linux6.5做bond1,Linux CentOS 7 多网卡配置bond模式 bond1 bond5 bond6-Go语言中文社区

最新推荐文章于 2023-10-24 10:57:53 发布

邵苏

最新推荐文章于 2023-10-24 10:57:53 发布

阅读量611

点赞数

文章标签： linux6.5做bond1

https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Networking_Guide/sec-Network_Bonding_Using_the_Command_Line_Interface.html

Linux CentOS 7 多网卡配置bond模式 bond1 bond5 bond6

网卡绑定mode共有七种(0~6) bond0、bond1、bond2、bond3、bond4、bond5、bond6

常用的有四种

mode=0：(balance-rr) Round-robin policy(平衡抡循环策略)平衡负载模式，有自动备援，但需要”Switch”支援及设定。

mode=1，(active-backup) Active-backup policy(主-备份策略)只有一个设备处于活动状态，当一个宕掉另一个马上由备份转换为主设备。mac地址是外部可见得，从外面看来，bond的MAC地址是唯一的。

mode=5，(balance-tlb) Adaptive transmit load balancing(适配器传输负载均衡)不需要任何特别的switch(交换机)支持的通道bonding。

mode=6，(balance-alb) Adaptive load balancing(适配器适应性负载均衡)该模式包含了balance-tlb模式，同时加上针对IPV4流量的接收负载均衡(receive load balance, rlb)，而且不需要任何switch(交换机)的支持。接收负载均衡是通过ARP协商实现的

mode=1，(active-backup) Active-backup policy(主-备份策略)

在Centos 7中，我们可以使用modinfo bonding 命令查看bonding模块的信息，默认情况下bonding模块没有被加载

以root用户登录，输入如下的命令进行开启加载bonding模块

modprobe --first-time bonding //--first-time Fail if module already inserted or removed

cat /etc/sysconfig/network-scripts/ifcfg-bond1

DEVICE=bond1

BONDING_OPTS="resend_igmp=1 updelay=0 use_carrier=1 miimon=100 downdelay=0 xmit_hash_policy=0 primary_reselect=0 fail_over_mac=0 arp_validate=0 mode=active-backup primary=eno16777736 arp_interval=0 ad_select=0"

TYPE=Bond

BONDING_MASTER=yes

BOOTPROTO=none

IPADDR=192.168.199.235

PREFIX=24

DEFROUTE=yes

PEERDNS=yes

PEERROUTES=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

IPV6_FAILURE_FATAL=no

NAME="Bond connection 1"

UUID=e110d205-848e-4527-8cb1-2b3ac76cfb9b

ONBOOT=yes

cat /etc/sysconfig/network-scripts/ifcfg-eno33554960

HWADDR=00:0C:29:1B:57:14

TYPE=Ethernet

BOOTPROTO=none 修改

DEFROUTE=yes

PEERDNS=yes

PEERROUTES=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

IPV6_FAILURE_FATAL=no

NAME=eno33554960

UUID=ef35e777-0bc3-4afa-ad54-490e1543242a

ONBOOT=yes 修改

[root@www.zhangfangzhou.cn ~]# cat /proc/net/bonding/bond1

Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: fault-tolerance (active-backup)

Primary Slave: eno16777736 (primary_reselect always)

Currently Active Slave: eno16777736

MII Status: up

MII Polling Interval (ms): 0

Up Delay (ms): 0

Down Delay (ms): 0

Slave Interface: eno16777736

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:0a

Slave queue ID: 0

Slave Interface: eno33554960

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:14

Slave queue ID: 0

Slave Interface: eno50332184

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:1e

Slave queue ID: 0

Slave Interface: eno67109408

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:28

Slave queue ID: 0

------------------------------------------------------------------------------------------------------------------------

CentOS7手动配置bond6(balance-alb) Adaptive load balancing(适配器适应性负载均衡)

1、在Centos 7中，我们可以使用modinfo bonding 命令查看bonding模块的信息，默认情况下bonding模块没有被加载

以root用户登录，输入如下的命令进行开启加载bonding模块

modprobe --first-time bonding //--first-time Fail if module already inserted or removed

2、创建bond0配置文件，创建/etc/sysconfig/network-scripts/ifcfg-bond0文件，加入如下内容

cat /etc/sysconfig/network-scripts/ifcfg-bond0

DEVICE=bond0

TYPE=Bond

BONDING_MASTER=yes

BOOTPROTO=none

DEFROUTE=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_FAILURE_FATAL=no

NAME="bond0"

IPADDR=192.168.199.223

PREFIX=24

ONBOOT=yes

BONDING_OPTS="resend_igmp=1 updelay=0 use_carrier=1 miimon=100 downdelay=0 xmit_hash_policy=0 primary_reselect=0 fail_over_mac=0 arp_validate=0 mode=balance-alb arp_interval=0 ad_select=0"

PEERDNS=yes

PEERROUTES=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

其中BONDING_OPTS指定bonding的模式，其中10.101.230.30/27将作为bond0的ip地址

3、配置e网卡配置文件，文件位于/etc/sysconfig/network-scripts/目录

vi ifcfg-eno16777736

TYPE=Ethernet

BOOTPROTO=none 修改

DEFROUTE=yes

PEERDNS=yes

PEERROUTES=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

IPV6_FAILURE_FATAL=no

NAME=eno1

UUID=26ea0bd1-0837-4b1a-9039-f147abd19632

DEVICE=eno16777736

ONBOOT=yes 修改

#以下两项为新增配置选项

MASTER=bond0

SLAVE=yes

systemctl restart network.service //重启网络服务

[root@www.zhangfangzhou.cn~]# cat /proc/net/bonding/bond0

Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)

Bonding Mode: adaptive load balancing

Primary Slave: None

Currently Active Slave: eno33554960

MII Status: up

MII Polling Interval (ms): 100

Up Delay (ms): 0

Down Delay (ms): 0

Slave Interface: eno16777736

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 1

Permanent HW addr: 00:0c:29:1b:57:0a

Slave queue ID: 0

Slave Interface: eno33554960

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:14

Slave queue ID: 0

Slave Interface: eno50332184

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:1e

Slave queue ID: 0

Slave Interface: eno67109408

MII Status: up

Speed: 1000 Mbps

Duplex: full

Link Failure Count: 0

Permanent HW addr: 00:0c:29:1b:57:28

Slave queue ID: 0

------------------------------------------------------------

nutui配置bond6 (balance-alb) Adaptive load balancing(适配器适应性负载均衡)

https://access.redhat.com/documentation/en-US/Red_Hat_Enterprise_Linux/7/html/Networking_Guide/sec-Configure_Bonding_Using_the_Text_User_Interface_nmtui.html

[root@www.zhangfangzhou.cn network-scripts]# cat ifcfg-Bond_connection_1

DEVICE=bond0

TYPE=Bond

BONDING_MASTER=yes

BOOTPROTO=dhcp

DEFROUTE=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_FAILURE_FATAL=no

NAME="Bond connection 1"

UUID=5aa07976-3cc3-4db2-b9a8-af598906d263

ONBOOT=yes

BONDING_OPTS="resend_igmp=1 updelay=0 use_carrier=1 miimon=100 downdelay=0 xmit_hash_policy=0 primary_reselect=0 fail_over_mac=0 arp_validate=0 mode=balance-alb arp_interval=0 ad_select=0"

PEERDNS=yes

PEERROUTES=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

[root@www.zhangfangzhou.cn network-scripts]# cat ifcfg-eno16777736

HWADDR=00:0C:29:00:50:D4

TYPE=Ethernet

BOOTPROTO=dhcp

DEFROUTE=yes

PEERDNS=yes

PEERROUTES=yes

IPV4_FAILURE_FATAL=no

IPV6INIT=yes

IPV6_AUTOCONF=yes

IPV6_DEFROUTE=yes

IPV6_PEERDNS=yes

IPV6_PEERROUTES=yes

IPV6_FAILURE_FATAL=no

NAME=eno16777736

UUID=600f243a-ef20-4b91-8e5c-02a21b49cfb3

ONBOOT=no

[root@www.zhangfangzhou.cn network-scripts]# cat ifcfg-Ethernet_connection_1

TYPE=Ethernet

NAME="Ethernet connection 1"

UUID=a7f3051a-0aac-45fd-a019-75b9db495736

DEVICE=eno16777736

ONBOOT=yes

MASTER=5aa07976-3cc3-4db2-b9a8-af598906d263

SLAVE=yes

------------------------------------------------------------------------------------------------------------------------

配置mode=5，(balance-tlb) Adaptive transmit load balancing(适配器传输负载均衡)

cat /etc/sysconfig/network-scripts/ifcfg-bond5

bond5

DEVICE=bond5

TYPE=Bond

NAME=bond5

BONDING_MASTER=yes

BOOTPROTO=none

ONBOOT=yes

IPADDR=10.216.13.3

NETMASK=255.255.255.0

BONDING_OPTS="resend_igmp=1 updelay=0 use_carrier=1 miimon=100 downdelay=0 xmit_hash_policy=0 primary_reselect=0 fail_over_mac=0 arp_validate=0 mode=balance-tlb arp_interval=0 ad_select=0"