备份 cisco ISO
开启本地的 X:\tftpserver\Cisco TFTP Server\Cisco TFTP Server.exe,当然这个交换机是可以连接的。
以下是实例解析:
internet-east-10#dir
Directory of flash:/
3 -rwx 3736 Jun 27 1993 09:42:24 +00:00 config.text
4 -rwx 11536 Jul 13 1993 04:35:23 +00:00 vlan.dat
5 drwx 192 Mar 1 1993 00:18:36 +00:00 c3750-ipservices-mz.122-25.SEB4
363 -rwx 27 Jun 27 1993 09:42:24 +00:00 private-config.text
15998976 bytes total (7977472 bytes free)
internet-east-10#dir c3750-ipservices-mz.122-25.SEB4
Directory of flash:/c3750-ipservices-mz.122-25.SEB4/
6 -rwx 6405766 Mar 1 1993 00:17:37 +00:00 c3750-ipservices-mz.122-25.SEB4.bin
7 drwx 4032 Mar 1 1993 00:18:05 +00:00 html
362 -rwx 596 Mar 1 1993 00:18:36 +00:00 info
15998976 bytes total (7977472 bytes free)
internet-east-10#copy flash tftp
Source filename [/c3750-ipservices-mz.122-25.SEB4/c3750-ipservices-mz.122-25.SEB4.bin]?
Address or name of remote host []? 192.168.7.98
Destination filename [c3750-ipservices-mz.122-25.SEB4.bin]?
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
6405766 bytes copied in 63.561 secs (100781 bytes/sec)
internet-east-10#
备份、上传Cisco ISO文件
一、 配置设备的管理地址
conf t
interface vlan 1
ip add IP地址 掩码 // 这个地址作为远程管理设备的地址
exit
ip default-gateway IP地址 // 全局模式下,这个是网关地址
二、备份现有设备的IOS和配置 (前提条件是你的pc上必须有tftpserver)
dir // 查看当前设备里面的ISO文件
copy flash tftp // 备份设备上的ISO
Source filename [ ]? eg: 大厦东10层 c3750-ipservices-mz.122-25.SEB4/c3750-ipservices-mz.122-25.SEB4.bin // 输入想要备份的文件名称,一般这个备份的都是一个后缀是bin的文件
Address or name of remote host [ ]? // 这个输入的是安装有tftpserver机器的IP地址
Destination filename // 这是有点类似另存为中的更改文件名,就是文件存储在tftpserver上的名称一般保持默认
三、 删除设备上现有的IOS
由于考虑到设备的硬件flash大小,所以要把现有的IOS删除掉(也可以更改名称),以便新的IOS顺利上传到flash上来
delete xxx.bin // 删除设备的ISO文件
dir // 查看,确认一下
四、上传新的IOS到flash
把新的IOS放在TFTP server的root目录下
copy tftp flash //上传新的IOS
Address or name of remote host [ ]? // 输入tftpserver的IP地址
Source filename [ ]? // 输入tftpserver根目录下的ISO文件名
Destination filename [c3550-smi.bin]? // 保持和tftpserver根目录下的ISO文件名相同就行
五、更改设备启动引导文件
更改设备的系统引导文件,以便设备正常从新的IOS启动
show boot // 查看设备当前的启动文件
boot system flash:xxx.bin // xxx.bin是刚才上穿的文件,这个是在全局模式下
write // 保存当前的配置,在#模式
转载于:https://blog.51cto.com/wenchylinux/380982