H3C MSTP、RSTP案例配置

1.MSTP配置

1.配置 VLAN 和端口
请按照图1-12在Device A和Device B上分别创建VLAN 10、20和30，在Device C上创建VLAN 10、
20 和 40，在Device D上创建VLAN 20、30 和 40；将各设备的各端口配置为Trunk端口并允许相应
的VLAN通过，具体配置：
DeviceA
sys
vlan 10
vlan 20
vlan 30
inter g 1/0/1
port link-type trunk
port trunk permit vlan 10 20
quit
inter g 1/0/2
port link-type trunk
port trunk permit vlan 20 30
quit
inter g 1/0/3
port link-type trunk
port trunk permit vlan all
quit

DeviceB
sys
vlan 10
vlan 20
vlan 30
inter g 1/0/1
port link-type trunk
port trunk permit vlan 20 30
quit
inter g 1/0/2
port link-type trunk
port trunk permit vlan 10 20
quit
inter g 1/0/3
port link-type trunk
port trunk permit vlan all
quit

DeviceC
sys
vlan 10
vlan 20
vlan 40
inter g 1/0/1
port link-type trunk
port trunk permit vlan 10 20
quit
inter g 1/0/2
port link-type trunk
port trunk permit vlan 10 20
quit
inter g 1/0/3
port link-type trunk
port trunk permit vlan 20 40
quit

DeviceD
sys
vlan 20
vlan 30
vlan 40
inter g 1/0/1
port link-type trunk
port trunk permit vlan 20 30
quit
inter g 1/0/2
port link-type trunk
port trunk permit vlan 20 30
quit
inter g 1/0/3
port link-type trunk
port trunk permit vlan 20 40
quit

2 配置 Device A
# 配置 MST 域的域名为 example，将 VLAN 10、30、40 
分别映射到 MSTI 1、3、4 上，并配置MSTP 的修订级别为 0。
<DeviceA> system-view
[DeviceA] stp region-configuration
[DeviceA-mst-region] region-name example
[DeviceA-mst-region] instance 1 vlan 10
[DeviceA-mst-region] instance 3 vlan 30
[DeviceA-mst-region] instance 4 vlan 40
[DeviceA-mst-region] revision-level 0
# 激活 MST 域的配置。
[DeviceA-mst-region] active region-configuration
[DeviceA-mst-region] quit
# 配置本设备为 MSTI 1 的根桥。
[DeviceA] stp instance 1 root primary
# 全局使能生成树协议。
[DeviceA] stp global enable

3 配置 Device B
# 配置 MST 域的域名为 example，将 VLAN 10、30、40 
分别映射到 MSTI 1、3、4 上，并配置MSTP 的修订级别为 0。
<DeviceB> system-view
[DeviceB] stp region-configuration
[DeviceB-mst-region] region-name example
[DeviceB-mst-region] instance 1 vlan 10
[DeviceB-mst-region] instance 3 vlan 30
[DeviceB-mst-region] instance 4 vlan 40
[DeviceB-mst-region] revision-level 0
# 激活 MST 域的配置。
[DeviceB-mst-region] active region-configuration
[DeviceB-mst-region] quit
# 配置本设备为 MSTI 3 的根桥。
[DeviceB] stp instance 3 root primary
# 全局使能生成树协议。
[DeviceB] stp global enable

4 配置 Device C
# 配置 MST 域的域名为 example，将 V