telnet  loopback接口
<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

 

首先telnet需要配置vty密码，然后配置特权模式密码
配置loopback接口后需要将其发布

 

下面是基本的端口配置与网络发布
Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R1
R1(config)#line con 0
R1(config-line)#logging syn
R1(config-line)#exec 0 0
R1(config-line)#exit
R1(config)#
R1(config)#
R1(config)#int s0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#no sh
%LINK-3-UPDOWN: Interface Serial0, changed state to up
R1(config-if)#
R1(config-if)#
R1(config-if)#int e0
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R1(config-if)#ip add 192.168.10.1 255.255.255.0
R1(config-if)#no sh
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
R1(config-if)#
R1(config-if)#int loopback 0
R1(config-if)#ip add <?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />10.1.1.1 255.255.255.0    此处要求后面的rip使用版本2
R1(config-if)#exit
R1(config)#
R1(config)#router rip

R1(config-router)#ver 2       rip v1 是不支持VLSM的

R1(config-router)#net 192.168.1.0

R1(config-router)#net 192.168.10.0

R1(config-router)#net 10.1.1.0

R1(config-router)#exit

 

接着配置密码
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#line vty 0 4

R1(config-line)#password 123

R1(config-line)#login

R1(config-line)#
R1(config-line)#exit
R1(config)#enable sec 123
R1(config)#exit

 

 

因为这个实验是在boson上作的，需要配置时钟频率
R1#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
R1(config)#int s0
R1(config-if)#clock rate 64000
R1(config-if)#exit

 

下面是rip发布结果
Router#sh ip rou
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
       i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, * - candidate default
       U - per-user static route

 

Gateway of last resort is not set

 

C    192.168.1.0 is directly connected, Serial0
C    192.168.20.0 is directly connected, Ethernet0
     10.0.0.0/24 is subnetted, 2 subnets
C       10.1.2.0 is directly connected, Loopback0
R       10.1.1.0 [120/1] via 192.168.1.1, 00:05:26, Serial0

R    192.168.10.0 [120/1] via 192.168.1.1, 00:04:40, Serial0

 

下面开始telnet结果

 

R1#telnet 10.1.2.1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Trying 10.1.2.1 ... Open