https://help.ubuntu.com/13.10/serverguide/network-configuration.html

Ethernet Interfaces

Ethernet interfaces are identified by the system using the naming convention of ethX, where X represents a numeric value. The first Ethernet interface is typically identified as eth0, the second as eth1, and all others should move up in numerical order.


Identify Ethernet Interfaces


To quickly identify all available Ethernet interfaces, you can use the ifconfig command as shown below.


ifconfig -a | grep eth

eth0      Link encap:Ethernet  HWaddr 00:15:c5:4a:16:5a

Another application that can help identify all network interfaces available to your system is the lshw command. In the example below, lshw shows a single Ethernet interface with the logical name of eth0 along with bus information, driver details and all supported capabilities.


sudo lshw -class network

 *-network

      description: Ethernet interface

      product: BCM4401-B0 100Base-TX

      vendor: Broadcom Corporation

      physical id: 0

      bus info: pci@0000:03:00.0

      logical name: eth0

      version: 02

      serial: 00:15:c5:4a:16:5a

      size: 10MB/s

      capacity: 100MB/s

      width: 32 bits

      clock: 33MHz

      capabilities: (snipped for brevity)

      configuration: (snipped for brevity)

      resources: irq:17 memory:ef9fe000-ef9fffff

Ethernet Interface Logical Names


Interface logical names are configured in the file /etc/udev/rules.d/70-persistent-net.rules. If you would like control which interface receives a particular logical name, find the line matching the interfaces physical MAC address and modify the value of NAME=ethX to the desired logical name. Reboot the system to commit your changes.


Ethernet Interface Settings


ethtool is a program that displays and changes Ethernet card settings such as auto-negotiation, port speed, duplex mode, and Wake-on-LAN. It is not installed by default, but is available for installation in the repositories.


sudo apt-get install ethtool

The following is an example of how to view supported features and configured settings of an Ethernet interface.


sudo ethtool eth0

Settings for eth0:

       Supported ports: [ TP ]

       Supported link modes:   10baseT/Half 10baseT/Full

                               100baseT/Half 100baseT/Full

                               1000baseT/Half 1000baseT/Full

       Supports auto-negotiation: Yes

       Advertised link modes:  10baseT/Half 10baseT/Full

                               100baseT/Half 100baseT/Full

                               1000baseT/Half 1000baseT/Full

       Advertised auto-negotiation: Yes

       Speed: 1000Mb/s

       Duplex: Full

       Port: Twisted Pair

       PHYAD: 1

       Transceiver: internal

       Auto-negotiation: on

       Supports Wake-on: g

       Wake-on: d

       Current message level: 0x000000ff (255)

       Link detected: yes

Changes made with the ethtool command are temporary and will be lost after a reboot. If you would like to retain settings, simply add the desired ethtool command to a pre-up statement in the interface configuration file /etc/network/interfaces.


The following is an example of how the interface identified as eth0 could be permanently configured with a port speed of 1000Mb/s running in full duplex mode.


auto eth0

iface eth0 inet static

pre-up /sbin/ethtool -s eth0 speed 1000 duplex full

Although the example above shows the interface configured to use the static method, it actually works with other methods as well, such as DHCP. The example is meant to demonstrate only proper placement of the pre-up statement in relation to the rest of the interface configuration.


IP Addressing

The following section describes the process of configuring your systems IP address and default gateway needed for communicating on a local area network and the Internet.


Temporary IP Address Assignment


For temporary network configurations, you can use standard commands such as ip, ifconfig and route, which are also found on most other GNU/Linux operating systems. These commands allow you to configure settings which take effect immediately, however they are not persistent and will be lost after a reboot.


To temporarily configure an IP address, you can use the ifconfig command in the following manner. Just modify the IP address and subnet mask to match your network requirements.


sudo ifconfig eth0 10.0.0.100 netmask 255.255.255.0

To verify the IP address configuration of eth0, you can use the ifconfig command in the following manner.


ifconfig eth0

eth0      Link encap:Ethernet  HWaddr 00:15:c5:4a:16:5a  

         inet addr:10.0.0.100  Bcast:10.0.0.255  Mask:255.255.255.0

         inet6 addr: fe80::215:c5ff:fe4a:165a/64 Scope:Link

         UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

         RX packets:466475604 errors:0 dropped:0 overruns:0 frame:0

         TX packets:403172654 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:1000

         RX bytes:2574778386 (2.5 GB)  TX bytes:1618367329 (1.6 GB)

         Interrupt:16

To configure a default gateway, you can use the route command in the following manner. Modify the default gateway address to match your network requirements.


sudo route add default gw 10.0.0.1 eth0

To verify your default gateway configuration, you can use the route command in the following manner.


route -n

Kernel IP routing table

Destination     Gateway         Genmask         Flags Metric Ref    Use Iface

10.0.0.0        0.0.0.0         255.255.255.0   U     1      0        0 eth0

0.0.0.0         10.0.0.1        0.0.0.0         UG    0      0        0 eth0

If you require DNS for your temporary network configuration, you can add DNS server IP addresses in the file /etc/resolv.conf. In general, editing /etc/resolv.conf directly is not recommanded, but this is a temporary and non-persistent configuration. The example below shows how to enter two DNS servers to /etc/resolv.conf, which should be changed to servers appropriate for your network. A more lengthy description of the proper persistent way to do DNS client configuration is in a following section.


nameserver 8.8.8.8

nameserver 8.8.4.4

If you no longer need this configuration and wish to purge all IP configuration from an interface, you can use the ip command with the flush option as shown below.


ip addr flush eth0

Flushing the IP configuration using the ip command does not clear the contents of /etc/resolv.conf. You must remove or modify those entries manually, or re-boot which should also cause /etc/resolv.conf, which is actually now a symlink to /run/resolvconf/resolv.conf, to be re-written.


Dynamic IP Address Assignment (DHCP Client)


To configure your server to use DHCP for dynamic address assignment, add the dhcp method to the inet address family statement for the appropriate interface in the file /etc/network/interfaces. The example below assumes you are configuring your first Ethernet interface identified as eth0.


auto eth0

iface eth0 inet dhcp

By adding an interface configuration as shown above, you can manually enable the interface through the ifup command which initiates the DHCP process via dhclient.


sudo ifup eth0

To manually disable theinterface, you can use the ifdown command, which in turn will initiate the DHCP release process and shut down the interface.


sudo ifdown eth0

Static IP Address Assignment


To configure your system to use a static IP address assignment, add the static method to the inet address family statement for the appropriate interface in the file /etc/network/interfaces. The example below assumes you are configuring your first Ethernet interface identified as eth0. Change the address, netmask, and gateway values to meet the requirements of your network.


auto eth0

iface eth0 inet static

address 10.0.0.100

netmask 255.255.255.0

gateway 10.0.0.1

By adding an interface configuration as shown above, you can manually enable the interface through the ifup command.


sudo ifup eth0

To manually disable theinterface, you can use the ifdown command.


sudo ifdown eth0

Loopback Interface


The loopback interface is identified by the system as lo and has a default IP address of 127.0.0.1. It can be viewed using the ifconfig command.


ifconfig lo

lo        Link encap:Local Loopback  

         inet addr:127.0.0.1  Mask:255.0.0.0

         inet6 addr: ::1/128 Scope:Host

         UP LOOPBACK RUNNING  MTU:16436  Metric:1

         RX packets:2718 errors:0 dropped:0 overruns:0 frame:0

         TX packets:2718 errors:0 dropped:0 overruns:0 carrier:0

         collisions:0 txqueuelen:0

         RX bytes:183308 (183.3 KB)  TX bytes:183308 (183.3 KB)

By default, there should be two lines in /etc/network/interfaces responsible for automatically configuring your loopback interface. It is recommended that you keep the default settings unless you have a specific purpose for changing them. An example of the two default lines are shown below.


auto lo

iface lo inet loopback

Name Resolution

Name resolution as it relates to IP networking is the process of mapping IP addresses to hostnames, making it easier to identify resources on a network. The following section will explain how to properly configure your system for name resolution using DNS and static hostname records.


DNS Client Configuration


Traditionally, the file /etc/resolv.conf was a static configuration file that rarely needed to be changed or automatically changed via DCHP client hooks. Nowadays, a computer can switch from one network to another quite often and the resolvconf framework is now being used to track these changes and update the resolver's configuration automatically. It acts as an intermediary between programs that supply nameserver information and applications that need nameserver information. Resolvconf gets populated with information by a set of hook scripts related to network interface configuration. The most notable difference for the user is that any change manually done to /etc/resolv.conf will be lost as it gets overwritten each time something triggers resolvconf. Instead, resolvconf uses DHCP client hooks, and /etc/network/interfaces to generate a list of nameservers and domains to put in /etc/resolv.conf, which is now a symlink:


/etc/resolv.conf -> ../run/resolvconf/resolv.conf

To configure the resolver, add the IP addresses of the nameservers that are appropriate for your network in the file /etc/network/interfaces. You can also add an optional DNS suffix search-lists to match your network domain names. For each other valid resolv.conf configuration option, you can include, in the stanza, one line beginning with that option name with a dns- prefix. The resulting file might look like the following:

iface eth0 inet static

   address 192.168.3.3

   netmask 255.255.255.0

   gateway 192.168.3.1

   dns-search example.com

   dns-nameservers 192.168.3.45 192.168.8.10

The search option can also be used with multiple domain names so that DNS queries will be appended in the order in which they are entered. For example, your network may have multiple sub-domains to search; a parent domain of example.com, and two sub-domains, sales.example.com and dev.example.com.


If you have multiple domains you wish to search, your configuration might look like the following:


iface eth0 inet static

   address 192.168.3.3

   netmask 255.255.255.0

   gateway 192.168.3.1

   dns-search example.com sales.example.com dev.example.com

   dns-nameservers 192.168.3.45 192.168.8.10

If you try to ping a host with the name of server1, your system will automatically query DNS for its Fully Qualified Domain Name (FQDN) in the following order:


server1.example.com


server1.sales.example.com


server1.dev.example.com


If no matches are found, the DNS server will provide a result of notfound and the DNS query will fail.


Static Hostnames


Static hostnames are locally defined hostname-to-IP mappings located in the file /etc/hosts. Entries in the hosts file will have precedence over DNS by default. This means that if your system tries to resolve a hostname and it matches an entry in /etc/hosts, it will not attempt to look up the record in DNS. In some configurations, especially when Internet access is not required, servers that communicate with a limited number of resources can be conveniently set to use static hostnames instead of DNS.


The following is an example of a hosts file where a number of local servers have been identified by simple hostnames, aliases and their equivalent Fully Qualified Domain Names (FQDN's).


127.0.0.1localhost

127.0.1.1ubuntu-server

10.0.0.11server1 server1.example.com ***

10.0.0.12server2 server2.example.com mail

10.0.0.13server3 server3.example.com www

10.0.0.14server4 server4.example.com file

In the above example, notice that each of the servers have been given aliases in addition to their proper names and FQDN's. Server1 has been mapped to the name ***, server2 is referred to as mail, server3 as www, and server4 as file.


Name Service Switch Configuration


The order in which your system selects a method of resolving hostnames to IP addresses is controlled by the Name Service Switch (NSS) configuration file /etc/nsswitch.conf. As mentioned in the previous section, typically static hostnames defined in the systems /etc/hosts file have precedence over names resolved from DNS. The following is an example of the line responsible for this order of hostname lookups in the file /etc/nsswitch.conf.


hosts:          files mdns4_minimal [NOTFOUND=return] dns mdns4

files first tries to resolve static hostnames located in /etc/hosts.


mdns4_minimal attempts to resolve the name using Multicast DNS.


[NOTFOUND=return] means that any response of notfound by the preceding mdns4_minimal process should be treated as authoritative and that the system should not try to continue hunting for an answer.


dns represents a legacy unicast DNS query.


mdns4 represents a Multicast DNS query.


To modify the order of the above mentioned name resolution methods, you can simply change the hosts: string to the value of your choosing. For example, if you prefer to use legacy Unicast DNS versus Multicast DNS, you can change the string in /etc/nsswitch.conf as shown below.


hosts:          files dns [NOTFOUND=return] mdns4_minimal mdns4

Bridging

Bridging multiple interfaces is a more advanced configuration, but is very useful in multiple scenarios. One scenario is setting up a bridge with multiple network interfaces, then using a firewall to filter traffic between two network segments. Another scenario is using bridge on a system with one interface to allow virtual machines direct access to the outside network. The following example covers the latter scenario.


Before configuring a bridge you will need to install the bridge-utils package. To install the package, in a terminal enter:


sudo apt-get install bridge-utils

Next, configure the bridge by editing /etc/network/interfaces:


auto lo

iface lo inet loopback


auto br0

iface br0 inet static

       address 192.168.0.10

       network 192.168.0.0

       netmask 255.255.255.0

       broadcast 192.168.0.255

       gateway 192.168.0.1

       bridge_ports eth0

       bridge_fd 9

       bridge_hello 2

       bridge_maxage 12

       bridge_stp off

为你的物理接口和网络输入相应的值。


Now restart networking to enable the bridge interface:


sudo service networking restart

The new bridge interface should now be up and running. The brctl provides useful information about the state of the bridge, controls which interfaces are part of the bridge, etc. See man brctl for more information.