linux 2.6.35 内核配置 usb,Linux 2.6.24.4移植到S3C2410(nano2410)之：USB

Linux 2.6.24.4移植到S3C2410(nano2410)之：USB

【平台信息】

目标板(Nano2410)------------------------

CPU: S3C2410X

SDRAM:HY57V561620(32MB)

FLASH: K9F1208(64MB)

NET: CS8900

HOST---------------------------------------

Linux Realse Version:Fecora Cor 8 (FC8)

CrossCompiler:gcc-4.1.1/glibc-2.3.2

问题的提出:

内核配置时使用smdk2410的默认配置. U盘不能挂载!

插拔U盘提示信息为:

$ usb 1-1: USB disconnect, address 2

usb 1-1: new full speed USB device using s3c2410-ohci and address 3

usb 1-1: configuration #1 chosen from 1 choice

查看partitions下的分区信息,没有出现USB设备

root@kevin /proc

$ cat partitions

major minor#blocksname

3101024 mtdblock0

3113072 mtdblock1

31240960 mtdblock2

31320480 mtdblock3

root@kevin /dev

$ ls u*

urandomusbdev1.1_ep00 usbdev1.2usbdev1.2_ep01

usbdev1.1usbdev1.1_ep81usbdev1.2_ep00usbdev1.2_ep82

解决方法:

重新配置内核,启用SCSI device support, SCSI相关模块最好编译进内核,不要以module形式编译.

插上U盘后,显示:

usb 1-1: new full speed USB device using s3c2410-ohci and address 3

usb 1-1: configuration #1 chosen from 1 choice

scsi1 : SCSI emulation for USB Mass Storage devices

scsi 1:0:0:0: Direct-AccessUSB Flash Disk1.06 PQ: 0 ANSI: 0 CCS

sd 1:0:0:0: [sda] 129312 512-byte hardware sectors (66 MB)

sd 1:0:0:0: [sda] Write Protect is off

sd 1:0:0:0: [sda] Assuming drive cache: write through

sd 1:0:0:0: [sda] 129312 512-byte hardware sectors (66 MB)

sd 1:0:0:0: [sda] Write Protect is off

sd 1:0:0:0: [sda] Assuming drive cache: write through

sda: sda1

sda: p1 exceeds device capacity

sd 1:0:0:0: [sda] Attached SCSI removable disk

用dmesg查看信息:

dmesg

sd 0:0:0:0: [sda] 129312 512-byte hardware sectors (66 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 06 00 00

sd 0:0:0:0: [sda] Assuming drive cache: write through

sd 0:0:0:0: [sda] 129312 512-byte hardware sectors (66 MB)

sd 0:0:0:0: [sda] Write Protect is off

sd 0:0:0:0: [sda] Mode Sense: 00 06 00 00

sd 0:0:0:0: [sda] Assuming drive cache: write through

sda: sda1

sda: p1 exceeds device capacity

sd 0:0:0:0: [sda] Attached SCSI removable disk

selected clock c03200b4 (pclk) quot 27, calc 113169

root@kevin /

$ cat proc/partitions

major minor#blocksname

3101024 mtdblock0

3113072 mtdblock1

31240960 mtdblock2

31320480 mtdblock3

8064656 sda

8164656 sda1

u盘设备名为sda1.

$ mount -t vfat sda1 /mnt

Unable to load NLS charset cp437

FAT: codepage cp437 not found

mount: mounting sda1 on /mnt failed: Invalid argument

内核缺少cp437字符集.重新配置内核,在filesystems-->native language support->中选择Codepage 437和其他的一些常用的字符集.

重新mount

root@kevin /

$ mount -t vfat /dev/sda1 /mnt/usb

查看usb目录下被挂载的文件.

root@kevin /

$ ls /mnt/usb

070723_LE20C3.rardvpc3_tc003_070609.opj

070726_2101_LE20C3.raricebox.hex

080128_1313_UCOS_44B0iic pic

080128_1313_UCOS_44B0.rarldlinux.sys

???????!??.txtle20c3.rar

DVPC3_T002_070621-2.pcbmsvcr71.dll

DVPC3_TC002_070606_LAYOUT.DSNpcb footprint.xls

DVPC3_TC003_070609.DSNpcb_lib

DVPC3_TC003_070609_0.DBKrootfs.gz

DVPC3_TC03 GERBER.pcbsr81.exe

GPIO allocsyslinux.cfg

MEDIAPLAYER.DSNtest

avtest.c

bzImagetest.txt

ch375

OK,U盘挂载成功了~~~