TOP图如上图
 
 
R1的配置：
Press Enter to Start
<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

 

 

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R1
R1(config)#int e0
R1(config-if)#ip add 192.168.1.1 255.255.255.0
R1(config-if)#ip nat inside
R1(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
R1(config-if)#int s0
R1(config-if)#ip add 192.168.2.5 255.255.255.252
R1(config-if)#ip nat outside
R1(config-if)#clock rate 1000000
R1(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
R1(config-if)#encapsulation hdlc
R1(config-if)#exit
R1(config)#access-list 1 permit 192.168.1.0 <?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />0.0.0.255 //设置允许访问的内部IP地址列表

R1(config)#ip nat pool ssss 202.101.1.1 202.101.2.10 netmask 255.255.255.0 //配置全局IP地址池ssss

R1(config)#ip nat inside source list 1 pool ssss overload //蓝色部分和静态的NAT是一样的，只是内部地址改为list 1,而内部全局地址孜为了pool ssss

R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 192.168.1.0
R1(config-router)#network 192.168.2.4
R1(config-router)#end
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up

 

R2的配置：

 

 

Press Enter to Start

 

 

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host R2
R2(config)#int e0
R2(config-if)#ip add 202.101.6.1 255.255.255.0
R2(config-if)#no shut
%LINK-3-UPDOWN: Interface Ethernet0, changed state to up
R2(config-if)#int s0
R2(config-if)#ip add 192.168.2.6 255.255.255.252
R2(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
R2(config-if)#exit
R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#network 192.168.2.4
R2(config-router)#network 202.101.6.0
R2(config-router)#end
R2#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
//配置R2的telnet
R2(config)#line vty 0 4

R2(config-line)#login

R2(config-line)#password cisco

R2(config-line)#end

 

在R1和R2上查看NAT信息：
1、R1#sh ip nat translations
Pro  Inside global     Inside local      Outside local      Outside global
icmp202.101.1.1:9392      192.168.1.2:9392      202.101.6.1:9392       202.101.6.1:9392
icmp202.101.1.1:9393      192.168.1.2:9393      202.101.6.1:9393       202.101.6.1:9393
icmp202.101.1.1:9394      192.168.1.2:9394      202.101.6.1:9394       202.101.6.1:9394
icmp202.101.1.1:9395      192.168.1.2:9395      202.101.6.1:9395       202.101.6.1:9395
icmp202.101.1.1:9396      192.168.1.2:9396      202.101.6.1:9396       202.101.6.1:9396

 

 

icmp202.101.1.1:9392      192.168.1.2:9392      202.101.6.2:9392       202.101.6.2:9392
icmp202.101.1.1:9393      192.168.1.2:9393      202.101.6.2:9393       202.101.6.2:9393
icmp202.101.1.1:9394      192.168.1.2:9394      202.101.6.2:9394       202.101.6.2:9394
icmp202.101.1.1:9395      192.168.1.2:9395      202.101.6.2:9395       202.101.6.2:9395
icmp202.101.1.1:9396      192.168.1.2:9396      202.101.6.2:9396       202.101.6.2:9396

 

 

icmp202.101.1.1:9392      192.168.1.3:9392      202.101.6.1:9392       202.101.6.1:9392
icmp202.101.1.1:9393      192.168.1.3:9393      202.101.6.1:9393       202.101.6.1:9393
icmp202.101.1.1:9394      192.168.1.3:9394      202.101.6.1:9394       202.101.6.1:9394
icmp202.101.1.1:9395      192.168.1.3:9395      202.101.6.1:9395       202.101.6.1:9395
icmp202.101.1.1:9396      192.168.1.3:9396      202.101.6.1:9396       202.101.6.1:9396
2、用host 1 telnet到R2，然后查看users:
   telnet 202.101.6.1
   show users