单臂路由的配置实例
设备如图:pc机2台分别为 pc2和pc3、二层交换机1个为 s1、路由器1个为 R1
   [实验拓扑]

实验拓扑
首先开始配置pc机的ip地址pc2:192.168.2.10 网关:192.168.2.1 pc3:192.168.3.10 网关:192.168.3.1 掩码都是24位的
下面来配置交换机,分配好vlan。(简单的我就不解释了)
Switch>enable
Switch#vlan d
% Warning: It is recommended to configure VLAN from config mode,
as VLAN database mode is being deprecated. Please consult user
documentation for configuring VTP/VLAN in config mode.
Switch(vlan)#vlan 2 name test01
VLAN 2 added:
Name: test01
Switch(vlan)#vlan 3 name test02
VLAN 3 added:
Name: test02 →设置好vlan ,这里只简单设置两个。
Switch(vlan)#exit
APPLY completed.
Exiting....
Switch#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#interface fa0/2
Switch(config-if)#switchport access vlan 2
Switch(config-if)#exit
Switch(config)#interface fa0/3
Switch(config-if)#switchport access vlan 3
Switch(config-if)#exit
Switch(config)#interface fa0/1
Switch(config-if)#switchport trunk encapsulation dot1q (2960等交换机只支持802.1q协议,这里忽略)
Switch(config-if)#switchport mode trunk
Switch(config-if)#switchport trunk allowed vlan all
Switch(config-if)#exit
Switch(config)#end
%SYS-5-CONFIG_I: Configured from console by console
Switch#write memory
Building configuration...
[OK]
下面来重点,配置单臂路由:
Router>enable
Router#config
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z. .................进入全局配置模式
Router(config)#interface fa0/0 ................进入和交换机连接的那个接口
Router(config-if)#no shutdown ................激活该端口
Router(config-if)#exit (这句可以没有)
Router(config)#interface fa0/0.1 ...........配置 子接口 这是配置单臂路由的关键,这个接口是个 逻辑接口,并不是实际存在的物理接口,但是功能却和物理接口是一样的。
Router(config-subif)#encapsulation dot1q 2 .......为这个接口配置802.1Q协议,最后面的 2 是vlan 号,这也是关键部分
Router(config-subif)#ip address 192.168.2.1 255.255.255.0 .........为该接口划分ip地址。
Router(config-subif)#exit
Router(config)#interface fa0/0.2 .....同样,进入第2个子接口,进行配置
Router(config-subif)#encapsulation dot1q 3 .........配置802.1Q协议
Router(config-subif)#ip address 192.168.3.1 255.255.255.0 ......划分ip地址和子网掩码
Router(config-subif)#end
%SYS-5-CONFIG_I: Configured from console by console ..........完成配置
下面是测试结果:
经过分别对两台机子互相ping的测试,可以发现能够ping通,说明实验成功