 block groups

32768 blocks per group, 32768 fragments per group

16160 inodes per group

Superblock backups stored on blocks:

32768, 98304, 163840, 229376, 294912, 819200, 884736

Writing inode tables: done

Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 29 mounts or

180 days, whichever comes first. Use tune2fs -c or -i to override.

[root@dell2650 /]# mount /dev/sdb1 /data1

[root@dell2650 /]# df -k /data1

Filesystem 1K-blocks Used Available Use% Mounted on

/dev/sdb1 3937820 20 3737764 1% /data1

[root@dell2650 /]#