1、FIFO QUEUE
2、WFQ QUEUE
3、PRIORITY QUEUE
4、CUSTOM QUEUE
5、CLASS　BASED　WEIGHTED　FAIR　QUEUE
6.   Low latency queuing（LLQ）
7.  CLASS　BASED   Low latency queuing
默认情况下<=E1的线路默认启用的就是WFQ，E1=2.048M,大于E1默认就是FIFO。
 
分类：WFO加权队列，是基于flow的形式默认分类的，不需要人工干预。默认的是WFO丢弃不是尾丢弃，我们要明白两个概念 class and flow class 手工定义classification  making像PQ CQ, 而flow基于sou ip  des ip tcp/udp port transport protocol TOS.默认是256个flow。
明白这两个概念：congestive discard threshold (CDT)
                                  Hold-Queue Out limit (HQL)
加队：early droping when the congestive discard thresold (CDT)is reached
aggressive droping when the hold-queue out limit (HQO)is reached
也就是说有个一个数据包进入缓存经过flow进入也一个队列，包的个数大于CDT，如果这个队列已满，直接drop，没有满insert，包的个数大于HQL，队列已满 drop 不是最长队列的包，会aggerssive drop 最长队列的那个包，这个数据包insert
调度：finish time=real packet size/(ip precedent+1) FT最小的先发送
看个例子：

A1 的FT=50 A2=60 B1=100 B2=150
所以顺序是 A1  A2  B1  B2
其实making优先级是没有作用，关键我们要看action 在低速链路上我们默认的队列机制是WFQ 所以语音的ip pre5 有高的优先级，看以先走
 
R2#show int s1/0
Serial1/0 is up, line protocol is up
  Hardware is M4T
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, crc 16, loopback not set
  Keepalive set (10 sec)
  Restart-Delay is 0 secs
  Last input 00:00:50, output 00:00:02, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair       默认的WFQ
  Output queue: 0/1000/64/0 (size/max total/threshold/drops) 64 CDT  HQL 1000 
     Conversations  0/1/256 (active/max active/max total)   总共flow的个数
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 1158 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     1 packets input, 332 bytes, 0 no buffer
     Received 1 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     3 packets output, 646 bytes, 0 underruns
     0 output errors, 0 collisions, 1 interface resets
     0 output buffer failures, 0 output buffers swapped out
     2 carrier transitions     DCD=up  DSR=up  DTR=up  RTS=up  CTS=up
 
R2(config-if)#fair-queue 128 1024  37 （CDT  动态Q   RSVP ）
                                      64   256   0  (默认)
R2(config-if)#hold-queue 2000 out    HQO
R2#show queueing fair
Current fair queue configuration:
  Interface           Discard    Dynamic  Reserved  Link    Priority
                      threshold  queues   queues    queues  queues
  Serial1/0           128        1024     37        8       1   
  Serial1/1           64         256      0         8       1   
  Serial1/2           64         256      0         8       1   
  Serial1/3           64         256      0         8       1  
PQ:介绍
priority queueing 默认有四个优先级，默认的是尾丢弃，高优先级的先出去，等优先级高的队列发出去完了在发送下面的队列，这个不足容易造成低优先级的队列饿死！
Router(config)#priority-list 2 ?
  default      Set priority queue for unspecified datagrams
  interface    Establish priorities for packets from a named interface  基于接口（入口）
  protocol     priority queueing by protocol                    基于协议
  queue-limit  Set queue limits for priority queues   限制优先级队列的大小
1\HIGH
2\MEDIUM
3\NORMAL
4\LOW
access-list 110 permit gre any any
access-list 110 permit ip any host 192.168.1.100
priority-list 1 protocol ip high list 110
priority-list 1 protocol ip medium tcp smtp
priority-list 1 protocol ip normal udp ntp
priority-list 1 protocol ip low tcp www
priority-list 1 queue-limit 40 20 20 20    （ 20 40 60 80默认)
）
interface Serial1/0
  priority-group 1
Router#show queueing priority
Current DLCI priority queue configuration:
Current priority queue configuration:
List   Queue  Args
1      high   protocol ip          list 110
1      medium protocol ip          tcp port smtp
1      normal protocol ip          udp port ntp
1      low    protocol ip          tcp port www
1      high   limit 40
1      medium limit 20
1      normal limit 20
1      low    limit 20
Router#show int s1/0
Serial1/0 is up, line protocol is up 
  
 Queueing strategy: priority-list 1
  Output queue (queue priority: size/max/drops):
     high: 0/40/0, medium: 0/20/0, normal: 0/20/0, low: 0/20/0
CQ 介绍：尾丢弃 调度轮询调度 17个class
R2(config)#queue-list 1 ?
  default        Set custom queue for unspecified datagrams
  interface      Establish priorities for packets from a named interface   基于接口
  lowest-custom  Set lowest number of queue to be treated as custom  默认0是先执行 我们在这可以设置
  protocol       priority queueing by protocol                                    基于协议
  queue          Configure parameters for a particular queue     对queue配置响应的参数
   stun           Establish priorities for stun packets 

 
access-list 110 permit gre any any
access-list 110 permit ip any any precedence critical
queue-list 1 interface Ethernet0/0 2
queue-list 1 protocol ip 3 tcp www
queue-list 1 protocol ip 3 list 110
queue-list 1 queue 2 limit 3000
queue-list 1 queue 3 limit 3000
 
interface Serial1/0
 no ip address
 serial restart-delay 0
 custom-queue-list 1
R2#show queueing custom
Current custom queue configuration:
List   Queue  Args
1      2      interface Ethernet0/0        
1      3      protocol ip          tcp port www
1      3      protocol ip          list 110
1      2      limit 3000
1      3      limit 3000

R2(config)#queue-list 1 lowest-custom 2   队列0 1 是优先级最高的相当于PQ+CQ
LLQ 介绍 ：对语音流量设置优先 相当于PQ+WFQ
在WFQ的基础之上设置
 
this is used for links with speed less than 1.544Mbps(T1)
R1(config)#int s1/0
R1(config-if)#ip rtp
R1(config-if)#ip rtp pr
R1(config-if)#ip rtp priority ?
  <2000-65535>  Lower bound of UDP destination port
R1(config-if)#ip rtp priority 16384 16383  ？

R1(config-if)#ip rtp priority 16384 16383 ?
  <0-2000>  Maximum allowed bandwidth in kbps
R1(config-if)#ip rtp priority 16384 16383 100(为语音预留的带宽)
 
CLASS　BASED　WEIGHTED　FAIR　QUEUE介绍：
 
 64+1（default）  手工分类+制定带宽    尾丢弃   轮询转发
bandwidth 
bandwidth percent  总带宽的百分比
bandwidth remaining percent  实际可用的带宽百分比（总带宽的百分比*0.75*Y%）
bandwith（av）=bandwith（total）*0.75—MWrtp
 
class-map match-all VTOP  
 match ip rtp 16384 16383
用NBAR抓的流量 用NBAR抓流量是比较简单的，可以根据特定的协议去抓
我们还可以用ACL抓流量
（access-list 110 permit ip any any precedence 5
class-map match-all VTOP
match access-group 110）
class-map match-all WWW
 match protocol http

policy-map CBWFQ
 class VTOP
  bandwidth percent 50
 class WWW
  bandwidth percent 20
 class class-default
  bandwidth percent 30
interface Serial1/0
 R2(config-if)#max-reserved-bandwidth 100
no ip address
 serial restart-delay 0
 max-reserved-bandwidth 100
 service-policy output CBWFQ
 hold-queue 2000 out
我们还可以在默认的定义为WFQ
 
class class-default
fair-queue
LLQ
 
low-latency queueing 低延迟队列 相当于WFQ+PQ 首先接口队列要是WFQ
R1(config)#int s1/0
R1(config-if)#ip rtp
R1(config-if)#ip rtp pr
R1(config-if)#ip rtp priority ?
  <2000-65535>  Lower bound of UDP destination port
R1(config-if)#ip rtp priority 16384 16383  ？

R1(config-if)#ip rtp priority 16384 16383 ?
  <0-2000>  Maximum allowed bandwidth in kbps
R1(config-if)#ip rtp priority 16384 16383 100(为语音预留的带宽)
max-reserved-bandwith percent(%)
实际带宽=全部带宽*75%-带宽RTP（为语音预留的带宽）
 
CBLLQ 可以设置PQ让其优先 有PQ你就先走
 
policy-map CBWFQ
class VTOP
 priority  percent 50  强制优先