路由器的配置如下：
rta:<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

      
Press Enter to Start

 

 

Router>
Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host rta
rta(config)#int s0  //hdlc的配置
rta(config-if)#clock rate 64000
rta(config-if)#ip add <?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />1.1.1.1 255.255.255.252
rta(config-if)#encapsulation hdlc
rta(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINK-3-UPDOWN: Interface Serial0, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to down
%LINK-3-UPDOWN: Interface Serial0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0, changed state to up
rta(config-if)#end
rta#ping 1.1.1.2

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
rta#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
rta(config)#int s1  //无认证的配置
rta(config-if)#ip add 1.1.1.5 255.255.255.252
rta(config-if)#clock rate 148000
rta(config-if)#encapsulation ppp
rta(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINK-3-UPDOWN: Interface Serial1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
rta(config-if)#end
rta#ping 1.1.1.6

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.6, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
rta#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
rta(config)#username rtd password 123
rta(config)#int s2  //ppp with chap认证的配置
rta(config-if)#ip add 1.1.1.9 255.255.255.252
rta(config-if)#clock rate 64000
rta(config-if)#encapsulation ppp
rta(config-if)#ppp authentication chap
rta(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial2, changed state to up
%LINK-3-UPDOWN: Interface Serial2, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2, changed state to down
%LINK-3-UPDOWN: Interface Serial2, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial2, changed state to up
rta(config-if)#end
rta#ping 1.1.1.10

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

 

 

rtb:

 

 

Press Enter to Start

 

 

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host rtb
rtb(config)#int s0
rtb(config-if)#ip add 1.1.1.2 255.255.255.252
rtb(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
rtb(config-if)#end
rtb#ping 1.1.1.1

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

 

 

rtc:

 

Press Enter to Start

 

 

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host rtc
rtc(config)#username rtd password cisco
rtc(config)#int s1   ///ppp with pap认证的配置
rtc(config-if)#ip add 1.1.1.13 255.255.255.252
rtc(config-if)#clock rate 148000
rtc(config-if)#encapsulation ppp
rtc(config-if)#ppp authentication pap
rtc(config-if)#ppp pap sent-username rtc password cisco
rtc(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINK-3-UPDOWN: Interface Serial1, changed state to down
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to down
%LINK-3-UPDOWN: Interface Serial1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up
rtc(config-if)#end
rtc#ping 1.1.1.14

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.14, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
rtc#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
rtc(config)#int s0
rtc(config-if)#ip add 1.1.1.6 255.255.255.252
rtc(config-if)#encapsulation ppp
rtc(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
rtc(config-if)#end
rtc#ping 1.1.1.5

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.5, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms

 

rtd:

 

Press Enter to Start

 

 

Router>en
Router#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
Router(config)#host rtd
rtd(config)#username rtc password cisco
rtd(config)#int s0
rtd(config-if)#ip add 1.1.1.14 255.255.255.252
rtd(config-if)#encapsulation ppp
rtd(config-if)#ppp authentication pap
rtd(config-if)#ppp pap sent-username rtd password cisco
rtd(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial0, changed state to up
rtd(config-if)#
rtd(config-if)#end
rtd#ping 1.1.1.13

 

Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.13, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms
rtd#
rtd#conf t
Enter configuration commands, one per line.  End with CNTL/Z.
rtd(config)#username rta password 123
rtd(config)#int s1
rtd(config-if)#ip add 1.1.1.10 255.255.255.252
rtd(config-if)#encapsulation ppp
rtd(config-if)#ppp authentication chap
rtd(config-if)#no shut
%LINK-3-UPDOWN: Interface Serial1, changed state to up
rtd(config-if)#end
rtd#ping 1.1.1.9

 

注：其中包括了测试通不通的脚本,在配置好一个接口最好就测试一下,免得到最后再一起测试的时候没法应用你给路由器的配置，也就是还没有生效。在配置的时候千万要注意username和password要一致。