ok210linux内核配置,Tiny210v2( S5PV210 )平台下: 利用uboot启动远程Kernel(TFTP)以及挂载远程ROOTFS(NFS) Linux技术交流区 ARM9之家论坛...

最新推荐文章于 2023-06-01 11:08:19 发布

PixelYao

最新推荐文章于 2023-06-01 11:08:19 发布

阅读量177

点赞数

文章标签： ok210linux内核配置

root@Seagate:/tmp# minicom /dev/ttyS0

Welcome to minicom 2.5

OPTIONS: I18n

Compiled on May 2 2011, 00:39:27.

Port /dev/ttyS0

Press CTRL-A Z for help on special keys

OKOK

U-Boot 2013.01-rc2 (Jan 07 2013 - 10:18:16) for FriendlyLEG-TINY210

CPU: S5PC110@1000MHz

Board: FriendlyLEG-TINY210

DRAM: 512 MiB

WARNING: Caches not enabled

PWM Moudle Initialized.

GPD0CON : 1111, GPD0DAT : e

NAND: 2048 MiB

MMC: SAMSUNG SD/MMC: 0, SAMSUNG SD/MMC: 1

In: serial

Out: serial

Err: serial

Net: dm9000

Hit any key to stop autoboot: 0

dm9000 i/o: 0x88001000, id: 0x90000a46

DM9000: running in 16 bit mode

MAC: 00:40:5c:26:0a:5b

operating at 100M full duplex mode

Using dm9000 device

TFTP from server 192.168.1.5; our IP address is 192.168.1.80

Filename 'uImage'.

Load address: 0x21000000

Loading: #################################################################

#################################################################

#############################################

done

Bytes transferred = 3555936 (364260 hex)

## Booting kernel from Legacy Image at 21000000 ...

Image Name: Linux-3.0.8-TINY210V2+

Image Type: ARM Linux Kernel Image (uncompressed)

Data Size: 3555872 Bytes = 3.4 MiB

Load Address: 20008000

Entry Point: 20008000

Verifying Checksum ... OK

Loading Kernel Image ... OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

[ 0.000000] Initializing cgroup subsys cpu

[ 0.000000] Linux version 3.0.8-TINY210V2+ (zoulz@Seagate) (gcc version 4.7.3 20121205 (prerelease) (crosstool-NG hg+unknown-20130103.094521 - S5PV210) ) #5 PREEMPT Wed Jan 23 10:04:06 CST 2013

[ 0.000000] CPU: ARMv7 Processor [412fc082] revision 2 (ARMv7), cr=10c53c7f

[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache

[ 0.000000] Machine: MINI210

[ 0.000000] Memory policy: ECC disabled, Data cache writeback

[ 0.000000] CPU S5PV210/S5PC110 (id 0x43110220)

[ 0.000000] s5pv210_init_clocks: initializing clocks

[ 0.000000] s5pv210_setup_clocks: registering clocks

[ 0.000000] s5pv210_setup_clocks: clkdiv0 = 14131440, clkdiv1 = 00000400

[ 0.000000] s5pv210_setup_clocks: xtal is 24000000

[ 0.000000] S5PV210: PLL settings, A=1000000000, M=667000000, E=80000000 V=54000000

[ 0.000000] S5PV210: ARMCLK=1000000000, HCLKM=200000000, HCLKD=166750000

[ 0.000000] HCLKP=133400000, PCLKM=100000000, PCLKD=83375000, PCLKP=66700000

[ 0.000000] sclk_dmc: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_onenand: source is hclk_dsys (1), rate is 166750000

[ 0.000000] uclk1: source is mout_mpll (6), rate is 66700000

[ 0.000000] sclk_mixer: source is sclk_dac (0), rate is 54000000

[ 0.000000] sclk_fimc: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_cam0: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_cam1: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_fimd: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_mmc: source is mout_mpll (6), rate is 47642857

[ 0.000000] sclk_mmc: source is mout_epll (7), rate is 80000000

[ 0.000000] sclk_mfc: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_g2d: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_g3d: source is sclk_a2m (0), rate is 200000000

[ 0.000000] sclk_csis: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_spi: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_pwi: source is ext_xtal (0), rate is 24000000

[ 0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000

[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3dbf5000, 0-bank base(0x3dbf5000)

[ 0.000000] s5p: 36864 kbytes system memory reserved for mfc at 0x3b7f5000, 1-bank base(0x00000000)

[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc0 at 0x3b1f5000, 1-bank base(0x00000000)

[ 0.000000] s5p: 16 kbytes system memory reserved for fimc1 at 0x3b1f1000, 1-bank base(0x00000000)

[ 0.000000] s5p: 6144 kbytes system memory reserved for fimc2 at 0x3abf1000, 1-bank base(0x00000000)

[ 0.000000] s5p: 8192 kbytes system memory reserved for jpeg at 0x3a3f1000, 0-bank base(0x3a3f1000)

[ 0.000000] s5p: 13060 kbytes system memory reserved for fimd at 0x39730000, 1-bank base(0x00000000)

[ 0.000000] s5p: 8192 kbytes system memory reserved for g2d at 0x38f30000, 0-bank base(0x38f30000)

[ 0.000000] On node 0 totalpages: 102203

[ 0.000000] Normal zone: 1024 pages used for memmap

[ 0.000000] Normal zone: 0 pages reserved

[ 0.000000] Normal zone: 101179 pages, LIFO batch:31

[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768

[ 0.000000] pcpu-alloc: [0] 0

[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 101179

[ 0.000000] Kernel command line: root=/dev/nfs rw nfsroot=192.168.1.5:/opt/S5PV210/rootfs,nolock,tcp ip=192.168.1.80 console=ttySAC0,115200 ctp=1 kgdboc=ttySAC0,115200

[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)

[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

[ 0.000000] Memory: 399MB 0MB = 399MB total

[ 0.000000] Memory: 396940k/512416k available, 11872k reserved, 0K highmem

[ 0.000000] Virtual kernel memory layout:

[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)

[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)

[ 0.000000] DMA : 0xff000000 - 0xffe00000 ( 14 MB)

[ 0.000000] vmalloc : 0xe0800000 - 0xfd000000 ( 456 MB)

[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)

[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)

[ 0.000000] .init : 0xc0008000 - 0xc002d000 ( 148 kB)

[ 0.000000] .text : 0xc002d000 - 0xc06911ec (6545 kB)

[ 0.000000] .data : 0xc0692000 - 0xc06d9c40 ( 288 kB)

[ 0.000000] .bss : 0xc06d9c64 - 0xc071e000 ( 273 kB)

[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1

[ 0.000000] Preemptible hierarchical RCU implementation.

[ 0.000000] NR_IRQS:393

[ 0.000000] VIC @fd000000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd010000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd020000: id 0x00041192, vendor 0x41

[ 0.000000] VIC @fd030000: id 0x00041192, vendor 0x41

[ 0.000000] mult[140737]

[ 0.000000] max_delta_ns[2937815369]

[ 0.000000] min_delta_ns[30517]

[ 0.000000] rate[32768]

[ 0.000000] HZ[256]

[ 0.000000] Console: colour dummy device 80x30

[ 0.000000] console [ttySAC0] enabled

[ 0.491824] Calibrating delay loop... 994.84 BogoMIPS (lpj=1941504)

[ 0.515576] pid_max: default: 32768 minimum: 301

[ 0.515827] Mount-cache hash table entries: 512

[ 0.516312] Initializing cgroup subsys debug

[ 0.516362] Initializing cgroup subsys cpuacct

[ 0.516419] Initializing cgroup subsys freezer

[ 0.520295] CPU: Testing write buffer coherency: ok

[ 0.530660] print_constraints: dummy:

[ 0.530949] NET: Registered protocol family 16

[ 0.565355] fimd at 0x39730000

[ 0.565467] hsmmc0: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.565534] hsmmc1: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.565594] hsmmc2: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.565654] hsmmc3: sclk_mmc: source is mout_mpll, rate is 47642857

[ 0.573248] S5PV210: Initializing architecture

[ 0.577794] s3c-adc s5pv210-adc: attached adc driver

[ 0.581035] s3c24xx-pwm s3c24xx-pwm.0: tin at 66700000, tdiv at 66700000, tin=divclk, base 0

[ 0.590202] print_constraints: pd_tv_supply: 5000 mV normal

[ 0.595088] print_constraints: pd_lcd_supply: 5000 mV normal

[ 0.600797] print_constraints: pd_g3d_supply: 5000 mV normal

[ 0.606515] print_constraints: pd_mfc_supply: 5000 mV normal

[ 0.612256] print_constraints: pd_audio_supply: 5000 mV normal

[ 0.679867] bio: create slab at 0

[ 0.682650] SCSI subsystem initialized

[ 0.688076] usbcore: registered new interface driver usbfs

[ 0.688866] usbcore: registered new interface driver hub

[ 0.689384] usbcore: registered new device driver usb

[ 0.690919] s3c-i2c s3c2440-i2c.0: slave address 0x10

[ 0.690978] s3c-i2c s3c2440-i2c.0: bus frequency set to 378 KHz

[ 0.694312] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter

[ 0.698209] s3c-i2c s3c2440-i2c.1: slave address 0x10

[ 0.703096] s3c-i2c s3c2440-i2c.1: bus frequency set to 65 KHz

[ 0.709538] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter

[ 0.714317] s3c-i2c s3c2440-i2c.2: slave address 0x10

[ 0.719208] s3c-i2c s3c2440-i2c.2: bus frequency set to 260 KHz

[ 0.726196] s3c-i2c s3c2440-i2c.2: i2c-2: S3C I2C adapter

[ 0.732195] Advanced Linux Sound Architecture Driver Version 1.0.24.

[ 0.737949] Bluetooth: Core ver 2.16

[ 0.740770] NET: Registered protocol family 31

[ 0.744847] Bluetooth: HCI device and connection manager initialized

[ 0.751091] Bluetooth: HCI socket layer initialized

[ 0.755912] Bluetooth: L2CAP socket layer initialized

[ 0.760971] Bluetooth: SCO socket layer initialized

[ 0.766890] cfg80211: Calling CRDA to update world regulatory domain

[ 0.773644] Switching to clocksource clock_source_systimer

[ 0.781205] Switched to NOHz mode on CPU #0

[ 0.814450] NET: Registered protocol family 2

[ 0.814719] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

[ 0.815436] TCP established hash table entries: 16384 (order: 5, 131072 bytes)

[ 0.815751] TCP bind hash table entries: 16384 (order: 6, 327680 bytes)

[ 0.817762] TCP: Hash tables configured (established 16384 bind 16384)

[ 0.823843] TCP reno registered

[ 0.826926] UDP hash table entries: 256 (order: 1, 12288 bytes)

[ 0.832817] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)

[ 0.839450] NET: Registered protocol family 1

[ 0.843904] RPC: Registered named UNIX socket transport module.

[ 0.849390] RPC: Registered udp transport module.

[ 0.854022] RPC: Registered tcp transport module.

[ 0.858686] RPC: Registered tcp NFSv4.1 backchannel transport module.

[ 0.865330] PMU: registered new PMU device of type 0

[ 0.870717] cpuidle: phy_regs_save:0x389ff000

[ 0.874682] Loaded driver for PL330 DMAC-0 s3c-pl330

[ 0.879385] DBUFF-64x8bytes Num_Chans-8 Num_Peri-2 Num_Events-32

[ 0.885545] Loaded driver for PL330 DMAC-1 s3c-pl330

[ 0.890354] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[ 0.896527] Loaded driver for PL330 DMAC-2 s3c-pl330

[ 0.901343] DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32

[ 0.916582] ashmem: initialized

[ 0.949199] yaffs: yaffs built Jan 21 2013 17:12:49 Installing.

[ 0.949318] msgmni has been set to 775

[ 0.952233] io scheduler noop registered

[ 0.952280] io scheduler deadline registered

[ 0.952505] io scheduler cfq registered (default)

[ 0.953022] start plist test

[ 0.964738] end plist test

[ 0.965544] s3cfb s3cfb: win 2: pmem_start=0x39b95000

[ 0.965600] s3cfb s3cfb: [fb2] dma: 0x39b95000, cpu: 0xe1000000, size: 0x0085c000

[ 0.980388] FIMD src sclk = 166750000

[ 0.980503] s3cfb s3cfb: registered successfully

[ 0.999445] s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 16) is a S3C6400/10

[ 1.004497] s5pv210-uart.1: ttySAC1 at MMIO 0xe2900400 (irq = 20) is a S3C6400/10

[ 1.012278] s5pv210-uart.2: ttySAC2 at MMIO 0xe2900800 (irq = 24) is a S3C6400/10

[ 1.020063] s5pv210-uart.3: ttySAC3 at MMIO 0xe2900c00 (irq = 28) is a S3C6400/10

[ 1.028139] kgdb: Registered I/O driver kgdboc.

[ 1.029336] leds initialized

[ 1.029853] pwm initialized

[ 1.030397] mini210-adc initialized

[ 1.031294] backlight initialized

[ 1.033368] PA FB = 0x39B95000, bits per pixel = 32

[ 1.033419] screen width=800 height=480 va=0xd9b95000 pa=0x39b95000

[ 1.037300] xres_virtual = 800, yres_virtual = 1440, xoffset = 0, yoffset = 0

[ 1.044271] fb_size=8765440

[ 1.046967] Back frameBuffer[0].VAddr=d9d0c000 PAddr=39d0c000 size=1536000

[ 1.053883] Back frameBuffer[1].VAddr=d9e83000 PAddr=39e83000 size=1536000

[ 1.060711] Video Y Buffer[0].VAddr=d9ffa000 PAddr=39ffa000 size=921600

[ 1.067274] Video Y Buffer[1].VAddr=da0db000 PAddr=3a0db000 size=921600

[ 1.073853] Video Y Buffer[2].VAddr=da1bc000 PAddr=3a1bc000 size=921600

[ 1.080435] Video UV Buffer[0].VAddr=da29d000 PAddr=3a29d000 size=462848

[ 1.087114] Video UV Buffer[1].VAddr=da30e000 PAddr=3a30e000 size=462848

[ 1.093781] Video UV Buffer[2].VAddr=da37f000 PAddr=3a37f000 size=462848

[ 1.116968] brd: module loaded

[ 1.125950] loop: module loaded

[ 1.232765] MLC nand initialized, 2012 ported by FriendlyARM

[ 1.232829] S3C NAND Driver is using hardware ECC.

[ 1.232908] NAND device: Manufacturer ID: 0xec, Chip ID: 0xd5 (Samsung NAND 2GiB 3,3V 8-bit)

[ 1.232996] Creating 5 MTD partitions on "s5pv210-nand":

[ 1.234619] 0x0000000c0000-0x000000100000 : "misc"

[ 1.241942] 0x000000100000-0x000000600000 : "recovery"

[ 1.247967] 0x000000600000-0x000000b00000 : "kernel"

[ 1.252719] 0x000000b00000-0x000000e00000 : "ramdisk"

[ 1.257397] 0x000000e00000-0x000080000000 : "system"

[ 1.599156] PPP generic driver version 2.4.2

[ 1.600049] PPP Deflate Compression module registered

[ 1.600107] PPP BSD Compression module registered

[ 1.601243] PPP MPPE Compression module registered

[ 1.601298] NET: Registered protocol family 24

[ 1.601345] tun: Universal TUN/TAP device driver, 1.6

[ 1.611828] dm9000 Ethernet Driver, V1.31

[ 1.616853] eth0: dm9000a at e0838000,e083c00c IRQ 39 MAC: 00:40:5c:26:0a:5b (chip)

[ 1.623722] usbcore: registered new interface driver ath9k_htc

[ 1.629099] sdhci: Secure Digital Host Controller Interface driver

[ 1.634953] sdhci: Copyright(c) Pierre Ossman

[ 1.639317] s3c-sdhci s3c-sdhci.0: clock source 0: hsmmc (133400000 Hz)

[ 1.645807] s3c-sdhci s3c-sdhci.0: clock source 2: sclk_mmc (47642857 Hz)

[ 1.652605] mmc0: no vmmc regulator found

[ 1.656922] Registered led device: mmc0::

[ 1.661006] mmc0: SDHCI controller on samsung-hsmmc [s3c-sdhci.0] using ADMA

[ 1.667701] s3c-sdhci s3c-sdhci.1: clock source 0: hsmmc (133400000 Hz)

[ 1.674146] s3c-sdhci s3c-sdhci.1: clock source 2: sclk_mmc (47642857 Hz)

[ 1.682986] mmc1: no vmmc regulator found

[ 1.685346] Registered led device: mmc1::

[ 1.689318] mmc1: SDHCI controller on samsung-hsmmc [s3c-sdhci.1] using ADMA

[ 1.699252] s3c-sdhci s3c-sdhci.2: clock source 0: hsmmc (133400000 Hz)

[ 1.702486] s3c-sdhci s3c-sdhci.2: clock source 2: sclk_mmc (47642857 Hz)

[ 1.709288] mmc2: no vmmc regulator found

[ 1.715636] Registered led device: mmc2::

[ 1.717615] mmc2: SDHCI controller on samsung-hsmmc [s3c-sdhci.2] using ADMA

[ 1.724348] s3c-sdhci s3c-sdhci.3: clock source 0: hsmmc (133400000 Hz)

[ 1.730824] s3c-sdhci s3c-sdhci.3: clock source 2: sclk_mmc (47642857 Hz)

[ 1.740810] mmc3: no vmmc regulator found

[ 1.741967] Registered led device: mmc3::

[ 1.746035] mmc3: SDHCI controller on samsung-hsmmc [s3c-sdhci.3] using ADMA

[ 1.752951] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[ 1.761432] s5p-ehci s5p-ehci: S5P EHCI Host Controller

[ 1.764380] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1

[ 1.771406] s5p-ehci s5p-ehci: irq 87, io mem 0xec200000

[ 1.789533] s5p-ehci s5p-ehci: USB 0.0 started, EHCI 1.00

[ 1.790770] hub 1-0:1.0: USB hub found

[ 1.790847] hub 1-0:1.0: 1 port detected

[ 1.791927] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[ 1.798054] s5p-ohci s5p-ohci: EXYNOS OHCI Host Controller

[ 1.801174] s5p-ohci s5p-ohci: new USB bus registered, assigned bus number 2

[ 1.808229] s5p-ohci s5p-ohci: irq 87, io mem 0xec300000

[ 1.872876] hub 2-0:1.0: USB hub found

[ 1.872960] hub 2-0:1.0: 1 port detected

[ 1.874844] usbcore: registered new interface driver usbserial

[ 1.874907] usbserial: USB Serial Driver core

[ 1.874948] Initializing USB Mass Storage driver...

[ 1.878576] usbcore: registered new interface driver usb-storage

[ 1.879346] USB Mass Storage support registered.

[ 1.884530] s3c-udc : version 15 March 2009 (DMA Mode)

[ 1.906446] android_usb gadget: Mass Storage Function, version: 2009/09/11

[ 1.906517] android_usb gadget: Number of LUNs=1

[ 1.908906] lun0: LUN: removable file: (no medium)

[ 1.917974] android_usb gadget: android_usb ready

[ 1.935143] Registered gadget driver 'android_usb'

[ 1.936127] mousedev: PS/2 mouse device common for all mice

[ 1.937682] input: gpio-keys as /devices/platform/gpio-keys/input/input0

[ 1.939892] touchscreen-1wire initialized

[ 1.939941] backlight-1wire initialized

[ 1.943390] setup_irq: ret = 0

[ 1.949344] PWM clock = 66700000

[ 1.949382] TCNT_FOR_SAMPLE_BIT = 433, TCFG1 = 00010000

[ 1.955703] input: fa_ts_input as /devices/virtual/input/input1

[ 1.962284] ts-if initialized

[ 1.969103] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 1.976461] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 1.979792] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 1.985189] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 1.990673] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 2.000583] using rtc device, s3c, for alarms

[ 2.000695] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0

[ 2.007003] i2c /dev entries driver

[ 2.012407] Linux video capture interface: v2.00

[ 2.014907] gspca: v2.13.0 registered

[ 2.018650] usbcore: registered new interface driver zc3xx

[ 2.023610]

[ 2.037195] JPEG driver for S5PV210

[ 2.041789] i2c i2c-1: attached s5p_ddc into i2c adapter successfully

[ 2.060876] usbcore: registered new interface driver uvcvideo

[ 2.064060] USB Video Class driver (v1.1.0)

[ 2.110690] input: mma7660 as /devices/platform/s3c2440-i2c.0/i2c-0/0-004c/input/input2

[ 2.111368] mma7660 0-004c: MMA7660 device is probed successfully.

[ 2.111789] i2c-core: driver [mma7660] using legacy suspend method

[ 2.111853] i2c-core: driver [mma7660] using legacy resume method

[ 2.114800] MMA7660 sensor driver registered.

[ 2.125786] s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled

[ 2.134915] device-mapper: uevent: version 1.0.3

[ 2.138459] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com

[ 2.145779] Bluetooth: HCI UART driver ver 2.2

[ 2.150063] Bluetooth: HCI H4 protocol initialized

[ 2.154842] Bluetooth: HCI BCSP protocol initialized

[ 2.159764] Bluetooth: HCILL protocol initialized

[ 2.164444] Bluetooth: HCIATH3K protocol initialized

[ 2.169384] Bluetooth: Generic Bluetooth USB driver ver 0.6

[ 2.175389] usbcore: registered new interface driver btusb

[ 2.180717] cpuidle: using governor ladder

[ 2.185080] cpuidle: using governor menu

[ 2.208617] usbcore: registered new interface driver usbhid

[ 2.208677] usbhid: USB HID core driver

[ 2.211671] ALSA device list:

[ 2.211711] No soundcards found.

[ 2.211742] oprofile: hardware counters not available

[ 2.211784] oprofile: using timer interrupt.

[ 2.214112] TCP cubic registered

[ 2.216531] NET: Registered protocol family 17

[ 2.220996] NET: Registered protocol family 15

[ 2.225725] Bluetooth: RFCOMM TTY layer initialized

[ 2.230259] Bluetooth: RFCOMM socket layer initialized

[ 2.235331] Bluetooth: RFCOMM ver 1.11

[ 2.239059] Bluetooth: BNEP (Ethernet Emulation) ver 1.3

[ 2.244356] Bluetooth: BNEP filters: protocol multicast

[ 2.249546] Bluetooth: HIDP (Human Interface Emulation) ver 1.2

[ 2.255892] NET: Registered protocol family 35

[ 2.260125] lib80211: common routines for IEEE802.11 drivers

[ 2.265489] lib80211_crypt: registered algorithm 'NULL'

[ 2.270687] Registering the dns_resolver key type

[ 2.275418] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 2

[ 2.282994] ThumbEE CPU extension supported.

[ 2.287734] s5pv210_cpufreq_init: S5PV210 cpu-freq driver

[ 2.294262] regulator_init_complete: pd_mfc_supply: disabling

[ 2.298338] regulator_init_complete: pd_tv_supply: disabling

[ 2.304023] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

[ 2.309451] s3c-rtc s3c64xx-rtc: setting system clock to 2013-01-23 10:13:49 UTC (1358936029)

[ 2.323559] FIMC0 registered successfully

[ 2.325558] FIMC1 registered successfully

[ 2.327653] FIMC2 registered successfully

[ 2.336619] s5p-tvout s5p-tvout: hpd status is cable removed

[ 2.371581] usb 1-1: new high speed USB device number 2 using s5p-ehci

[ 2.383306] dm9000 dm9000: eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1

[ 2.398891] IP-Config: Guessing netmask 255.255.255.0

[ 2.399198] IP-Config: Complete:

[ 2.399239] device=eth0, addr=192.168.1.80, mask=255.255.255.0, gw=255.255.255.255,

[ 2.399315] host=192.168.1.80, domain=, nis-domain=(none),

[ 2.399365] bootserver=255.255.255.255, rootserver=192.168.1.5, rootpath=

[ 2.502828] hub 1-1:1.0: USB hub found

[ 2.503021] hub 1-1:1.0: 4 ports detected

[ 2.653901] VFS: Mounted root (nfs filesystem) on device 0:13.

[ 2.654047] Freeing init memory: 148K

[ 5.735512] s3c-rtc s3c64xx-rtc: rtc disabled, re-enabling

Please press Enter to activate this console.

[ 6.200469] udevd[876]: starting version 175

[root@FA-HF /]#

[ 12.817109] vo_open::check tvout start !!

[ 12.821308] vo_open::check tvout start !!

PixelYao

关注

0
点赞
踩
0

收藏

觉得还不错? 一键收藏
0
评论
ok210linux内核配置,Tiny210v2( S5PV210 )平台下: 利用uboot启动远程Kernel(TFTP)以及挂载远程ROOTFS(NFS) Linux技术交流区 ARM9之家论坛...

root@Seagate:/tmp# minicom/dev/ttyS0Welcome to minicom 2.5OPTIONS: I18nCompiled on May2 2011, 00:39:27.Port /dev/ttyS0Press CTRL-A Z for help on special keysOKOKU-Boot 2013.01-rc2 (Jan 07 2013 - 1...
复制链接

扫一扫