在一些低成本应用场景，需要在SPI flash上启动系统，这需要对Uboot和系统镜像做些适配。
本文介绍SPI Flash镜像的制作过程。
这里 使用 MX25L25645G, 32M SPI flash 作为启动介质，规划分区如下：
分区序号
分区大小
分区作用
地址空间及分区名
mtd0
1MB
spl+uboot
0x0000000-0x0100000 : “uboot”
mtd1
64KB
dtb文件
0x0100000-0x0110000: “dtb”
mtd2
4MB
linux内核
0x0110000-0x0510000 : “kernel”
mtd3
剩余
根文件系统
0x0510000-0x2000000 : “rootfs”
由于目前Uboot环境变量固定存放在1MB位置之内，所有留给uboot的空间固定到flash前1MB的位置不变。
每个分区的大小必须是擦除块大小的整数倍，MX25L25645G的擦除块大小是64KB。
下载包含spi驱动的体验版本uboot，该驱动目前尚未合并到主线
git clone -b v3s-spi-experimental https://github.com/Lichee-Pi/u-boot.git
执行 make ARCH=arm menuconfig 打开uboot菜单配置，进入到 Device Drivers ‣ SPI Flash Support
注意看一下自己flash的厂家名称，例如选上Macronix SPI flash support用来支持测试用的flash：MX25L25645G。
如果使用的是16MB以上的flash，需要勾选flash bank支持选项，否则最多只能读到16MB： CONFIG_SPI_FLASH_BAR
在文件 include/configs/sun8i.h 中添加默认bootcmd和bootargs的环境变量设置，注意添加的位置在“ #include ”的前边。
vi include/configs/sun8i.h¶
#define CONFIG_BOOTCOMMAND "sf probe 0; " \
"sf read 0x41800000 0x100000 0x10000; " \
"sf read 0x41000000 0x110000 0x400000; " \
"bootz 0x41000000 - 0x41800000"
#define CONFIG_BOOTARGS "console=ttyS0,115200 earlyprintk panic=5 rootwait " \
"mtdparts=spi32766.0:1M(uboot)ro,64k(dtb)ro,4M(kernel)ro,-(rootfs) root=31:03 rw rootfstype=jffs2"
环境命令解析：sf probe 0; //初始化Flash设备(CS拉低)
sf read 0x41800000 0x100000 0x10000; //从flash0x100000(1MB)位置读取dtb放到内存0x41800000偏移处。 //如果是bsp的bin，则是0x41d00000
sf read 0x41000000 0x110000 0x400000; //从flash0x110000(1MB+64KB)位置读取dtb放到内存0x41000000偏移处。
bootz 0x41000000 (内核地址)- 0x41800000(dtb地址) 启动内核
启动参数解析console=ttyS0,115200 earlyprintk panic=5 rootwait //在串口0上输出信息
mtdparts=spi32766.0:1M(uboot)ro,64k(dtb)ro,4M(kernel)ro,-(rootfs) root=31:03 rw rootfstype=jffs2 //spi32766.0是设备名，后面是分区大小，名字，读写属性。
root=31:03表示根文件系统是mtd3；jffs2格式
time make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- 2>&1 | tee build.log
会在目录下生成 u-boot-sunxi-with-spl.bin
linux内核基于github上的版本https://github.com/Lichee-Pi/linux.git，分支为最新的zero-4.13.y
执行 make ARCH=arm menuconfig 打开内核菜单配置，
进入到 Device Drivers ‣ Memory Technology Device (MTD) support ，
确保选择上mtd的 Command line partition table parsing 支持，该项目用来解析uboot传递过来的flash分区信息。
以及SPI-NOR 设备的支持。
添加对jffs2文件系统的支持，路径在 File systems ‣ Miscellaneous filesystems ‣ Journalling Flash File System v2 (JFFS2) support
修改dts配置添加spi flash节点
vi arch/arm/boot/dts/sun8i-v3s-licheepi-zero.dts
添加spi节点配置:
&spi0 {
status ="okay";
mx25l25635e:mx25l25635e@0 {
compatible = "jedec,spi-nor";
reg = <0x0>;
spi-max-frequency = <50000000>;
#address-cells = <1>;
#size-cells = <1>;
};
};
这里的flash型号需要在下表之中，否则将无法识别：(注意容量也一定要对应)
static const struct spi_device_id m25p_ids[] = {
/*
* Allow non-DT platform devices to bind to the "spi-nor" modalias, and
* hack around the fact that the SPI core does not provide uevent
* matching for .of_match_table
*/
{"spi-nor"},
/*
* Entries not used in DTs that should be safe to drop after replacing
* them with "spi-nor" in platform data.
*/
{"s25sl064a"}, {"w25x16"}, {"m25p10"}, {"m25px64"},
/*
* Entries that were used in DTs without "jedec,spi-nor" fallback and
* should be kept for backward compatibility.
*/
{"at25df321a"}, {"at25df641"}, {"at26df081a"},
{"mx25l4005a"}, {"mx25l1606e"}, {"mx25l6405d"}, {"mx25l12805d"},
{"mx25l25635e"},{"mx66l51235l"},
{"n25q064"}, {"n25q128a11"}, {"n25q128a13"}, {"n25q512a"},
{"s25fl256s1"}, {"s25fl512s"}, {"s25sl12801"}, {"s25fl008k"},
{"s25fl064k"},
{"sst25vf040b"},{"sst25vf016b"},{"sst25vf032b"},{"sst25wf040"},
{"m25p40"}, {"m25p80"}, {"m25p16"}, {"m25p32"},
{"m25p64"}, {"m25p128"},
{"w25x80"}, {"w25x32"}, {"w25q32"}, {"w25q32dw"},
{"w25q80bl"}, {"w25q128"}, {"w25q256"},
/* Flashes that can't be detected using JEDEC */
{"m25p05-nonjedec"}, {"m25p10-nonjedec"}, {"m25p20-nonjedec"},
{"m25p40-nonjedec"}, {"m25p80-nonjedec"}, {"m25p16-nonjedec"},
{"m25p32-nonjedec"}, {"m25p64-nonjedec"}, {"m25p128-nonjedec"},
/* Everspin MRAMs (non-JEDEC) */
{ "mr25h256" }, /* 256 Kib, 40 MHz */
{ "mr25h10" }, /* 1 Mib, 40 MHz */
{ "mr25h40" }, /* 4 Mib, 40 MHz */
{ },
};
退出菜单配置并编译内核和dts¶
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- -j32
make ARCH=arm CROSS_COMPILE=arm-linux-gnueabihf- dtbs
首先选择rootfs文件系统，我是用的是群朋提供的最小根文件系统 rootfs-brmin.tar.gz，大小只有3M左右，下载地址在
https://pan.baidu.com/share/link?
shareid=1432204556&uk=3658413294#list/path=%2F
Lichee Zero>zero_imager.zip
Flash支持jffs2文件系统格式，所以需要使用此该rootfs制作jffs2文件系统镜像、
下载jffs2文件系统制作工具
apt-get install mtd-utils
解压 rootfs-brmin.tar.gz
tar xzvf rootfs-brmin.tar.gz
计算好jffs的大小，可以使用zero_imager里的 make_jffs2.sh 32 生成
总空间是32M-1M-64K-4M=0x1AF0000
mkfs.jffs2 -s 0x100 -e 0x10000 -p 0x1AF0000 -d rootfs/ -o jffs2.img
页大小0x100 256字节
块大小0x10000 64k
jffs2分区总空间0x1AF0000
jffs2.img是生成的文件系统镜像。
最后将uboot，dtb，kernel，rootfs打包成一个系统镜像，命令如下；(即zero_imager里的 make_spiflash.sh 32 dock)
#!/bin/sh
dd if=/dev/zero of=flashimg.bin bs=1M count=$1
dd if=u-boot-sunxi-with-spl-$2.bin of=flashimg.bin bs=1K conv=notrunc
dd if=sun8i-v3s-licheepi-zero-$2.dtb of=flashimg.bin bs=1K seek=1024 conv=notrunc
dd if=zImage of=flashimg.bin bs=1K seek=1088 conv=notrunc
dd if=jffs2.img of=flashimg.bin bs=1K seek=5184 conv=notrunc
第一步： 生成一个空文件，大小是32MB
第二步： 将uboot添加到文件开头
第三步： 将dtb放到1M偏移处
第四步： 将kernel放到1M+64K偏移处
第五步： 将rootfs放到1M+64K+4M偏移处
偏移大小是seek，单位是KB。
执行完毕后生成镜像文件 flashimg.bin
git clone -b spi-rebase https://github.com/Icenowy/sunxi-tools.git
注解
注意是spi-rebase分支。
进入工具目录执行 make && sudo make install
如果出现：fel_lib.c:26:20: fatal error: libusb.h: No such file or directory，那需要安装libusb：
sudo apt-get install libusb-1.0-0-dev
Zero有一个usb下载模式称为fel模式，进入fel模式有下面几种方式：
TF卡和spi flash 同时没有可启动镜像;也就是说你不插卡，且焊接的是新的或者没有有效镜像的spi flash，那就上电自动进入fel下载模式
TF卡中有进入fel模式的特殊固件 fel-sdboot.sunxi如果你的spiflash已经有了启动镜像，那么需要在TF卡中烧入一个sunxi提供的 启动工具
( dd if=fel-sdboot.sunxi of=/dev/mmcblk0 bs=1024 seek=8 )，
那么插入该TF卡启动会进入fel模式；
上电时SPI_MISO拉低到地该引脚为boot引脚，上电时出于低电平即会进入fel下载模式。
进入fel模式后使用usb数据线连接pc和zero,即可进行操作。
sudo sunxi-fel version #查看连接的cpu信息
AWUSBFEX soc=00001681(V3s) 00000001 ver=0001 44 08 scratchpad=00007e00 00000000 00000000
sudo sunxi-fel spiflash-info #显示flash信息
Manufacturer: Unknown (C2h), model: 20h, size: 33554432 bytes.
执行如下命令烧入我们前边制作好的镜像文件
sudo sunxi-fel -p spiflash-write 0 flashimg.bin
# -p 显示进度条
# spiflash-info Retrieves basic information
# spiflash-hex[dump] addr length Dumps SPI flash region in hex
# spiflash-read addr length file Write SPI flash contents into file
# spiflash-write addr file Store file contents into SPI flash
SPI flash下载速度约50KB/s，等待5分钟(16MB)或者10分钟(32MB)，烧写完成，如果一切顺利，重新上电zero那么就会进入linux系统了，账号是root没有密码。
U-Boot SPL 2017.01-rc2-00073-gdd6e874-dirty (Oct 14 2017 - 16:33:01)
DRAM: 64 MiB
Trying to boot from sunxi SPI
U-Boot 2017.01-rc2-00073-gdd6e874-dirty (Oct 14 2017 - 16:33:01 +0000) Allwinner Technology
CPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
*** Warning - bad CRC, using default environment
Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In: serial@01c28000
Out: serial@01c28000
Err: serial@01c28000
U-Boot 2017.01-rc2-00073-gdd6e874-dirty (Oct 14 2017 - 16:33:01 +0000) Allwinner Technology
CPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
*** Warning - bad CRC, using default environment
Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 33000kHz = 33000kHz: (1 * 3MHz * 66) / 6
In: serial@01c28000
Out: serial@01c28000
Err: serial@01c28000
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
device 0 offset 0x100000, size 0x10000
SF: 65536 bytes @ 0x100000 Read: OK
device 0 offset 0x110000, size 0x400000
SF: 4194304 bytes @ 0x110000 Read: OK
## Flattened Device Tree blob at 41800000
Booting using the fdt blob at 0x41800000
Loading Device Tree to 42dfa000, end 42dffc48 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.13.0-licheepi-zero+ (root@bf756b445919) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #10 SMP Sat Oct 14 16:59:37 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Lichee Pi Zero XFJ
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 16 pages/cpu @c3de6000 s33868 r8192 d23476 u65536
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15883
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi32766.0:1M(uboot)ro,64k(dtb)ro,4M(kernel)ro,-(rootfs) root=31:03 rw rootfstype=jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 53576K/64036K available (6144K kernel code, 229K rwdata, 1512K rodata, 1024K init, 265K bss, 10460K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc4000000 - 0xff800000 ( 952 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc3e89000 ( 62 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0700000 (7136 kB)
[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)
[ 0.000000] .data : 0xc0a00000 - 0xc0a39580 ( 230 kB)
[ 0.000000] .bss : 0xc0a3f65c - 0xc0a81b54 ( 266 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU event tracing is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000008] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000019] Switching to timer-based delay loop, resolution 41ns
[ 0.000187] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000420] Console: colour dummy device 80x30
[ 0.000457] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000475] pid_max: default: 32768 minimum: 301
[ 0.000604] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000619] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001213] CPU: Testing write buffer coherency: ok
[ 0.001589] /cpus/cpu@0 missing clock-frequency property
[ 0.001612] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002074] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.002259] Hierarchical SRCU implementation.
[ 0.002765] smp: Bringing up secondary CPUs ...
[ 0.002781] smp: Brought up 1 node, 1 CPU
[ 0.002790] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.002797] CPU: All CPU(s) started in SVC mode.
[ 0.003559] devtmpfs: initialized
[ 0.006668] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.006932] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.006967] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.007136] pinctrl core: initialized pinctrl subsystem
[ 0.008026] random: get_random_u32 called from bucket_table_alloc+0xf4/0x244 with crng_init=0
[ 0.008162] NET: Registered protocol family 16
[ 0.008655] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.009800] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.009817] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.023260] SCSI subsystem initialized
[ 0.023562] usbcore: registered new interface driver usbfs
[ 0.023652] usbcore: registered new interface driver hub
[ 0.023747] usbcore: registered new device driver usb
[ 0.023983] Linux video capture interface: v2.00
[ 0.024036] pps_core: LinuxPPS API ver. 1 registered
[ 0.024044] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.024064] PTP clock support registered
[ 0.024282] Advanced Linux Sound Architecture Driver Initialized.
[ 0.024955] Bluetooth: Core ver 2.22
[ 0.025029] NET: Registered protocol family 31
[ 0.025037] Bluetooth: HCI device and connection manager initialized
[ 0.025056] Bluetooth: HCI socket layer initialized
[ 0.025066] Bluetooth: L2CAP socket layer initialized
[ 0.025097] Bluetooth: SCO socket layer initialized
[ 0.026313] clocksource: Switched to clocksource arch_sys_counter
[ 0.037157] NET: Registered protocol family 2
[ 0.037746] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.037780] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[ 0.037803] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.037937] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.037985] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.038205] NET: Registered protocol family 1
[ 0.038812] RPC: Registered named UNIX socket transport module.
[ 0.038833] RPC: Registered udp transport module.
[ 0.038840] RPC: Registered tcp transport module.
[ 0.038846] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.040940] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.048568] NFS: Registering the id_resolver key type
[ 0.048618] Key type id_resolver registered
[ 0.048627] Key type id_legacy registered
[ 0.048672] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.050140] random: fast init done
[ 0.053091] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249)
[ 0.053111] io scheduler noop registered
[ 0.053118] io scheduler deadline registered
[ 0.053358] io scheduler cfq registered (default)
[ 0.053368] io scheduler mq-deadline registered
[ 0.053376] io scheduler kyber registered
[ 0.057981] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.058417] name=allwinner,sun7i-a20-pwm
[ 0.058432] npwm=2
[ 0.127969] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.131445] console [ttyS0] disabled
[ 0.151721] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[ 0.780269] console [ttyS0] enabled
[ 0.805297] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 34, base_baud = 1500000) is a U6_16550A
[ 0.835807] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A
[ 0.848508] libphy: Fixed MDIO Bus: probed
[ 0.853001] usbcore: registered new interface driver r8152
[ 0.858614] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.865135] ehci-platform: EHCI generic platform driver
[ 0.870676] ehci-platform 1c1a000.usb: EHCI Host Controller
[ 0.876350] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 1
[ 0.884288] ehci-platform 1c1a000.usb: irq 25, io mem 0x01c1a000
[ 0.916344] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00
[ 0.923490] hub 1-0:1.0: USB hub found
[ 0.927421] hub 1-0:1.0: 1 port detected
[ 0.931878] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.938171] ohci-platform: OHCI generic platform driver
[ 0.943713] ohci-platform 1c1a400.usb: Generic Platform OHCI controller
[ 0.950433] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 2
[ 0.958360] ohci-platform 1c1a400.usb: irq 26, io mem 0x01c1a400
[ 1.031375] hub 2-0:1.0: USB hub found
[ 1.035198] hub 2-0:1.0: 1 port detected
[ 1.042745] udc-core: couldn't find an available UDC - added [g_ether] to list of pending drivers
[ 1.052618] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0
[ 1.059513] sun6i-rtc 1c20400.rtc: RTC enabled
[ 1.064048] i2c /dev entries driver
[ 1.069222] usbcore: registered new interface driver uvcvideo
[ 1.074974] USB Video Class driver (1.1.1)
[ 1.079833] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 1.087825] Bluetooth: HCI UART driver ver 2.3
[ 1.092273] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 1.156357] sunxi-mmc 1c0f000.mmc: base:0xc407b000 irq:23
[ 1.162805] usbcore: registered new interface driver usbhid
[ 1.168456] usbhid: USB HID core driver
[ 1.174122] NET: Registered protocol family 17
[ 1.178794] Key type dns_resolver registered
[ 1.183228] Registering SWP/SWPB emulation handler
[ 1.193806] simple-framebuffer 43e89000.framebuffer: framebuffer at 0x43e89000, 0x177000 bytes, mapped to 0xc4400000
[ 1.204454] simple-framebuffer 43e89000.framebuffer: format=x8r8g8b8, mode=800x480x32, linelength=3200
[ 1.222854] Console: switching to colour frame buffer device 100x30
[ 1.235317] simple-framebuffer 43e89000.framebuffer: fb0: simplefb registered!
[ 1.243916] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 1.255346] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 1.261186] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 3
[ 1.270315] hub 3-0:1.0: USB hub found
[ 1.274184] hub 3-0:1.0: 1 port detected
[ 1.279498] using random self ethernet address
[ 1.283985] using random host ethernet address
[ 1.289160] usb0: HOST MAC 8e:ca:5f:61:47:a8
[ 1.293475] usb0: MAC f2:57:f4:ad:74:af
[ 1.297416] using random self ethernet address
[ 1.301858] using random host ethernet address
[ 1.306400] g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
[ 1.313010] g_ether gadget: g_ether ready
[ 1.317402] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01 00:56:52 UTC (3412)
[ 1.325834] vcc3v0: disabling
[ 1.328911] vcc5v0: disabling
[ 1.331879] ALSA device list:
[ 1.334841] No soundcards found.
[ 1.339241] VFS: Cannot open root device "31:03" or unknown-block(31,3): error -19
[ 1.346938] Please append a correct "root=" boot option; here are the available partitions:
[ 1.355286] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,3)
[ 1.363630] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.0-licheepi-zero+ #10
[ 1.370926] Hardware name: Allwinner sun8i Family
[ 1.375664] [] (unwind_backtrace) from [] (show_stack+0x10/0x14)
[ 1.383408] [] (show_stack) from [] (dump_stack+0x84/0x98)
[ 1.390632] [] (dump_stack) from [] (panic+0xdc/0x248)
[ 1.397507] [] (panic) from [] (mount_block_root+0x188/0x25c)
[ 1.404985] [] (mount_block_root) from [] (mount_root+0x120/0x128)
[ 1.412894] [] (mount_root) from [] (prepare_namespace+0x150/0x194)
[ 1.420891] [] (prepare_namespace) from [] (kernel_init_freeable+0x1bc/0x1cc)
[ 1.429755] [] (kernel_init_freeable) from [] (kernel_init+0x8/0x108)
[ 1.437927] [] (kernel_init) from [] (ret_from_fork+0x14/0x3c)
[ 1.445499] Rebooting in 5 seconds..
U-Boot SPL 2017.01-rc2-00073-gdd6e874-dirty (Nov 26 2017 - 15:10:41)
DRAM: 64 MiB
Trying to boot from sunxi SPICPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected w25q128bv with page size 256 Bytes, erase size 64 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 27000kHz = 27000kHz: (1 * 3MHz * 54) / 6
beep 0
beep 1
beep 0
beep 1
beep 0
beep 1
In: serial@01c28000
Out: serial@01c28000
Err: serial@01c28000
CPU: Allwinner V3s (SUN8I 1681)
Model: Lichee Pi Zero
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: Detected w25q128bv with page size 256 Bytes, erase size 64 KiB, total 16 MiB
*** Warning - bad CRC, using default environment
Setting up a 800x480 lcd console (overscan 0x0)
dotclock: 27000kHz = 27000kHz: (1 * 3MHz * 54) / 6
beep 0
beep 1
beep 0
beep 1
beep 0
beep 1
In: serial@01c28000
Out: serial@01c28000
Err: serial@01c28000
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
SF: Detected w25q128bv with page size 256 Bytes, erase size 64 KiB, total 16 MiB
device 0 offset 0x100000, size 0x10000
SF: 65536 bytes @ 0x100000 Read: OK
device 0 offset 0x110000, size 0x400000
SF: 4194304 bytes @ 0x110000 Read: OK
## Flattened Device Tree blob at 41800000
Booting using the fdt blob at 0x41800000
Loading Device Tree to 42dfa000, end 42dffbfa ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.13.0-licheepi-zero+ (root@bf756b445919) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #95 SMP Mon Nov 27 01:20:31 UTC 2017
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Lichee Pi Zero XFJ
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] percpu: Embedded 15 pages/cpu @c3de7000 s32588 r8192 d20660 u61440
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15883
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk panic=5 rootwait mtdparts=spi32766.0:1M(uboot)ro,64k(dtb)ro,4M(kernel)ro,-(rootfs) root=31:03 rw rootfstype=jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 55708K/64036K available (4096K kernel code, 187K rwdata, 1144K rodata, 1024K init, 232K bss, 8328K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc4000000 - 0xff800000 ( 952 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc3e89000 ( 62 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0500000 (5088 kB)
[ 0.000000] .init : 0xc0700000 - 0xc0800000 (1024 kB)
[ 0.000000] .data : 0xc0800000 - 0xc082ee00 ( 188 kB)
[ 0.000000] .bss : 0xc08332d0 - 0xc086d584 ( 233 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU event tracing is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000009] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000024] Switching to timer-based delay loop, resolution 41ns
[ 0.000214] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000465] Console: colour dummy device 80x30
[ 0.000506] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000525] pid_max: default: 32768 minimum: 301
[ 0.000672] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000692] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.001393] CPU: Testing write buffer coherency: ok
[ 0.001817] /cpus/cpu@0 missing clock-frequency property
[ 0.001842] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002345] Setting up static identity map for 0x40100000 - 0x40100060
[ 0.002541] Hierarchical SRCU implementation.
[ 0.003148] smp: Bringing up secondary CPUs ...
[ 0.003163] smp: Brought up 1 node, 1 CPU
[ 0.003175] SMP: Total of 1 processors activated (48.00 BogoMIPS).
[ 0.003184] CPU: All CPU(s) started in SVC mode.
[ 0.004066] devtmpfs: initialized
[ 0.007259] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.007578] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.007614] futex hash table entries: 256 (order: 2, 16384 bytes)
[ 0.007813] pinctrl core: initialized pinctrl subsystem
[ 0.008896] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.010158] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.010179] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.022957] SCSI subsystem initialized
[ 0.023159] usbcore: registered new interface driver usbfs
[ 0.023235] usbcore: registered new interface driver hub
[ 0.023362] usbcore: registered new device driver usb
[ 0.023474] Linux video capture interface: v2.00
[ 0.023517] pps_core: LinuxPPS API ver. 1 registered
[ 0.023526] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti
[ 0.023695] Advanced Linux Sound Architecture Driver Initialized.
[ 0.024215] clocksource: Switched to clocksource arch_sys_counter
[ 0.039085] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.046435] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.046808] jffs2: version 2.2. (NAND) ? 2001-2006 Red Hat, Inc.
[ 0.048756] random: fast init done
[ 0.052407] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.052432] io scheduler noop registered
[ 0.052442] io scheduler deadline registered
[ 0.052669] io scheduler cfq registered (default)
[ 0.052681] io scheduler mq-deadline registered
[ 0.052690] io scheduler kyber registered
[ 0.057653] sun8i-v3s-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.058150] name=allwinner,sun7i-a20-pwm
[ 0.058168] npwm=2
[ 0.139525] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.143224] console [ttyS0] disabled
[ 0.163532] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 33, base_baud = 1500000) is a U6_16550A
[ 0.676919] console [ttyS0] enabled
[ 0.702093] 1c28400.serial: ttyS1 at MMIO 0x1c28400 (irq = 34, base_baud = 1500000) is a U6_16550A
[ 0.732771] 1c28800.serial: ttyS2 at MMIO 0x1c28800 (irq = 35, base_baud = 1500000) is a U6_16550A
[ 0.747219] m25p80 spi32766.0: w25q128 (16384 Kbytes)
[ 0.752288] in cmdline partion
[ 0.755486] p4 : size=100000
[ 0.758369] p4 : size=10000
[ 0.761160] p4 : size=400000
[ 0.764037] p4 : size=ffffffff
[ 0.767126] spi32766.0: parser cmdlinepart: 4
[ 0.771481] 4 cmdlinepart partitions found on MTD device spi32766.0
[ 0.777758] Creating 4 MTD partitions on "spi32766.0":
[ 0.782904] 0x000000000000-0x000000100000 : "uboot"
[ 0.789535] 0x000000100000-0x000000110000 : "dtb"
[ 0.795874] 0x000000110000-0x000000510000 : "kernel"
[ 0.802292] 0x000000510000-0x000001000000 : "rootfs"
[ 0.809706] sun6i-rtc 1c20400.rtc: rtc core: registered rtc-sun6i as rtc0
[ 0.816602] sun6i-rtc 1c20400.rtc: RTC enabled
[ 0.821153] i2c /dev entries driver
[ 0.826715] sunxi-wdt 1c20ca0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[ 0.835775] usbcore: registered new interface driver usbhid
[ 0.841355] usbhid: USB HID core driver
[ 0.846926] Registering SWP/SWPB emulation handler
[ 0.856875] simple-framebuffer 43e89000.framebuffer: framebuffer at 0x43e89000, 0x177000 bytes, mapped to 0xc4400000
[ 0.867547] simple-framebuffer 43e89000.framebuffer: format=x8r8g8b8, mode=800x480x32, linelength=3200
[ 0.885830] Console: switching to colour frame buffer device 100x30
[ 0.900736] simple-framebuffer 43e89000.framebuffer: fb0: simplefb registered!
[ 0.908121] sun6i-rtc 1c20400.rtc: setting system clock to 1970-01-01 02:33:59 UTC (9239)
[ 0.916575] vcc3v0: disabling
[ 0.919554] vcc3v3: disabling
[ 0.922519] vcc5v0: disabling
[ 0.925539] ALSA device list:
[ 0.928507] No soundcards found.
[ 0.994326] random: crng init done
[ 1.519199] VFS: Mounted root (jffs2 filesystem) on device 31:3.
[ 1.526365] devtmpfs: mounted
[ 1.530825] Freeing unused kernel memory: 1024K
Starting logging: OK
Starting mdev...
modprobe: can't change directory to '/lib/modules': No such file or directory
Initializing random number generator... done.
Starting network: ip: socket: Function not implemented
ip: socket: Function not implemented
FAIL
Welcome to Lichee Pi
Lichee login:
sunxi-fel v1.4.1-87-g78a7566
Usage: sunxi-fel [options] command arguments... [command...]
-h, --help Print this usage summary and exit
-v, --verbose Verbose logging
-p, --progress "write" transfers show a progress bar
-l, --list Enumerate all (USB) FEL devices and exit
-d, --dev bus:devnum Use specific USB bus and device number
--sid SID Select device by SID key (exact match)
spl file Load and execute U-Boot SPL
If file additionally contains a main U-Boot binary
(u-boot-sunxi-with-spl.bin), this command also transfers that
to memory (default address from image), but won't execute it.
uboot file-with-spl like "spl", but actually starts U-Boot
U-Boot execution will take place when the fel utility exits.
This allows combining "uboot" with further "write" commands
(to transfer other files needed for the boot).
hex[dump] address length Dumps memory region in hex
dump address length Binary memory dump
exe[cute] address Call function address
reset64 address RMR request for AArch64 warm boot
memmove dest source size Copy bytes within device memory
readl address Read 32-bit value from device memory
writel address value Write 32-bit value to device memory
read address length file Write memory contents into file
write address file Store file contents into memory
write-with-progress addr file "write" with progress bar
write-with-gauge addr file Output progress for "dialog --gauge"
write-with-xgauge addr file Extended gauge output (updates prompt)
multi[write] # addr file ... "write-with-progress" multiple files,
sharing a common progress status
multi[write]-with-gauge ... like their "write-with-*" counterpart,
multi[write]-with-xgauge ... but following the 'multi' syntax:
addr file [addr file [...]]
echo-gauge "some text" Update prompt/caption for gauge output
ver[sion] Show BROM version
sid Retrieve and output 128-bit SID key
clear address length Clear memory
fill address length value Fill memory
spiflash-info Retrieves basic information
spiflash-hex[dump] addr length Dumps SPI flash region in hex
spiflash-read addr length file Write SPI flash contents into file
spiflash-write addr file Store file contents into SPI flash
2439
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
