cisco无线控制器的初始化配置

System will nowrestart!

 

Bootloader 4.0.217.0(Apr 12 2007 - 17:46:14)

 

Motorola PowerPCProcessorID=00000000 Rev. PVR=80200020

        CPU: 833 MHz

        CCB: 333 MHz

        DDR: 166 MHz

        LBC: 41 MHz

L1 D-cache 32KB, L1I-cache 32KB enabled.

I2C:  ready

DTT:   1 is 33 C

DRAM:  DDR module detected, total size:512MB.

512 MB

8540 inPCI Host Mode.

8540 is the PCIArbiter.

 

Memory Test PASS

 

FLASH:

  Flash Bank 0: portsize = 2, size = 8 MB in142 Sectors

 8 MB

L2 cache enabled:256KB

Card Id: 1540

Card Revision Id: 1

Card CPU Id: 1287

Number of MACAddresses: 32

Number of SlotsSupported: 4

Serial Number: FOC1127F04H

Unknown command Id:0xa5

Unknown command Id:0xa4

Unknown command Id:0xa3

Manufacturers ID:30464

Board MaintenanceLevel: 00

Number of supportedAPs: 50

In:    serial

Out:   serial

Err:   serial

 

 

 

 

 

                      .o88b. d888888b.d8888.  .o88b.  .d88b.

                     d8P  Y8  `88'   88'  YP d8P Y8 .8P  Y8.

                     8P         88   `8bo.   8P      88   88

                     8b         88     `Y8b. 8b      88    88

                     Y8b  d8  .88.   db   8D Y8b d8 `8b  d8'

                      `Y88P' Y888888P`8888Y'  `Y88P'  `Y88P'

                    ModelAIR-WLC4402-50-K9   S/N: FOC1127F04H

Net:  

 PHY DEVICE : Found Intel LXT971APHY at 0x01

FEC ETHERNET

IDE:   Bus 0: OK

  Device 0: Model: STI Flash 7.4.0Firm: 01.25.06 Ser#: STI

J11B407102084630

            Type: Removable Hard Disk

            Capacity: 245.0 MB = 0.2 GB (501760x 512)

  Device 1: not available

 

Booting PrimaryImage...

Press <ESC> nowfor additional boot options...

 

***** External ConsoleActive *****

 

    Boot Options

 

Please choose anoption from below:

 

 1. Run primary image (version 4.1.185.0)(active)

 2. Run backup image (version 4.0.217.0)

 3. Manually update images

 4. Change active boot image

 5. Clear Configuration

 

Please enter yourchoice: 5          清除原有的配置

 

Detecting Hardware . ..

 

 

 

Re-buildingconfiguration filesystem

Done.

 

Bootloader 4.0.217.0(Apr 12 2007 - 17:46:14)

 

Motorola PowerPCProcessorID=00000000 Rev. PVR=80200020

        CPU: 833 MHz

        CCB: 333 MHz

        DDR: 166 MHz

        LBC: 41 MHz

L1 D-cache 32KB, L1I-cache 32KB enabled.

I2C:  ready

DTT:   1 is 33 C

DRAM:  DDR module detected, total size:512MB.

512 MB

8540 inPCI Host Mode.

8540 is the PCIArbiter.

 

Memory Test PASS

 

FLASH:

  Flash Bank 0: portsize = 2, size = 8 MB in 142Sectors

 8 MB

L2 cache enabled:256KB

Card Id: 1540

Card Revision Id: 1

Card CPU Id: 1287

Number of MACAddresses: 32

Number of SlotsSupported: 4

Serial Number: FOC1127F04H

Unknown command Id:0xa5

Unknown command Id:0xa4

Unknown command Id:0xa3

Manufacturers ID:30464

Board MaintenanceLevel: 00

Number of supportedAPs: 50

In:    serial

Out:   serial

Err:   serial

 

 

 

 

 

                      .o88b. d888888b.d8888.  .o88b.  .d88b.

                     d8P  Y8  `88'   88'  YP d8P Y8 .8P  Y8.

                     8P         88   `8bo.   8P      88   88

                     8b         88     `Y8b. 8b      88    88

                     Y8b  d8  .88.   db   8D Y8b d8 `8b  d8'

                      `Y88P' Y888888P`8888Y'  `Y88P'  `Y88P'

                    Model AIR-WLC4402-50-K9   S/N: FOC1127F04H

Net:  

 PHY DEVICE : Found Intel LXT971APHY at 0x01

FEC ETHERNET

IDE:   Bus 0: OK

  Device 0: Model: STI Flash 7.4.0Firm: 01.25.06 Ser#: STI

J11B407102084630

            Type: Removable Hard Disk

            Capacity: 245.0 MB = 0.2 GB (501760 x512)

  Device 1: not available

 

Booting PrimaryImage...

Press <ESC> nowfor additional boot options...

Detecting Hardware . ..

 

 

Generating SecureShell DSA Host Key ...

Generating SecureShell RSA Host Key ...

Generating SecureShell version 1.5 RSA Host Key ...

Cisco is a trademarkof Cisco Systems, Inc.

Software CopyrightCisco Systems, Inc. All rights reserved.

 

Cisco AireOS Version4.1.185.0

Initializing OSServices: ok

Initializing SerialServices: ok

Initializing InternalInterfaces: ok

Initializing NetworkServices: ok

Starting ARP Services:ok

Starting Trap Manager:ok

Starting NetworkInterface Management Services: ok

Starting SystemServices: ok

Starting Fast PathHardware Acceleration: ok

Starting SwitchingServices: ok

Starting QoS Services:ok

Starting FIPSFeatures: Not enabled

Starting PolicyManager: ok

Starting DataTransport Link Layer: ok

Starting AccessControl List Services: ok

Starting SystemInterfaces: ok

Starting ClientTroubleshooting Service: ok

Starting ManagementFrame Protection: ok

Starting LWAPP: ok

Starting CryptoAccelerator[s]: None Present

Starting CertificateDatabase: ok

Starting VPN Services:ok

Starting SecurityServices: ok

Starting PolicyManager: ok

Starting AuthenticationEngine: ok

Starting MobilityManagement: ok

Starting Virtual APServices: ok

Starting AireWaveDirector: ok

Starting Network TimeServices: ok

Starting CiscoDiscovery Protocol: ok

Starting BroadcastServices: ok

Starting LoggingServices: ok

Starting DHCP Server:ok

Starting IDS SignatureManager: ok

Starting RFID TagTracking: ok

Starting Power Supplyand Fan Status Monitoring Service: ok

Starting TSM: ok

Starting LOCP: ok

Starting CIDSServices: ok

StartingEthernet-over-IP: ok

Starting ManagementServices:

   Web Server: ok

   CLI: ok

   Secure Web: Web Authentication Certificatenot found (error).

 

(Cisco Controller)

 

 

Welcome to the CiscoWizard Configuration Tool

Use the '-' characterto backup

System Name[Cisco_68:9b:e3]: Cisco_WLC_Master                   设置无线控制器的系统命名

Enter AdministrativeUser Name (24 characters max): admin             设置无线控制器的管理员

Enter AdministrativePassword (24 characters max): *****                设置无线控制器的管理员密码

Re-enterAdministrative Password                 :*****              确认设置无线控制器管理员密码

 

Service Interface IPAddress Configuration [none][DHCP]: none          是否开启web管理口的DHCP服务 <带外管理 OOB>

Service Interface IPAddress: 192.168.0.1                            设置web管理口的管理地址

Service InterfaceNetmask: 255.255.255.0                            设置web管理口的管理地址的掩码

 

Enable LinkAggregation (LAG) [yes][NO]: NO                          是否开启链路汇聚功能《开启只要mode on就够了》

 

Management InterfaceIP Address: 10.38.2.2                          设置无线控制器的管理地址 《inband管理》

Management InterfaceNetmask: 255.255.255.0                        设置无线控制器的管理地址的掩码

Management InterfaceDefault Router: 10.38.2.31                       设置无线控制器的管理端口的默认网关

Management InterfaceVLAN Identifier (0 = untagged): 2                 设置无线网络所属的VLAN

Management InterfacePort Num [1 to 2]: 1                             设置管理端口为端口1或端口2

Management InterfaceDHCP Server IP Address: 10.38.2.31              设置DHCP服务器地址

 

AP Transport Mode[layer2][LAYER3]: LAYER3                          设置传输模式为3层传输

AP Manager InterfaceIP Address: 10.38.2.3                             设置AP的管理接口地址

 

AP-Manager is onManagement subnet, using same values

AP Manager InterfaceDHCP Server (10.67.32.1):                        设置AP的管理接口的DHCP服务器地址

 

Virtual Gateway IPAddress: 1.1.1.1                                    设置虚拟的网关地址

 

Mobility/RF GroupName: GROUP1                                    设置所属的分组

 

Enable SymmetricMobility Tunneling [yes][NO]: YES                     是否启用移动传输功能

 

Network Name (SSID): CIMC                                          设置无线网络的SSID

Allow Static IPAddresses [YES][no]: YES                               是否接受静态IP地址

 

Configure a RADIUSServer now? [YES][no]: no                          是否马上设置RADIUS服务

Warning! The defaultWLAN security policy requires a RADIUS server.

Please seedocumentation for more details.

 

Enter Country Codelist (enter 'help' for a list of countries) [US]: CN         输入所属的地区

 

Enable 802.11b Network[YES][no]: YES                                是否启用802.11b的网络

Enable 802.11a Network [YES][no]: YES                                是否启用802.11a的网络

Enable 802.11g Network [YES][no]: YES                                是否启用802.11g的网络

Enable Auto-RF[YES][no]: YES                                        是否启用自动射频

 

Configuration saved!

Resetting system withnew configuration...

 

 

Configuration saved!

Resetting system withnew configuration...

 

 

Bootloader 4.0.217.0(Apr 12 2007 - 17:46:14)

 

Motorola PowerPCProcessorID=00000000 Rev. PVR=80200020

        CPU: 833 MHz

        CCB: 333 MHz

        DDR: 166 MHz

        LBC: 41 MHz

L1 D-cache 32KB, L1I-cache 32KB enabled.

I2C:  ready

DTT:   1 is 34 C

DRAM:  DDR module detected, total size:512MB.

512 MB

8540 inPCI Host Mode.

8540 is the PCIArbiter.

 

Memory Test PASS

 

FLASH:

  Flash Bank 0: portsize = 2, size = 8 MB in142 Sectors

 8 MB

L2 cache enabled:256KB

Card Id: 1540

Card Revision Id: 1

Card CPU Id: 1287

Number of MACAddresses: 32

Number of SlotsSupported: 4

Serial Number: FOC1127F04H

Unknown command Id:0xa5

Unknown command Id:0xa4

Unknown command Id:0xa3

Manufacturers ID:30464

Board MaintenanceLevel: 00

Number of supportedAPs: 50

In:    serial

Out:   serial

Err:   serial

 

 

 

 

 

                      .o88b. d888888b.d8888.  .o88b.  .d88b.

                     d8P  Y8  `88'   88'  YP d8P Y8 .8P  Y8.

                     8P         88   `8bo.   8P      88   88

                     8b         88     `Y8b. 8b      88    88

                     Y8b  d8  .88.   db   8D Y8b d8 `8b  d8'

                      `Y88P' Y888888P`8888Y'  `Y88P'  `Y88P'

                    ModelAIR-WLC4402-50-K9   S/N: FOC1127F04H

Net:  

 PHY DEVICE : Found Intel LXT971APHY at 0x01

FEC ETHERNET

IDE:   Bus 0: OK

  Device 0: Model: STI Flash 7.4.0Firm: 01.25.06 Ser#: STI

J11B407102084630

            Type: Removable Hard Disk

            Capacity: 245.0 MB = 0.2 GB (501760x 512)

  Device 1: not available

 

Booting PrimaryImage...

Press <ESC> nowfor additional boot options...

Detecting Hardware . ..

 

 

Cisco is a trademarkof Cisco Systems, Inc.

Software CopyrightCisco Systems, Inc. All rights reserved.

 

Cisco AireOS Version4.1.185.0

Initializing OSServices: ok

Initializing SerialServices: ok

Initializing InternalInterfaces: ok

Initializing NetworkServices: ok

Starting ARP Services:ok

Starting Trap Manager:ok

Starting NetworkInterface Management Services: ok

Starting SystemServices: ok

Starting Fast PathHardware Acceleration: ok

Starting SwitchingServices: ok

Starting QoS Services:ok

Starting FIPSFeatures: Not enabled

Starting PolicyManager: ok

Starting DataTransport Link Layer: ok

Starting AccessControl List Services: ok

Starting SystemInterfaces: ok

Starting ClientTroubleshooting Service: ok

Starting ManagementFrame Protection: ok

Starting LWAPP: ok

Starting CryptoAccelerator[s]: None Present

Starting CertificateDatabase: ok

Starting VPN Services:ok

Starting SecurityServices: ok

Starting PolicyManager: ok

StartingAuthentication Engine: ok

Starting MobilityManagement: ok

Starting Virtual APServices: ok

Starting AireWaveDirector: ok

Starting Network TimeServices: ok

Starting CiscoDiscovery Protocol: ok

Starting BroadcastServices: ok

Starting LoggingServices: ok

Starting DHCP Server:ok

Starting IDS SignatureManager: ok

Starting RFID TagTracking: ok

Starting Power Supplyand Fan Status Monitoring Service: ok

Starting TSM: ok

Starting LOCP: ok

Starting CIDS Services:ok

StartingEthernet-over-IP: ok

Starting ManagementServices:

   Web Server: ok

   CLI: ok

   Secure Web: ok

 

(Cisco Controller)

 

Enter User Name (or'Recover-Config' this one-time only to reset

configuration tofactory defaults)

 

User:  admin

Password:*****

(Cisco Controller)>

(Cisco Controller)>

(Cisco Controller)>

(Cisco Controller)>show tech-support                                    查看无线控制器当前状态

 

 

---------------Showboot---------------

 

Primary BootImage............................... Code 4.1.185.0 (active)

Backup BootImage................................ Code 4.0.217.0

 

---------------showtime---------------

 

 

Time.............................................Sun Oct 21 10:40:41

2007

 

 

---------------ShowInventory---------------

 

System Inventory

Burned-in MACAddress............................ 00:1B:D5:68:9B:E0

Crypto Accelerator1............................. Absent

Crypto Accelerator2............................. Absent

Power Supply1................................... Absent

Power Supply2................................... Present, OK

 

---------------Showudi---------------

 

NAME:"Chassis"    , DESCR:"Chassis"

PID: AIR-WLC4402-50-K9,  VID: V02, SN: FOC1127F04H

 

---------------Showsysinfo---------------

 

System Information

Manufacturer'sName.............................. Cisco Systems Inc.

ProductName..................................... Cisco Controller

Product Version..................................4.1.185.0

RTOSVersion..................................... 4.1.185.0

BootloaderVersion............................... 4.0.217.0

BuildType....................................... DATA + WPS

 

SystemName...................................... Cisco_WLC_Secondary

SystemLocation..................................

SystemContact...................................

SystemObjectID..................................

1.3.6.1.4.1.14179.1.1.4.3

IPAddress....................................... 10.67.32.6

System UpTime................................... 0 days 0 hrs 1 mins 7

secs

 

ConfiguredCountry............................... CN - China

OperatingEnvironment............................ Commercial (0 to 40 C)

Internal Temp AlarmLimits....................... 0 to 65 C

--More-- or (q)uit

InternalTemperature............................. +34 C

 

State of 802.11bNetwork......................... Enabled

State of 802.11aNetwork......................... Enabled

Number of WLANs..................................1

3rd Party Access PointSupport................... Disabled

Number of ActiveClients......................... 0

 

Burned-in MACAddress............................ 00:1B:D5:68:9B:E0

Crypto Accelerator1............................. Absent

Crypto Accelerator2............................. Absent

Power Supply1................................... Absent

Power Supply2................................... Present, OK

 

---------------ShowInterface ---------------

 

Interface Configuration

InterfaceName................................... ap-manager

MACAddress...................................... 00:1b:d5:68:9b:e3

IPAddress....................................... 10.67.32.5

IPNetmask....................................... 255.255.255.0

IPGateway....................................... 10.67.32.1

VLAN.............................................100      

--More-- or (q)uit

Active PhysicalPort............................. 1        

Primary PhysicalPort............................ 1        

Backup PhysicalPort............................. Unconfigured

Primary DHCPServer.............................. 10.67.32.1

Secondary DHCPServer............................ Unconfigured

DHCP Option82................................... Disabled

ACL..............................................Unconfigured

APManager....................................... Yes

 

InterfaceName................................... management

MACAddress...................................... 00:1b:d5:68:9b:e0

IP Address.......................................10.67.32.6

IPNetmask....................................... 255.255.255.0

IPGateway....................................... 10.67.32.1

VLAN.............................................100      

Active PhysicalPort............................. 1        

Primary PhysicalPort............................ 1        

Backup PhysicalPort............................. Unconfigured

Primary DHCPServer.............................. 10.67.32.1

Secondary DHCPServer............................ Unconfigured

DHCP Option82................................... Disabled

ACL..............................................Unconfigured

APManager....................................... No

--More-- or (q)uit

 

InterfaceName................................... service-port

MACAddress...................................... 00:1b:d5:68:9b:e1

IPAddress....................................... 192.168.0.1

IPNetmask....................................... 255.255.255.0

DHCP Option 82...................................Disabled

DHCPProtocol.................................... Disabled

APManager....................................... No

 

InterfaceName................................... virtual

MACAddress...................................... 00:1b:d5:68:9b:e0

IPAddress....................................... 1.1.1.1

DHCP Option82................................... Disabled

Virtual DNS HostName............................ Disabled

APManager....................................... No

 

 

---------------Showport summary---------------

 

Port Summary

           STP  Admin   Physical   Physical  Link   Link    Mcast     

Pr  Type  Stat   Mode     Mode     Status   Status  Trap  Appliance  

POE 

-- ------- ----------- ---------- ---------- ------ ------- --------- -

------

--More-- or (q)uit

1  Normal Forw Enable  Auto       1000 Full  Up    Enable  Enable    

N/A    

2  Normal Disa Enable  Auto       Auto       Down  Enable  Enable    

N/A    

 

---------------Showprocess cpu---------------

 

 Name               Priority     CPU Use  Reaper

 

 reaperWatcher      ( 3/ 96)        0     ( 0/  0)%   I

 osapiReaper        ( 10/ 94)        0    (  0/  0)%   I

 TempStatus         (240/ 7)        0     ( 0/  0)%   I

 emWeb              (240/  7)       0     (  0/ 0)%   T 300

 UtilTask           (240/  7)       0     (  0/ 0)%   T 300

 webJavaTask        (240/ 7)        0     ( 0/  0)%  

 ethoipOsapiMsgRcv  (240/ 7)        0     (  0/  0)%  

 ethoipSocketTask   (240/ 7)        0     ( 0/  0)%  

 cids-cl Task       (240/ 7)        0     ( 0/  0)%  

 locpTxServerTask

 bcastReceiveTask   (240/ 7)        0     ( 0/  0)%  

 CDP Main           (240/  7)       0     (  0/ 0)%  

 sntpMainTask       (

 mmSSHPeerRegister  (240/ 7)        0     ( 0/  0)%  

 mmListen           (180/ 30)        0    (  0/  0)%  

 aaaQueueReader     (225/ 13)       

 gccp_t             (240/  7)       0     (  0/ 0)%  

 dot1dTimer         (240/ 7)        0     ( 0/  0)%   T 300

 dot1dRecv     

 osapiTimer         (100/ 60)        0    (  0/  0)%   T300

 nim_t              (100/ 60)        0    (  0/  0)%  

 dtlDataLowTask     (240/ 7)  

 tsmTask            (255/  1)              0            0     (  0/  0)%

 

 PowerSupplyStatus  (240/ 7)              0            0   

 apfRLDP            (175/ 32)            312            1      ( 0/  0)%

 

 apfRLDPRecv        (175/ 32)              0            0      ( 0/  0)%

 

 mfpTrapForwardTask (255/  1)              0            0      ( 0/  0)%

 

 mfpEventTask       (255/ 1)              0            0      ( 0/  0)%

 

 DHCP Proxy Task    (240/ 7)              0            0      ( 0/  0)%

 

 DHCP Client Task   (240/  7)             0            0      ( 0/  0)%

  T 600

 BootP 

   Buffers InUse................................ 6

 

Web Server Resources

   DescriptorsAllocated......................... 31

   Descriptors Used...

    chunks in use:     6460

    bytes in use:      413440

Pool[02]: 128 bytechunks

    chunks in pool:    4400

    chunks in use:     4302

    bytes in use:

Raw Pool:

    chunks in use:     89

    bytes requested:   61356651

 

---------------Showmemory statistics---------------

 

 

System Memory S

 

 

---------------Showmsglog---------------

 

Message Log SeverityLevel ...................... CRITICAL

Oct 21 10:04:26.217hwutils.c:2159 INIT-0-MSGTAG007: Security Module not found.

Oct 21 10:04:25.446bootos.c:874 INIT-0-MSGTAG001: Starting code...

                                                                                                                   

(Cisco Controller)>config network webmode enable                        启用web界面模式功能

(Cisco Controller)>config network mgmt-via-wireless enable                启用无线管理功能

(Cisco Controller)>config network telnet enable                            启用telnet功能

本文转自 bilinyee博客，原文链接：    http://blog.51cto.com/ericfu/1789993      如需转载请自行联系原作者