traceroute命令详解linux,Linux traceroute命令使用详解

traceroute我们可以知道信息从你的计算机到互联网另一端的主机是走的什么路径。当然每次数据包由某一同样的出发点(source)到达某一同样的目的地(destination)走的路径可能会不一样，但基本上来说大部分时候所走的路由是相同的。

常见命令参数

Options:

-4 Use IPv4

-6 Use IPv6

-d --debug Enable socket level debugging

-F --dont-fragment Do not fragment packets

-f first_ttl --first=first_ttl

Start from the first_ttl hop (instead from 1)

-g gate,... --gateway=gate,...

Route packets through the specified gateway

(maximum 8 for IPv4 and 127 for IPv6)

-I --icmp Use ICMP ECHO for tracerouting

-T --tcp Use TCP SYN for tracerouting

-i device --interface=device

Specify a network interface to operate with

-m max_ttl --max-hops=max_ttl

Set the max number of hops (max TTL to be

reached). Default is 30

-N squeries --sim-queries=squeries

Set the number of probes to be tried

simultaneously (default is 16)

-n Do not resolve IP addresses to their domain names

-p port --port=port Set the destination port to use. It is either

initial udp port value for "default" method

(incremented by each probe, default is 33434), or

initial seq for "icmp" (incremented as well,

default from 1), or some constant destination

port for other methods (with default of 80 for

"tcp", 53 for "udp", etc.)

-t tos --tos=tos Set the TOS (IPv4 type of service) or TC (IPv6

traffic class) value for outgoing packets

-l flow_label --flowlabel=flow_label

Use specified flow_label for IPv6 packets

-w waittime --wait=waittime

Set the number of seconds to wait for response to

a probe (default is 5.0). Non-integer (float

point) values allowed too

-q nqueries --queries=nqueries

Set the number of probes per each hop. Default is

3

-r Bypass the normal routing and send directly to a

host on an attached network

-s src_addr --source=src_addr

Use source src_addr for outgoing packets

-z sendwait --sendwait=sendwait

Minimal time interval between probes (default 0).

If the value is more than 10, then it specifies a

number in milliseconds, else it is a number of

seconds (float point values allowed too)

-e --extensions Show ICMP extensions (if present), including MPLS

-A --as-path-lookups Perform AS path lookups in routing registries and

print results directly after the corresponding

addresses

-M name --module=name Use specified module (either builtin or external)

for traceroute operations. Most methods have

their shortcuts (`-I' means `-M icmp' etc.)

-O OPTS,... --options=OPTS,...

Use module-specific option OPTS for the

traceroute module. Several OPTS allowed,

separated by comma. If OPTS is "help", print info

about available options

--sport=num Use source port num for outgoing packets. Implies

`-N 1'

-U --udp Use UDP to particular port for tracerouting

(instead of increasing the port per each probe),

default port is 53

-UL Use UDPLITE for tracerouting (default dest port

is 53)

-P prot --protocol=prot Use raw packet of protocol prot for tracerouting

--mtu Discover MTU along the path being traced. Implies

`-F -N 1'

--back Guess the number of hops in the backward path and

print if it differs

-V --version Print version info and exit

--help Read this help and exit

常见命令展示

多命令使用

traceroute -n -m 5 -q 4 -w 3 www.baidu.com

说明： -n 显示IP地址，不查主机名， -m 设置跳数

-q 4每个网关发送4个数据包 -w 把对外发探测包的等待响应时间设置为3秒

探测包使用的基本UDP端口设置6888

traceroute -p 6888 www.baidu.com

绕过正常的路由表，直接发送到网络相连的主机

traceroute -r www.baidu.com

以上就是本文的全部内容，希望对大家的学习有所帮助，也希望大家多多支持我们。

时间： 2019-12-10