请一定要根据说明一步一步地操作

1、开机,按Ctrl+Break,在SP(Switch processor) Rommon中设置break/abort has effect
rommon 3 > confreg


    Configuration Summary
enabled are:
load rom after netboot fails
ignore system config info
console baud: 9600
boot: p_w_picpath specified by the boot system commands
      or default to: cisco2-Cat6k-Sup720/SP

do you wish to change the configuration? y/n  [n]:  y
enable  "diagnostic mode"? y/n  [n]:  
enable  "use net in IP bcast address"? y/n  [n]:  
disable "load rom after netboot fails"? y/n  [n]:  
enable  "use all zero broadcast"? y/n  [n]:  
enable  "break/abort has effect"? y/n  [n]:  y         //
disable "ignore system config info"? y/n  [n]:  y      //
change console baud rate? y/n  [n]:  
change the boot characteristics? y/n  [n]:  


系统提示reset，
重启，按照下面的第2步操作：

2、当SP切换到RP(router processor)时，按ctrl+break,进RP的ROMMON，修改confreg.
00:00:08: %OIR-SP-6-CONSOLE: Changing console ownership to route processor
（！！！！！！！！！注意：一定等到出现上面这一行在按Ctrl+Break进入ROMMON）


System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2004 by cisco Systems, Inc.
Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory

Download Start
*** Mistral Interrupt on line 4 ***
System memory 1 bit ECC correctable error interrupt ..
  PC = 0x800083fc, SP = 0x80007f00, RA = 0x80008488
  Cause Reg = 0x80004400, Status Reg = 0x3041c003




rommon 1 > confreg


           Configuration Summary
   (Virtual Configuration Register: 0x2102)
enabled are:
load rom after netboot fails
console baud: 9600
boot: p_w_picpath specified by the boot system commands
      or default to: cisco2-Cat6k-Sup720/RP

do you wish to change the configuration? y/n  [n]:  y
enable  "diagnostic mode"? y/n  [n]:  n
enable  "use net in IP bcast address"? y/n  [n]:  
disable "load rom after netboot fails"? y/n  [n]:  
enable  "use all zero broadcast"? y/n  [n]:  
enable  "break/abort has effect"? y/n  [n]:  y
enable  "ignore system config info"? y/n  [n]:  y
change console baud rate? y/n  [n]:  n
change the boot characteristics? y/n  [n]:  


           Configuration Summary
   (Virtual Configuration Register: 0x2042)
enabled are:
load rom after netboot fails
break/abort has effect
ignore system config info
console baud: 9600
boot: p_w_picpath specified by the boot system commands
      or default to: cisco2-Cat6k-Sup720/RP

do you wish to change the configuration? y/n  [n]:  n
rommon 2 > reset

System Bootstrap, Version 12.2(17r)S2, RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 2004 by cisco Systems, Inc.
Cat6k-Sup720/RP platform with 1048576 Kbytes of main memory

Download Start
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Download Completed! Booting the p_w_picpath.
Self decompressing the p_w_picpath : ############################################################################################################################################################## [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) s72033_rp Software (s72033_rp-PSV-M), Version 12.2(18)SXD7a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2006 by cisco Systems, Inc.
Compiled Tue 12-Sep-06 17:42 by tinhuang
Image text-base: 0x4002100C, data-base: 0x42040000

cisco CISCO7609 (R7000) processor (revision 1.0) with 983008K/65536K bytes of memory.
Processor board ID FOX074601H5
SR71000 CPU at 600Mhz, Implementation 0x504, Rev 1.2, 512KB L2 Cache
Last reset from s/w peripheral
X.25 software, Version 3.0.0.
Bridging software.
1 Virtual Ethernet/IEEE 802.3  interface(s)
48 FastEthernet/IEEE 802.3 interface(s)
10 Gigabit Ethernet/IEEE 802.3 interface(s)
1917K bytes of non-volatile configuration memory.
8192K bytes of packet buffer memory.

65536K bytes of Flash internal SIMM (Sector size 512K).

         --- System Configuration Dialog ---

Would you like to enter the initial configuration dialog? [yes/no]: n


Press RETURN to get started!