惠普计算机X9W2AV参数,MAX220CPE,MAX220CPE pdf中文资料,MAX220CPE引脚图,MAX220CPE电路-Datasheet-电子工程世界...

最新推荐文章于 2022-08-17 11:27:36 发布

电路和微电子考研

最新推荐文章于 2022-08-17 11:27:36 发布

阅读量446

点赞数

文章标签：惠普计算机X9W2AV参数

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

General Description Benefits and Features

The MAX220–MAX249 family of line drivers/receivers is Saves Board Space

intended for all EIA/TIA-232E and V.28/V.24 communica- • Integrated Charge Pump Circuitry

tions interfaces, particularly applications where ±12V is

not available. • Eliminates the Need for a Bipolar ±12V Supply

The MAX225, MAX233, MAX235, and MAX245/MAX246/ • Enables Single Supply Operation from +5V Supply

MAX247 use no external components and are • Integrated Capacitors (MAX223, MAX233, MAX235,

recommended for applications where printed circuit MAX245-MAX247)

board space is critical.

The MAX220-MAX249 are offered in 26 different pack- Saves Power for Reduced Power Requirements

ages with temperatures from 0 to +70°C up to -55°C to • 5µW Shutdown Mode

+125°C. See ordering information table at the end of the

data sheet for all package and temperature options. Ordering Information and Selection Table appears at end

Applications of data sheet.

• Interface Translation

• Multidrop RS-232 Networks

• Portable Diagnostics Equipment

AutoShutdown and UCSP are trademarks of Maxim Integrated

Products, Inc.

MAX220/MAX232/MAX232A Pin Configuration and Typical Operating Circuit

+5V INPUT C3

TOP VIEW

+ 16

C1+ 1 16 VCC 1 C1+ VCC V+ 2 +10V

C1 3 +5V TO +10V

V+ 2 15 GND C1- VOLTAGE DOUBLER

4 C2+ 6 -10V

C1- 3 14 T1OUT C2 5 +10V TO -10V V-

C2- VOLTAGE INVERTER C4

C2+ 4 MAX220 13 R1IN +5V

C2- 5 MAX232 R1OUT 400kΩ

MAX232A 12

V- 6 11 T1IN 11 T1IN T1OUT 14

T2OUT T2IN TTL/CMOS +5V RS-232

7 10 400kΩ

INPUTS OUTPUTS

R2IN 8 9 R2OUT 10 T2IN T2OUT 7

DIP/SO 12 R1OUT R1IN 13

CAPACITANCE (μF) TTL/CMOS 5kΩ RS-232

DEVICE C1 C2 C3 C4 C5 OUTPUTS INPUTS

MAX220 0.047 0.33 0.33 0.33 0.33 9 R2OUT R2IN 8

MAX232 1.0 1.0 1.0 1.0 1.0 5kΩ

MAX232A 0.1 0.1 0.1 0.1 0.1

GND

19-4323; Rev 17; 1/15

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Absolute Maximum Ratings—MAX220/222/232A/233A/242/243

(Voltages referenced to GND.) 16-Pin Narrow SO (derate 8.70mW/°C above +70°C) ...696mW

VCC ...........................................................................-0.3V to +6V 16-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW

V+ (Note 1) ..................................................(VCC - 0.3V) to +14V 18-Pin Wide SO (derate 9.52mW/°C above +70°C)......762mW

V- (Note 1) ..............................................................+0.3V to -14V 20-Pin Wide SO (derate 10.00mW/°C above +70°C)....800mW

Input Voltages 20-Pin SSOP (derate 8.00mW/°C above +70°C) ..........640mW

TIN .............................................................-0.3V to (VCC - 0.3V) 16-Pin CERDIP (derate 10.00mW/°C above +70°C).....800mW

RIN (Except MAX220) ........................................................±30V 18-Pin CERDIP (derate 10.53mW/°C above +70°C).....842mW

RIN (MAX220) ....................................................................±25V Operating Temperature Ranges

TOUT (Except MAX220) (Note 2) ......................................±15V MAX2_ _AC_ _, MAX2_ _C_ _ .............................0°C to +70°C

TOUT (MAX220)..............................................................±13.2V MAX2_ _AE_ _, MAX2_ _E_ _ ..........................-40°C to +85°C

Output Voltages MAX2_ _AM_ _, MAX2_ _M_ _ .......................-55°C to +125°C

TOUT..................................................................................±15V Storage Temperature Range .............................-65°C to +160°C

ROUT........................................................-0.3V to (VCC + 0.3V) Lead Temperature (soldering, 10s) .................................+300°C

Driver/Receiver Output Short Circuited to GND.........Continuous Soldering Temperature (reflow)

Continuous Power Dissipation (TA = +70°C) 20 PDIP (P20M+1) .......................................................+225°C

16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW All other lead(Pb)-free packages.................................+260°C

18-Pin Plastic DIP (derate 11.11mW/°C above +70°C)..889mW All other packages containing lead(Pb) ......................+240°C

20-Pin Plastic DIP (derate 8.00mW/°C above +70°C) ..440mW

Note 1: For the MAX220, V+ and V- can have a maximum magnitude of 7V, but their absolute difference cannot exceed 13V.

Note 2: Input voltage measured with TOUT in high-impedance state, VSHDN or VCC = 0V.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics—MAX220/222/232A/233A/242/243

(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA = TMIN to TMAX‚ unless otherwise noted.) (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

RS-232 TRANSMITTERS

Output Voltage Swing All transmitter outputs loaded with 3k to GND ±5 ±8 V

Input Logic-Low Voltage 1.4 0.8 V

Input Logic-High Voltage All devices except MAX220 2 1.4 V

MAX220: VCC = +5.0V 2.4

All except MAX220, normal operation 5 40

Logic Pullup/lnput Current VSHDN = 0V, MAX222/MAX242, shutdown, ±0.01 ±1 μA

MAX220

VCC = +5.5V, VSHDN = 0V, VOUT = ±15V, ±0.01 ±10

MAX222/MAX242

Output Leakage Current VOUT = ±15V ±0.01 ±10 μA

VCC = VSHDN = 0V MAX220, VOUT = ±12V ±25

Data Rate 200 116 kbps

Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V 300 10M

Output Short-Circuit Current VOUT = 0V VOUT = 0V ±7 ±22 mA

MAX220 ±60

RS-232 RECEIVERS

RS-232 Input Voltage Operating Range ±30 V

MAX220 ±25

RS-232 Input Threshold Low VCC = +5V All except MAX243 R2IN 0.8 1.3 V

MAX243 R2IN (Note 4) -3

RS-232 Input Threshold High VCC = +5V All except MAX243 R2IN 1.8 2.4 V

MAX243 R2IN (Note 4) -0.5 -0.1

www.maximintegrated.com Maxim Integrated | 2

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Electrical Characteristics—MAX220/222/232A/233A/242/243 (continued)

(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA = TMIN to TMAX‚ unless otherwise noted.) (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

All except MAX220/MAX243, VCC = +5V, no 0.2 0.5 1.0

hysteresis in shutdown

RS-232 Input Hysteresis MAX220 0.3 V

MAX243 1

RS-232 Input Resistance TA = +25°C (MAX220) 3 5 7 k

3 5 7

TTL/CMOS Output Voltage Low IOUT = 3.2mA 0.2 0.4 V

IOUT = 1.6mA (MAX220) 0.4

TTL/CMOS Output Voltage High IOUT = -1.0mA 3.5 VCC - 0.2 V

TTL/CMOS Output Short-Circuit Current Sourcing VOUT = VGND -2 -10 mA

Sinking VOUT = VCC 10 30

TTL/CMOS Output Leakage Current VSHDN = VCC or VEN = VCC (VSHDN = 0V for ±0.05 ±10 μA

MAX222), 0V VOUT VCC

EN Input Threshold Low MAX242 1.4 0.8 V

EN Input Threshold High MAX242 2.0 1.4 V

Supply Voltage Range 4.5 5.5 V

MAX220 0.5 2

No load MAX222/MAX232A/MAX233A/ 4 10

VCC Supply Current (VSHDN = VCC), MAX242/MAX243 mA

Figures 5, 6, 11, 19 MAX220 12

3k load MAX222/MAX232A/MAX233A/

both inputs MAX242/MAX243 15

TA = +25°C 0.1 10

Shutdown Supply Current MAX222/ TA = 0°C to +70°C 2 50 μA

MAX242 TA = -40°C to +85°C 2 50

TA = -55°C to +125°C 35 100

SHDN Input Leakage Current MAX222/MAX242 ±1 μA

SHDN Threshold Low MAX222/MAX242 1.4 0.8 V

SHDN Threshold High MAX222/MAX242 2.0 1.4 V

CL = 50pF to 2500pF, MAX222/MAX232A/

RL = 3k to 7k, MAX233/MAX242/MAX243 6 12 30

Transition Slew Rate VCC = +5V, TA = V/μs

+25°C, measured

from +3V to -3V or MAX220 1.5 3 30.0

-3V to +3V

MAX222/MAX232A/ 1.3 3.5

tPHLT, Figure 1 MAX233/MAX242/MAX243

Transmitter Propagation Delay TLL to MAX220 4 10 μs

RS-232 (Normal Operation) MAX222/MAX232A/

tPLHT, Figure 1 MAX233/MAX242/MAX243 1.5 3.5

MAX220 5 10

www.maximintegrated.com Maxim Integrated | 3

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Electrical Characteristics—MAX220/222/232A/233A/242/243 (continued)

(VCC = +5V ±10%, C1–C4 = 0.1µF‚ MAX220, C1 = 0.047µF, C2–C4 = 0.33µF, TA = TMIN to TMAX‚ unless otherwise noted.) (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

MAX222/MAX232A/MAX233/ 0.5 1

tPHLR, Figure 2 MAX242/MAX243

Receiver Propagation Delay RS-232 to MAX220 0.6 3 μs

TLL (Normal Operation) MAX222/MAX232A/MAX233/

tPLHR, Figure 2 MAX242/MAX243 0.6 1

MAX220 0.8 3

Receiver Propagation Delay RS-232 to tPHLS, Figure 2 MAX242 0.5 10 μs

TLL (Shutdown) tPHLS, Figure 2 MAX242 2.5 10

Receiver-Output Enable Time tER MAX242, Figure 3 125 500 ns

Receiver-Output Disable Time tDR MAX242, Figure 3 160 500 ns

Transmitter-Output Enable Time MAX222/MAX242, 0.1μF

(SHDN Goes High) tET caps (includes charge-pump 250 μs

start-up), Figure 4

Transmitter-Output Disable Time tDT MAX222/MAX242, 600 ns

(SHDN Goes Low) 0.1μF caps, Figure 4

Transmitter + to - Propagation Delay MAX222/MAX232A/MAX233/ 300

Difference (Normal Operation) tPHLT - tPLHT MAX242/MAX243 ns

MAX220 2000

Receiver + to - Propagation Delay MAX222/MAX232A/MAX233/ 100

Difference (Normal Operation) tPHLR - tPLHR MAX242/MAX243 ns

MAX220 225

Note 3: All units are production tested at hot. Specifications over temperature are guaranteed by design.

Note 4: MAX243 R2OUT is guaranteed to be low when R2IN ≥ 0V or is unconnected.

Typical Operating Characteristics

MAX220/MAX222/MAX232A/MAX233A/MAX242/MAX243

AVAILABLE OUTPUT CURRENT MAX222/MAX242

OUTPUT VOLTAGE vs. LOAD CURRENT vs. DATA RATE ON-TIME EXITING SHUTDOWN

10 1μF MAX220-01 11 MAX220-02 +10V MAX220-03

8 OUTPUT LOAD CURRENT 1μF CAPS V+

EITHER V+ OR V- LOADED 10 FLOWS FROM V+ TO V- V+

6 ALL CAPS +5V 0.1μF CAPS

OUTPUT VOLTAGE (V) 4 VCC = +5V 0.1μF OUTPUT CURRENT (mA) 9 1μF V+, V- VOLTAGE (V) +5V

NO LOAD ON SHDN

2 TRANSMITTER OUTPUTS 8 VCC = +5.25V 0V

0 (EXCEPT MAX220, MAX233A) 0V

V- LOADED, NO LOAD ON V+ 7 ALL CAPS

-2 0.1μF VCC = +4.75V

-4 0.1μF 1μF 1μF CAPS

-6

-8 5 0.1μF CAPS

V+ LOADED, NO LOAD ON V- V- V-

-10 4 -10V

0 5 10 15 20 25 0 10 20 30 40 50 60 500μs/div

LOAD CURRENT (mA) DATA RATE (kb/s)

www.maximintegrated.com Maxim Integrated | 4

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Absolute Maximum Ratings—MAX223/MAX230–MAX241

(Voltages referenced to GND.) 28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W

VCC ...........................................................................-0.3V to +6V 44-Pin Plastic FP (derate 11.11mW/°C above +70°C) .....889mW

V+ ................................................................(VCC - 0.3V) to +14V 14-Pin CERDIP (derate 9.09mW/°C above +70°C) ..........727mW

V- ............................................................................+0.3V to -14V 16-Pin CERDIP (derate 10.00mW/°C above +70°C) ........800mW

Input Voltages 20-Pin CERDIP (derate 11.11mW/°C above +70°C) ........889mW

TIN ............................................................-0.3V to (VCC + 0.3V) 24-Pin Narrow CERDIP

RIN .....................................................................................±30V (derate 12.50mW/°C above +70°C) ..............1W

Output Voltages 24-Pin Sidebraze (derate 20.0mW/°C above +70°C)..........1.6W

TOUT ..................................................(V+ + 0.3V) to (V- - 0.3V) 28-Pin SSOP (derate 9.52mW/°C above +70°C).............762mW

ROUT........................................................-0.3V to (VCC + 0.3V) Operating Temperature Ranges

Short-Circuit Duration, TOUT to GND ........................Continuous MAX2 _ _ C _ _......................................................0°C to +70°C

Continuous Power Dissipation (TA = +70°C) MAX2 _ _ E _ _ ...................................................-40°C to +85°C

14-Pin Plastic DIP (derate 10.00mW/°C above +70°C)....800mW MAX2 _ _ M _ _......................................................-55°C to +125°C

16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)....842mW Storage Temperature Range .............................-65°C to +160°C

20-Pin Plastic DIP (derate 11.11mW/°C above +70°C)....889mW Lead Temperature (soldering, 10s) .................................+300°C

24-Pin Narrow Plastic DIP Soldering Temperature (reflow)

(derate 13.33mW/°C above +70°C) ..........1.07W 20 PDIP (P20M+1) .........................................................+225°C

24-Pin Plastic DIP (derate 9.09mW/°C above +70°C)......500mW 24 PDIP (P24M-1) ..........................................................+225°C

16-Pin Wide SO (derate 9.52mW/°C above +70°C).........762mW All other lead(Pb)-free packages...................................+260°C

20-Pin Wide SO (derate 10.00mW/°C above +70°C).......800mW All other packages containing lead(Pb) ...........................+240°C

24-Pin Wide SO (derate 11.76mW/°C above +70°C).......941mW

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics—MAX223/MAX230–MAX241

(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10%; MAX233/MAX235, VCC = +5V ±5%‚ C1–C4 = 1.0µF;

MAX231/MAX239, VCC = +5V ±10%; V+ = +7.5V to +13.2V; TA = TMIN to TMAX; unless otherwise noted.) (Note 5)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Output Voltage Swing All transmitter outputs loaded with 3kΩ to ground ±5.0 ±7.3 V

MAX232/233 5 10

VCC Supply Current No load, MAX223/230/234–238/240/241 7 15 mA

TA = +25°C

MAX231/239 0.4 1

V+ Supply Current MAX231 1.8 5 mA

MAX239 5 15

Shutdown Supply Current TA = +25°C MAX223 15 50 µA

MAX230/235/236/240/241 1 10

Input Logic-Low Voltage TIN, EN, SHDN (MAX233); EN, SHDN (MAX230/235–241) 0.8 V

TIN 2.0

Input Logic-High Voltage EN, SHDN (MAX223); 2.4 V

EN, SHDN (MAX230/235/236/240/241)

Logic Pullup Current VTIN = 0V 1.5 200 µA

Receiver Input Voltage -30 +30 V

Operating Range

www.maximintegrated.com Maxim Integrated | 5

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Electrical Characteristics—MAX223/MAX230–MAX241 (continued)

(MAX223/230/232/234/236/237/238/240/241, VCC = +5V ±10%; MAX233/MAX235, VCC = +5V ±5%‚ C1–C4 = 1.0µF;

MAX231/MAX239, VCC = +5V ±10%; V+ = +7.5V to +13.2V; TA = TMIN to TMAX; unless otherwise noted.) (Note 5)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Normal operation

VSHDN = +5V (MAX223) 0.8 1.2

RS-232 Input Logic-Low Voltage TA = +25°C, VSHDN = 0V (MAX235/236/240/241) V

VCC = +5V Shutdown (MAX223)

VSHDN = 0V, 0.6 1.5

VEN = +5V (R4IN, R5IN)

Normal operation

VSHDN = 5V (MAX223) 1.7 2.4

RS-232 Input Logic-High Voltage TA = +25°C, VSHDN = 0V (MAX235/236/240/241) V

VCC = +5V Shutdown (MAX223)

VSHDN = 0V, 1.5 2.4

VEN = +5V (R4IN‚ R5IN)

RS-232 Input Hysteresis VCC = +5V, no hysteresis in shutdown 0.2 0.5 1.0 V

RS-232 Input Resistance TA = +25°C, VCC = +5V 3 5 7 kΩ

TTL/CMOS Output Voltage Low IOUT = 1.6mA (MAX231/232/233, IOUT = 3.2mA) 0.4 V

TTL/CMOS Output Voltage High IOUT = -1mA 3.5 VCC - 0.4 V

TTL/CMOS Output Leakage Current 0V ≤ ROUT ≤ VCC; VEN = 0V (MAX223); ±0.05 ±10 µA

VEN = VCC (MAX235–241)

Receiver Output Enable Time Normal MAX223 600 ns

operation MAX235/236/239/240/241 400

Receiver Output Disable Time Normal MAX223 900 ns

operation MAX235/236/239/240/241 250

RS-232 IN to Normal operation 0.5 10

Propagation Delay TTL/CMOS OUT, VSHDN = 0V tPHLS 4 40 µs

CL = 150pF (MAX223) tPLHS 6 40

MAX223/MAX230/MAX234–241, TA = +25°C, VCC = +5V,

RL = 3kΩ to 7kΩ‚ CL = 50pF to 2500pF, measured from 3 5.1 30

+3V to -3V or -3V to +3V

Transition Region Slew Rate V/µs

MAX231/MAX232/MAX233, TA = +25°C, VCC = +5V,

RL = 3kΩ to 7kΩ, CL = 50pF to 2500pF, measured from 4 30

+3V to -3V or -3V to +3V

Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V 300 Ω

Transmitter Output Short-Circuit ±10 mA

Current mA

Note 5: All units are production tested at hot except for the MAX240, which is production tested at TA = +25°C. Specifications over

temperature are guaranteed by design.

www.maximintegrated.com Maxim Integrated | 6

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Typical Operating Characteristics

MAX223/MAX230–MAX241

TRANSMITTER OUTPUT VOLTAGE (VOH)

TRANSMITTER OUTPUT vs. LOAD CAPACITANCE AT TRANSMITTER SLEW RATE

VOLTAGE (VOH) vs. VCC DIFFERENT DATA RATES vs. LOAD CAPACITANCE

8.5 MAX220-04 7.4 MAX220-05 12.0 MAX220-06

2 TRANSMITTERS 1 TRANSMITTER LOADED TA = +25°C

LOADED 7.2 11.0 VCC = +5V

LOADED, RL = 3kΩ

8.0 7.0 10.0 C1–C4 = 1μF

1 TRANSMITTER SLEW RATE (V/μs) 9.0 2 TRANSMITTERS

VOH (V) LOADED VOH (V) 6.8 160kb/s LOADED

7.5 3 TRANS- 80kb/s 8.0

MITTERS 6.6 20kb/s

LOADED 7.0

TA = +25°C 6.4 TA = +25°C 6.0 3 TRANSMITTERS

7.0 C1–C4 = 1μF VCC = +5V LOADED

TRANSMITTER 6.2 3 TRANSMITTERS LOADED 4 TRANSMITTERS

4 TRANSMITTERS LOADS = RL = 3kΩ 5.0 LOADED

LOADED 3kΩ || 2500pF 6.0 C1–C4 = 1μF 4.0

6.5

4.5 5.0 5.5 0 500 1000 1500 2000 2500 0 500 1000 1500 2000 2500

VCC (V) LOAD CAPACITANCE (pF) LOAD CAPACITANCE (pF)

TRANSMITTER OUTPUT VOLTAGE (VOL)

TRANSMITTER OUTPUT vs. LOAD CAPACITANCE AT TRANSMITTER OUTPUT VOLTAGE (V+, V-)

VOLTAGE (VOL) vs. VCC DIFFERENT DATA RATES vs. LOAD CURRENT

-6.0 MAX220-07 -6.0 MAX220-08 10 MAX220-09

4 TRANS- TA = +25°C TA = +25°C

MITTERS C1–C4 = 1μF -6.2 VCC = +5V 8

-6.5 LOADED TRANSMITTER 3 TRANSMITTERS LOADED 6

LOADS = -6.4 RL = 3kΩ TA = +25°C

-7.0 3kΩ || 2500pF C1–C4 = 1μF 4 VCC = +5V

-6.6 C1–C4 = 1μF

VOL (V) VOL (V) V+, V- (V) 2 V+ AND V- V- LOADED,

-7.5 -6.8 160kb/s 0 EQUALLY NO LOAD V+ LOADED,

80kb/s LOADED ON V+ NO LOAD

1 TRANS- -7.0 20kb/s -2 ON V-

-8.0 MITTER -4

LOADED -7.2

-8.5 2 TRANS- 3 TRANS- -6

MITTERS MITTERS -7.4 -8

LOADED LOADED ALL TRANSMITTERS UNLOADED

-9.0 -7.6 -10

4.5 5.0 5.5 0 500 1000 1500 2000 2500 0 5 10 15 20 25 30 35 40 45 50

VCC (V) LOAD CAPACITANCE (pF) CURRENT (mA)

V+, V- WHEN EXITING SHUTDOWN

(1μF CAPACITORS)

MAX220-13

V+

V-

VSHDN*

500ms/div

*SHUTDOWN POLARITY IS REVERSED

FOR NON MAX241 PARTS

www.maximintegrated.com Maxim Integrated | 7

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Absolute Maximum Ratings—MAX225/MAX244–MAX249

(Voltages referenced to GND.) Continuous Power Dissipation (TA = +70°C)

Supply Voltage (VCC) ...............................................-0.3V to +6V 28-Pin Wide SO (derate 12.50mW/°C above +70°C) .............1W

Input Voltages 40-Pin Plastic DIP (derate 11.11mW/°C above +70°C) ...611mW

TIN‚ ENA, ENB, ENR, ENT, ENRA, 44-Pin PLCC (derate 13.33mW/°C above +70°C) ...........1.07W

ENRB, ENTA, ENTB..................................-0.3V to (VCC + 0.3V) Operating Temperature Ranges

RIN .....................................................................................±25V MAX225C_ _, MAX24_C_ _ ..................................0°C to +70°C

TOUT (Note 6)....................................................................±15V MAX225E_ _, MAX24_E_ _ ...............................-40°C to +85°C

ROUT........................................................-0.3V to (VCC + 0.3V) Storage Temperature Range .............................-65°C to +160°C

Short Circuit Duration (one output at a time) Lead Temperature (soldering,10s)) .................................+300°C

TOUT to GND ...........................................................Continuous Soldering Temperature (reflow)

ROUT to GND...........................................................Continuous 40 PDIP (P40M-2) ..........................................................+225°C

All other lead(Pb)-free packages...................................+260°C

All other packages containing lead(Pb) ........................+240°C

Note 6: Input voltage measured with transmitter output in a high-impedance state, shutdown, or VCC = 0V.

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional

operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to

absolute maximum rating conditions for extended periods may affect device reliability.

Electrical Characteristics—MAX225/MAX244–MAX249

(MAX225, VCC = +5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA = TMIN to TMAX; unless

otherwise noted.) (Note 7)

PARAMETER CONDITIONS MIN TYP MAX UNITS

RS-232 TRANSMITTERS

Input Logic-Low Voltage 1.4 0.8 V

Input Logic-High Voltage 2 1.4 V

Logic Pullup/lnput Current Tables 1a–1d Normal operation 10 50 µA

Shutdown ±0.01 ±1

Data Rate Tables 1a–1d, normal operation 120 64 kbps

Output Voltage Swing All transmitter outputs loaded with 3kΩ to GND ±5 ±7.5 V

VENA, VENB, VENT, VENTA, ±0.01 ±25

Output Leakage Current (Shutdown) Tables 1a–1d VENTB = VCC, VOUT = ±15V µA

VCC = 0V, ±0.01 ±25

VOUT = ±15V

Transmitter Output Resistance VCC = V+ = V- = 0V, VOUT = ±2V (Note 8) 300 10M Ω

Output Short-Circuit Current VOUT = 0V ±7 ±30 mA

RS-232 RECEIVERS

RS-232 Input Voltage Operating Range ±25 V

RS-232 Input Logic-Low Voltage VCC = +5V 0.8 1.3 V

RS-232 Input Logic-High Voltage VCC = +5V 1.8 2.4 V

RS-232 Input Hysteresis VCC = +5V 0.2 0.5 1.0 V

RS-232 Input Resistance 3 5 7 kΩ

TTL/CMOS Output Voltage Low IOUT = 3.2mA 0.2 0.4 V

TTL/CMOS Output Voltage High IOUT = -1.0mA 3.5 VCC - 0.2 V

TTL/CMOS Output Short-Circuit Current Sourcing VOUT = VGND -2 -10 mA

Sinking VOUT = VCC 10 30

TTL/CMOS Output Leakage Current Normal operation, outputs disabled, ±0.05 ±0.10 µA

Tables 1a–1d, 0V ≤ VOUT ≤ VCC, VENR_ = VCC

www.maximintegrated.com Maxim Integrated | 8

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Electrical Characteristics—MAX225/MAX244–MAX249 (continued)

(MAX225, VCC = +5.0V ±5%; MAX244–MAX249, VCC = +5.0V ±10%, external capacitors C1–C4 = 1µF; TA = TMIN to TMAX; unless

otherwise noted.) (Note 7)

PARAMETER CONDITIONS MIN TYP MAX UNITS

POWER SUPPLY AND CONTROL LOGIC

Supply Voltage Range MAX225 4.75 5.25 V

MAX244–MAX249 4.5 5.5

No load MAX225 10 20

VCC Supply Current MAX244–MAX249 11 30 mA

(Normal Operation) 3kΩ loads on MAX225 40

all outputs MAX244–MAX249 57

Shutdown Supply Current TA = +25°C 8 25 µA

TA = TMIN to TMAX 50

Leakage current ±1 µA

Control Input Logic-low voltage 1.4 0.8 V

Logic-high voltage 2.4 1.4

AC CHARACTERISTICS

Transition Slew Rate CL = 50pF to 2500pF, RL = 3kΩ to 7kΩ, VCC = +5V, 5 10 30 V/µs

TA = +25°C, measured from +3V to -3V or -3V to +3V

Transmitter Propagation Delay tPHLT, Figure 1 1.3 3.5

TLL to RS-232 (Normal Operation) µs

tPLHT, Figure 1 1.5 3.5

Receiver Propagation Delay tPHLR, Figure 2 0.6 1.5

TLL to RS-232 (Normal Operation) µs

tPLHR, Figure 2 0.6 1.5

Receiver Propagation Delay tPHLS, Figure 2 0.6 10

TLL to RS-232 (Low-Power Mode) µs

tPLHS, Figure 2 3.0 10

Transmitter + to - Propagation tPHLT - tPLHT 350 ns

Delay Difference (Normal Operation)

Receiver + to - Propagation tPHLR - tPLHR 350 ns

Delay Difference (Normal Operation)

Receiver-Output Enable Time tER, Figure 3 100 500 ns

Receiver-Output Disable Time tDR, Figure 3 100 500 ns

MAX246–MAX249 5 µs

(excludes charge-pump startup)

Transmitter Enable Time tET

MAX225/MAX245–MAX249 10 ms

(includes charge-pump startup)

Transmitter Disable Time tDT, Figure 4 100 ns

Note 7: All units production tested at hot. Specifications over temperature are guaranteed by design.

Note 8: The 300Ω minimum specification complies with EIA/TIA-232E, but the actual resistance when in shutdown mode or VCC =

0V is 10MΩ as is implied by the leakage specification.

www.maximintegrated.com Maxim Integrated | 9

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Typical Operating Characteristics

MAX225/MAX244–MAX249

TRANSMITTER OUTPUT VOLTAGE (V+, V-)

TRANSMITTER SLEW RATE OUTPUT VOLTAGE vs. LOAD CAPACITANCE AT

vs. LOAD CAPACITANCE vs. LOAD CURRENT FOR V+ AND V- DIFFERENT DATA RATES

18 MAX220-10 10 MAX220-11 9.0 VCC = +5V WITH ALL TRANSMITTERS DRIVEN MAX220-12

VCC = +5V 8 8.5 LOADED WITH 5kΩ

TRANSMITTER SLEW RATE (V/μs) 16 V+ AND V- LOADED 10kb/s

14 6 EITHER V+ OR 8.0 20kb/s

EXTERNAL POWER SUPPLY OUTPUT VOLTAGE (V) 4 VCC = +5V V- LOADED

12 1μF CAPACITORS 2 EXTERNAL CHARGE PUMP V+, V- (V) 7.5 40kb/s

1μF CAPACITORS

10 0 8 TRANSMITTERS 7.0 60kb/s

40kb/s DATA RATE -2 DRIVING 5kΩ AND

8 8 TRANSMITTERS 2000pF AT 20kb/s 6.5

LOADED WITH 3kΩ -4 V- LOADED

6 6.0 100kb/s

-6 V+ AND V- LOADED 200kb/s

4 -8 5.5

V+ LOADED 5.0 ALL CAPACITIORS 1μF

2 -10

0 1 2 3 4 5 0 5 10 15 20 25 30 35 0 1 2 3 4 5

LOAD CAPACITANCE (nF) LOAD CURRENT (mA) LOAD CAPACITANCE (nF)

www.maximintegrated.com Maxim Integrated | 10

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Test Circuits/Timing Diagrams

+3V

0V* 50% 50%

+3V INPUT

INPUT 0V

OUTPUT VCC

50% 50%

V+ GND

OUTPUT 0V

V- tPHLR tPLHR

tPHLS tPLHS

tPLHT tPHLT

*EXCEPT FOR R2 ON THE MAX243

WHERE -3V IS USED.

Figure 1. Transmitter Propagation-Delay Timing Figure 2. Receiver Propagation-Delay Timing

RX OUT 1kΩ

RX IN RX VCC - 2V +3V

SHDN

a) TEST CIRCUIT 0V

150pF

+3V OUTPUT DISABLE TIME (tDT)

EN INPUT V+

0V EN +5V

OUTPUT ENABLE TIME (tER) 0V

+3.5V -5V

RECEIVER V-

OUTPUTS

+0.8V

a) TIMING DIAGRAM

b) ENABLE TIMING

+3V EN

EN INPUT 0V 1 OR 0 TX

OUTPUT DISABLE TIME (tDR) 3kΩ 50pF

VOH VOH - 0.5V

RECEIVER VCC - 2V

OUTPUTS

VOL VOL + 0.5V b) TEST CIRCUIT

c) DISABLE TIMING

Figure 3. Receiver-Output Enable and Disable Timing Figure 4. Transmitter-Output Disable Timing

www.maximintegrated.com Maxim Integrated | 11

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Control Pin Configuration Tables

Table 1a. MAX245 Control Pin Configurations

ENT ENR OPERATION STATUS TRANSMITTERS RECEIVERS

0 0 Normal Operation All Active All Active

0 1 Normal Operation All Active All High-Z

1 0 Shutdown All High-Z All Low-Power Receive Mode

1 1 Shutdown All High-Z All High-Z

Table 1b. MAX245 Control Pin Configurations

ENT ENR OPERATION TRANSMITTERS RECEIVERS

STATUS TA1–TA4 TB1–TB4 RA1–RA5 RB1–RB5

0 0 Normal Operation All Active All Active All Active All Active

0 1 Normal Operation All Active All Active RA1–RA4 High-Z, RB1–RB4 High-Z,

RA5 Active RB5 Active

1 0 Shutdown All High-Z All High-Z All Low-Power All Low-Power

Receive Mode Receive Mode

RA1–RA4 High-Z, RB1–RB4 High-Z,

1 1 Shutdown All High-Z All High-Z RA5 Low-Power RB5 Low-Power

Receive Mode Receive Mode

Table 1c. MAX246 Control Pin Configurations

ENA ENB OPERATION TRANSMITTERS RECEIVERS

STATUS TA1–TA4 TB1–TB4 RA1–RA5 RB1–RB5

0 0 Normal Operation All Active All Active All Active All Active

0 1 Normal Operation All Active All High-Z All Active RB1–RB4 High-Z,

RB5 Active

1 0 Shutdown All High-Z All Active RA1–RA4 High-Z, All Active

RA5 Active

RA1–RA4 High-Z, RB1–RB4 High-Z,

1 1 Shutdown All High-Z All High-Z RA5 Low-Power RA5 Low-Power

Receive Mode Receive Mode

www.maximintegrated.com Maxim Integrated | 12

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Table 1d. MAX247/MAX248/MAX249 Control Pin Configurations

TRANSMITTERS RECEIVERS

ENTA ENTB ENRA ENRB OPERATION MAX247 TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB5

STATUS MAX248 TA1–TA4 TB1–TB4 RA1–RA4 RB1–RB4

MAX249 TA1–TA3 TB1–TB3 RA1–RA5 RB1–RB5

0 0 0 0 Normal Operation All Active All Active All Active All Active

All High-Z, except

0 0 0 1 Normal Operation All Active All Active All Active RB5 stays active on

MAX247

0 0 1 0 Normal Operation All Active All Active All High-Z All Active

All High-Z, except

0 0 1 1 Normal Operation All Active All Active All High-Z RB5 stays active on

MAX247

0 1 0 0 Normal Operation All Active All High-Z All Active All Active

All High-Z, except

0 1 0 1 Normal Operation All Active All High-Z All Active RB5 stays active on

MAX247

0 1 1 0 Normal Operation All Active All High-Z All High-Z All Active

All High-Z, except

0 1 1 1 Normal Operation All Active All High-Z All High-Z RB5 stays active on

MAX247

1 0 0 0 Normal Operation All High-Z All Active All Active All Active

All High-Z, except

1 0 0 1 Normal Operation All High-Z All Active All Active RB5 stays active on

MAX247

1 0 1 0 Normal Operation All High-Z All Active All High-Z All Active

All High-Z, except

1 0 1 1 Normal Operation All High-Z All Active All High-Z RB5 stays active on

MAX247

1 1 0 0 Shutdown All High-Z All High-Z Low-Power Low-Power

Receive Mode Receive Mode

Low-Power All High-Z, except

1 1 0 1 Shutdown All High-Z All High-Z Receive Mode RB5 stays active on

MAX247

1 1 1 0 Shutdown All High-Z All High-Z All High-Z Low-Power

Receive Mode

All High-Z, except

1 1 1 1 Shutdown All High-Z All High-Z All High-Z RB5 stays active on

MAX247

www.maximintegrated.com Maxim Integrated | 13

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Detailed Description mode, in three-state mode, or when device power is

The MAX220–MAX249 contain four sections: dual removed. Outputs can be driven to ±15V. The power-

charge-pump DC-DC voltage converters, RS-232 dri- supply current typically drops to 8µA in shutdown mode.

vers, RS-232 receivers, and receiver and transmitter The MAX220 does not have pullup resistors to force the

enable control inputs. outputs of the unused drivers low. Connect unused

inputs to GND or VCC.

Dual Charge-Pump Voltage Converter The MAX239 has a receiver three-state control line, and

The MAX220–MAX249 have two internal charge-pumps the MAX223, MAX225, MAX235, MAX236, MAX240,

that convert +5V to ±10V (unloaded) for RS-232 driver and MAX241 have both a receiver three-state control

operation. The first converter uses capacitor C1 to dou- line and a low-power shutdown control. Table 2 shows

ble the +5V input to +10V on C3 at the V+ output. The the effects of the shutdown control and receiver three-

second converter uses capacitor C2 to invert +10V to state control on the receiver outputs.

-10V on C4 at the V- output. The receiver TTL/CMOS outputs are in a high-imped-

A small amount of power may be drawn from the +10V ance, three-state mode whenever the three-state enable

(V+) and -10V (V-) outputs to power external circuitry line is high (for the MAX225/MAX235/MAX236/MAX239–

(see the Typical Operating Characteristics section), MAX241), and are also high-impedance whenever the

except on the MAX225 and MAX245–MAX247, where shutdown control line is high.

these pins are not available. V+ and V- are not regulated, When in low-power shutdown mode, the driver outputs

so the output voltage drops with increasing load current. are turned off and their leakage current is less than 1µA

Do not load V+ and V- to a point that violates the mini- with the driver output pulled to ground. The driver output

mum ±5V EIA/TIA-232E driver output voltage when leakage remains less than 1µA, even if the transmitter

sourcing current from V+ and V- to external circuitry. output is backdriven between 0V and (VCC + 6V). Below

When using the shutdown feature in the MAX222, -0.5V, the transmitter is diode clamped to ground with

MAX225, MAX230, MAX235, MAX236, MAX240, 1kΩ series impedance. The transmitter is also zener

MAX241, and MAX245–MAX249, avoid using V+ and V- clamped to approximately VCC + 6V, with a series

to power external circuitry. When these parts are shut impedance of 1kΩ.

down, V- falls to 0V, and V+ falls to +5V. For applica- The driver output slew rate is limited to less than 30V/µs

tions where a +10V external supply is applied to the V+ as required by the EIA/TIA-232E and V.28 specifica-

pin (instead of using the internal charge pump to gen- tions. Typical slew rates are 24V/µs unloaded and

erate +10V), the C1 capacitor must not be installed and 10V/µs loaded with 3Ω and 2500pF.

the SHDN pin must be connected to VCC. This is

because V+ is internally connected to VCC in shutdown RS-232 Receivers

mode. EIA/TIA-232E and V.28 specifications define a voltage

RS-232 Drivers level greater than 3V as a logic 0, so all receivers invert.

The typical driver output voltage swing is ±8V when Input thresholds are set at 0.8V and 2.4V, so receivers

loaded with a nominal 5kΩ RS-232 receiver and VCC = respond to TTL level inputs as well as EIA/TIA-232E and

+5V. Output swing is guaranteed to meet the EIA/TIA- V.28 levels.

232E and V.28 specification, which calls for ±5V mini-

mum driver output levels under worst-case conditions. Table 2. Three-State Control of

These include a minimum 3kΩ load, VCC = +4.5V, and Receivers

maximum operating temperature. Unloaded driver out-

put voltage ranges from (V+ -1.3V) to (V- +0.5V). PART SHDN SHDN EN EN(R) RECEIVERS

Input thresholds are both TTL and CMOS compatible. Low X High Impedance

The inputs of unused drivers can be left unconnected MAX223 __ High Low __ Active

since 400kΩ input pullup resistors to VCC are built in High High High Impedance

(except for the MAX220). The pullup resistors force the

outputs of unused drivers low because all drivers invert. MAX225 __ __ __ Low High Impedance

The internal input pullup resistors typically source 12µA, High Active

except in shutdown mode where the pullups are dis- MAX235 Low Low High Impedance

abled. Driver outputs turn off and enter a high-imped- MAX236 Low __ __ High Active

ance state—where leakage current is typically MAX240 High X High Impedance

microamperes (maximum 25µA)—when in shutdown

www.maximintegrated.com Maxim Integrated | 14

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

The receiver inputs withstand an input overvoltage up Shutdown—MAX222–MAX242

to ±25V and provide input terminating resistors with On the MAX222‚ MAX235‚ MAX236‚ MAX240‚ and

nominal 5kΩ values. The receivers implement Type 1 MAX241‚ all receivers are disabled during shutdown.

interpretation of the fault conditions of V.28 and On the MAX223 and MAX242‚ two receivers continue to

EIA/TIA-232E. operate in a reduced power mode when the chip is in

The receiver input hysteresis is typically 0.5V with a shutdown. Under these conditions‚ the propagation

guaranteed minimum of 0.2V. This produces clear out- delay increases to about 2.5µs for a high-to-low input

put transitions with slow-moving input signals, even transition. When in shutdown, the receiver acts as a

with moderate amounts of noise and ringing. The CMOS inverter with no hysteresis. The MAX223 and

receiver propagation delay is typically 600ns and is MAX242 also have a receiver output enable input (EN

independent of input swing direction. for the MAX242 and EN for the MAX223) that allows

receiver output control independent of SHDN (SHDN

Low-Power Receive Mode for MAX241). With all other devices‚ SHDN (SHDN for

The low-power receive mode feature of the MAX223, MAX241) also disables the receiver outputs.

MAX242, and MAX245–MAX249 puts the IC into shut- The MAX225 provides five transmitters and five

down mode but still allows it to receive information. This receivers‚ while the MAX245 provides ten receivers and

is important for applications where systems are periodi- eight transmitters. Both devices have separate receiver

cally awakened to look for activity. Using low-power and transmitter-enable controls. The charge pumps

receive mode, the system can still receive a signal that turn off and the devices shut down when a logic high is

will activate it on command and prepare it for communi- applied to the ENT input. In this state, the supply cur-

cation at faster data rates. This operation conserves rent drops to less than 25µA and the receivers continue

system power. to operate in a low-power receive mode. Driver outputs

Negative Threshold—MAX243 enter a high-impedance state (three-state mode). On

The MAX243 is pin compatible with the MAX232A, differ- the MAX225‚ all five receivers are controlled by the

ing only in that RS-232 cable fault protection is removed ENR input. On the MAX245‚ eight of the receiver out-

on one of the two receiver inputs. This means that control puts are controlled by the ENR input‚ while the remain-

lines such as CTS and RTS can either be driven or left ing two receivers (RA5 and RB5) are always active.

unconnected without interrupting communication. RA1–RA4 and RB1–RB4 are put in a three-state mode

Different cables are not needed to interface with different when ENR is a logic high.

pieces of equipment. Receiver and Transmitter Enable

The input threshold of the receiver without cable fault Control Inputs

protection is -0.8V rather than +1.4V. Its output goes The MAX225 and MAX245–MAX249 feature transmitter

positive only if the input is connected to a control line and receiver enable controls.

that is actively driven negative. If not driven, it defaults The receivers have three modes of operation: full-speed

to the 0 or “OK to send” state. Normally‚ the MAX243’s receive (normal active)‚ three-state (disabled)‚ and low-

other receiver (+1.4V threshold) is used for the data line power receive (enabled receivers continue to function

(TD or RD)‚ while the negative threshold receiver is con- at lower data rates). The receiver enable inputs control

nected to the control line (DTR‚ DTS‚ CTS‚ RTS, etc.). the full-speed receive and three-state modes. The

Other members of the RS-232 family implement the transmitters have two modes of operation: full-speed

optional cable fault protection as specified by EIA/TIA- transmit (normal active) and three-state (disabled). The

232E specifications. This means a receiver output goes transmitter enable inputs also control the shutdown

high whenever its input is driven negative‚ left uncon- mode. The device enters shutdown mode when all

nected‚ or shorted to ground. The high output tells the transmitters are disabled. Enabled receivers function in

serial communications IC to stop sending data. To the low-power receive mode when in shutdown.

avoid this‚ the control lines must either be driven or

connected with jumpers to an appropriate positive volt-

age level.

www.maximintegrated.com Maxim Integrated | 15

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Tables 1a–1d define the control states. The MAX244 The MAX249 provides ten receivers and six drivers with

has no control pins and is not included in these tables. four control pins. The ENRA and ENRB receiver enable

The MAX246 has ten receivers and eight drivers with inputs each control five receiver outputs. The ENTA

two control pins, each controlling one side of the and ENTB transmitter enable inputs control three dri-

device. A logic high at the A-side control input (ENA) vers each. There is no always-active receiver. The

causes the four A-side receivers and drivers to go into device enters shutdown mode and transmitters go into

a three-state mode. Similarly, the B-side control input a three-state mode with a logic high on both ENTA and

(ENB) causes the four B-side drivers and receivers to ENTB. In shutdown mode, active receivers operate in a

go into a three-state mode. As in the MAX245, one A- low-power receive mode at data rates up to 20kb/s.

side and one B-side receiver (RA5 and RB5) remain Applications Information

active at all times. The entire device is put into shut- Figures 5 through 25 show pin configurations and typi-

down mode when both the A and B sides are disabled cal operating circuits. In applications that are sensitive

(ENA = ENB = +5V).

The MAX247 provides nine receivers and eight drivers to power-supply noise, VCC should be decoupled to

with four control pins. The ENRA and ENRB receiver ground with a capacitor of the same value as C1 and

enable inputs each control four receiver outputs. The C2 connected as close as possible to the device.

ENTA and ENTB transmitter enable inputs each control

four drivers. The ninth receiver (RB5) is always active.

The device enters shutdown mode with a logic high on

both ENTA and ENTB.

The MAX248 provides eight receivers and eight drivers

with four control pins. The ENRA and ENRB receiver

enable inputs each control four receiver outputs. The

ENTA and ENTB transmitter enable inputs control four

drivers each. This part does not have an always-active

receiver. The device enters shutdown mode and trans-

mitters go into a three-state mode with a logic high on

both ENTA and ENTB.

www.maximintegrated.com Maxim Integrated | 16

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V INPUT C3

TOP VIEW

+ 16

C1+ 1 16 VCC 1 C1+ VCC V+ 2 +10V

C1 3 +5V TO +10V

V+ 2 15 GND C1- VOLTAGE DOUBLER

4 C2+ 6 -10V

C1- 3 14 T1OUT C2 5 +10V TO -10V V-

C2- VOLTAGE INVERTER C4

C2+ 4 MAX220 13 R1IN +5V

C2- 5 MAX232 R1OUT 400kΩ

MAX232A 12

V- 6 11 T1IN 11 T1IN T1OUT 14

T2OUT T2IN TTL/CMOS +5V RS-232

7 10 400kΩ

INPUTS OUTPUTS

R2IN 8 9 R2OUT 10 T2IN T2OUT 7

DIP/SO 12 R1OUT R1IN 13

CAPACITANCE (μF) TTL/CMOS 5kΩ RS-232

DEVICE C1 C2 C3 C4 C5 OUTPUTS INPUTS

MAX220 0.047 0.33 0.33 0.33 0.33 9 R2OUT R2IN 8

MAX232 1.0 1.0 1.0 1.0 1.0 5kΩ

MAX232A 0.1 0.1 0.1 0.1 0.1

GND

Figure 5. MAX220/MAX232/MAX232A Pin Configuration and Typical Operating Circuit

TOP VIEW +5V INPUT C3 ALL CAPACITORS = 0.1μF

2 C1+ VCC 3 +10V

+ C1 4 +5V TO +10V V+

(N.C.) EN 1 20 SHDN C1- VOLTAGE DOUBLER

+ 5 C2+ 7 -10V

(N.C.) EN 1 18 SHDN C1+ 2 19 VCC C2 +10V TO -10V V-

6 C2- VOLTAGE INVERTER C4

C1+ 2 17 VCC V+ 3 18 GND

V+ 3 16 GND C1- 4 17 T1OUT +5V

400kΩ (EXCEPT MAX220)

C1- 4 15 T1OUT C2+ 5 MAX222 16 N.C. 12 T1IN T1OUT 15

MAX222 MAX242

C2+ 5 MAX242 14 R1IN C2- 6 15 R1IN +5V

TTL/CMOS 400kΩ (EXCEPT MAX220) RS-232

C2- 6 13 R1OUT V- 7 14 R1OUT INPUTS OUTPUTS

V- T2OUT 11 T2IN T2OUT 8

7 12 T1IN 8 13 N.C.

T2OUT 8 11 T2IN R2IN 9 12 T1IN 13 R1OUT R1IN 14

R2IN 9 10 R2OUT R2OUT 10 11 T2IN

TTL/CMOS 5kΩ RS-232

OUTPUTS INPUTS

DIP/SO SSOP 10 R2OUT R2IN 9

1 (N.C.) EN 5kΩ

( ) ARE FOR MAX222 ONLY. SHDN 18

PIN NUMBERS IN TYPICAL OPERATING CIRCUIT ARE FOR DIP/SO PACKAGES ONLY. GND

Figure 6. MAX222/MAX242 Pin Configurations and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 17

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V

TOP VIEW 0.1μF

28 27

+5V VCC VCC

400kΩ

+ 3 T1IN 11

ENR 1 28 VCC +5V T1OUT

ENR 2 27 VCC 400kΩ

4 T2IN 12

T1IN 3 26 ENT T2OUT

+5V

T2IN 4 25 T3IN 400kΩ

R1OUT 5 MAX225 24 T4IN 25 T3IN 18

R2OUT 6 23 T5IN +5V T3OUT

R3OUT 7 22 R4OUT 400kΩ

24 T4IN 17

R3IN 8 21 R5OUT +5V T4OUT

R2IN 9 20 R5IN 400kΩ

R1IN R4IN T5IN T5OUT

10 19 23 16

T1OUT 11 18 T3OUT ENT

T2OUT 26 T5OUT 15

12 17 T4OUT

GND 13 16 T5OUT 5 R1OUT R1IN 10

GND 14 15 T5OUT 5kΩ

SO 6 R2OUT R2IN 9

5kΩ

7 R3OUT R3IN 8

MAX225 FUNCTIONAL DESCRIPTION

5 RECEIVERS 5kΩ

5 TRANSMITTERS R4OUT R4IN

2 CONTROL PINS 22 19

1 RECEIVER ENABLE (ENR) 5kΩ

1 TRANSMITTER ENABLE (ENT) R5OUT R5IN

21 20

5kΩ

1 ENR

PINS (ENR, GND, VCC, T5OUT) ARE INTERNALLY CONNECTED. 2 ENR GND GND

CONNECT EITHER OR BOTH EXTERNALLY. T5OUT IS A SINGLE DRIVER. 13 14

Figure 7. MAX225 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 18

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +5V INPUT

1.0μF

12 11 1.0μF

C1+ VCC 13

1.0μF 14 +5V TO +10V V+

15 C1- VOLTAGE DOUBLER

C2+ +10V TO -10V 17

1.0μF 16 VOLTAGE INVERTER V-

C2- 1.0μF

+5V

400kΩ

7 T1IN T1 T1OUT 2

T3OUT 1 28 T4OUT +5V

T1OUT 2 27 R3IN 400kΩ

T2OUT 3 26 R3OUT 6 T2IN T2 T2OUT 3

R2IN 4 25 SHDN (SHDN) +5V

TTL/CMOS 400kΩ RS-232

R2OUT 5 24 EN (EN) INPUTS OUTPUTS

T2IN 6 MAX223 23 R4IN* 20 T3IN T3 T3OUT 1

MAX241

T1IN 7 22 R4OUT* +5V

R1OUT 8 21 T4IN 400kΩ

R1IN 9 20 T3IN 21 T4IN T4 T4OUT 28

GND 10 19 R5OUT*

VCC 11 18 R5IN* 8 R1OUT R1 R1IN 9

C1+ 12 17 V- 5kΩ

V+ 13 16 C2- 5 R2OUT R2IN 4

C1- 14 15 C2+ R2

5kΩ

Wide SO/

SSOP LOGIC 26 R3OUT R3IN 27 RS-232

OUTPUTS R3 INPUTS

5kΩ

22 R4OUT R4 R4IN 23

5kΩ

19 R5OUT R5 R5IN 18

*R4 AND R5 IN MAX223 REMAIN ACTIVE IN SHUTDOWN. 5kΩ

NOTE: PIN LABELS IN ( ) ARE FOR MAX241. 24 EN (EN) SHDN 25

GND (SHDN)

Figure 8. MAX223/MAX241 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 19

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V INPUT

TOP VIEW 1.0μF

7 1.0μF

8 C1+ VCC V+ 9

1.0μF 10 C1- +5V TO +10V

+ VOLTAGE DOUBLER

T3OUT 1 20 T4OUT 11 C2+ +10V TO -10V

1.0μF 12 VOLTAGE INVERTER V- 13

T1OUT 2 19 T5IN C2- 1.0μF

T2OUT 3 18 N.C. +5V

T2IN 400kΩ

4 17 SHDN 5 T1IN T1OUT 2

T1IN MAX230 T1

5 16 T5OUT +5V

GND 15 T4IN 400kΩ

6 4 T2IN T2OUT 3

VCC T2

7 14 T3IN +5V

C1+ 8 13 V- 400kΩ

TTL/CMOS 14 T3IN T3 T3OUT 1 RS-232

V+ 9 12 C2- INPUTS +5V OUTPUTS

C1- C2+ 400kΩ

10 11 15 T4IN T4OUT 20

+5V T4

DIP/SO 400kΩ

19 T5IN T5 T5OUT 16

N.C.x 18 GND 17 SHDN

Figure 9. MAX230 Pin Configuration and Typical Operating Circuit

+5V INPUT

TOP VIEW 1.0μF +7.5V TO +12V

13 (15)

1 C1+ VCC V+ 14 (16)

1.0μF 2 +12V TO -12V V- 3

C1- VOLTAGE CONVERTER C2

+ C+ + V+ +5V 1.0μF

C+ 1 14 V+ 1 16

(10) 400kΩ (13)

C- 2 13 VCC C- 2 15 VCC T1IN T1OUT 11

8 T1

V- 3 12 GND V- 3 14 GND +5V

T2OUT 4 MAX231 11 T1OUT T2OUT 4 MAX231 13 T1OUT TTL/CMOS RS-232

INPUTS 400kΩ OUTPUTS

R2IN 5 10 R1IN R2IN 5 12 R1IN 7 T2IN T2OUT 4

R2OUT 6 9 R1OUT R2OUT 6 11 R1OUT (11) 9 (12)

T2IN T1IN R1OUT R1 R1IN 10

T2IN 7 8 T1IN 7 10

N.C. 8 9 N.C. TTL/CMOS 5kΩ RS-232

DIP OUTPUTS INPUTS

SO 6 R2OUT R2 R2IN 5

5kΩ

GND

PIN NUMBERS IN ( ) ARE FOR SO PACKAGE. 12 (14)

Figure 10. MAX231 Pin Configurations and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 20

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V INPUT

1.0μF

TOP VIEW 7

+5V VCC

400kΩ

T2IN + R2OUT 2 T1IN T1OUT 5

1 20

T1IN R2IN TTL/CMOS +5V

2 19 400kΩ RS-232

R1OUT INPUTS OUTPUTS

3 18 T2OUT 1 T2IN T2OUT 18

R1IN 4 17 V- R1OUT 4

3 R1IN

T1OUT 5 MAX233 16 C2-

MAX233A 5kΩ

GND 6 15 C2+ TTL/CMOS RS-232

VCC OUTPUTS INPUTS

7 14 V+ (C1-)

(V+) C1+ 8 13 C1- (C1+) 20 R2OUT R2IN 19

GND 9 12 V- (C2+) DO NOT MAKE 8 (13) C1+ 5kΩ C2+ 11 (12)

(V-) CS- 10 11 C2+ (C2-) CONNECTIONS TO 13 (14) C1- 15

THESE PINS 12 (10) C2+ 16

INTERNAL -10V V- C2-

DIP/SO POWER SUPPLY 17 V- CS- 10 (11)

INTERNAL +10V 14 (8) V+ GND GND

POWER SUPPLY 6 9

PIN NAMES IN ( ) ARE FOR SO PACKAGE.

Figure 11. MAX233/MAX233A Pin Configuration and Typical Operating Circuit

+5V INPUT

TOP VIEW 1.0μF

7 6 1.0μF

C1+ VCC 8

1.0μF 9 +5V TO +10V V+

C1- VOLTAGE DOUBLER

10 C2+ +10V TO -10V

V- 12

+ 1.0μF 11 C2- VOLTAGE INVERTER 1.0μF

T1OUT 1 16 T3OUT

T2OUT T4OUT +5V

2 15 400kΩ

T2IN 3 14 T4IN 4 T1IN T1OUT 1

MAX234 T1

T1IN 4 13 T3IN +5V

GND 5 12 V- 400kΩ

VCC 6 11 C2- 3 T2IN T2 T2OUT 2

C1+ 7 10 C2+ TTL/CMOS +5V RS-232

INPUTS 400kΩ OUTPUTS

V+ 8 9 C1-

13 T3IN T3 T3OUT 16

DIP/SO +5V

400kΩ

14 T4IN T4 T4OUT 15

GND

Figure 12. MAX234 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 21

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V INPUT

TOP VIEW 1.0μF

+5V VCC

400kΩ

8 T1IN T1 T1OUT 3

+5V

400kΩ

7 T2IN T2 T2OUT 4

+5V

400kΩ

TTL/CMOS 15 T3IN T3 T3OUT 2 RS-232

+ INPUTS OUTPUTS

T4OUT 1 24 R3IN +5V

400kΩ

T3OUT 2 23 R3OUT 16 T4IN T4OUT 1

T1OUT 3 22 T5IN

T2OUT 4 21 SHDN +5V

400kΩ

R2IN 5 MAX235 20 EN 22 T5IN T5OUT 19

R2OUT 6 19 T5OUT

T2IN 7 18 R4IN 9 R1OUT R1IN 10

T1IN 8 17 R4OUT T1

R1OUT 9 16 T4IN 5kΩ

R1IN 10 15 T3IN 6 R2OUT R2IN 5

GND 11 14 R5OUT R2

VCC 12 13 R5IN 5kΩ

DIP TTL/CMOS 23 R3OUT R3 R3IN 24 RS-232

OUTPUTS INPUTS

5kΩ

17 R4OUT R4 R4IN 18

5kΩ

14 R5OUT R5 R5IN 13

20 EN 5kΩ

SHDN 21

GND

Figure 13. MAX235 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 22

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +5V INPUT

1.0μF

9 1.0μF

10 C1+ VCC 11

V+

1.0μF 12 +5V TO +10V

C1- VOLTAGE DOUBLER

13 C2+ V- 15

1.0μF 14 +10V TO -10V 1.0μF

C2- VOLTAGE INVERTER

+5V

400kΩ

7 T1IN T1 T1OUT 2

T3OUT 1 + 24 T4OUT

+5V

T1OUT 2 23 R2IN 400kΩ

6 T2IN T2 T2OUT 3

T2OUT 3 22 R2OUT

R1IN 4 21 SHDN TTL/CMOS +5V RS-232

MAX236 INPUTS 400kΩ OUTPUTS

R1OUT 5 20 EN

18 T3IN T3 T3OUT 1

T2IN 6 19 T4IN

T1IN 7 18 T3IN +5V

GND 8 17 R3OUT 400kΩ

19 T4IN T4 T4OUT 24

VCC 9 16 R3IN

C1+ 10 15 V-

V+ 11 14 C2- 5 R1OUT R1IN 4

C1- 12 13 C2+

5kΩ

DIP/SO

TTL/CMOS 22 R2OUT R2 R2IN 23 RS-232

OUTPUTS INPUTS

5kΩ

17 R3OUT R3 R3IN 16

5kΩ

20 EN SHDN 21

GND

Figure 14. MAX236 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 23

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW

+5V INPUT

1.0μF

9 1.0μF

10 C1+ VCC 11

+5V TO +10V V+

1.0μF 12 C1- VOLTAGE DOUBLER

13 C2+ V- 15

1.0μF +10V TO -10V 1.0μF

14 C2- VOLTAGE INVERTER

+5V

+ 400kΩ

T3OUT 1 24 T4OUT 7 T1IN T1 T1OUT 2

T1OUT 2 23 R2IN +5V

T2OUT 3 22 R2OUT 400kΩ

6 T2IN T2 T2OUT 3

R1IN 4 21 T5IN +5V

R1OUT 5 MAX237 20 T5OUT 400kΩ

T2IN 6 19 T4IN TTL/CMOS 18 T3IN T3OUT 1 RS-232

INPUTS +5V T3 OUTPUTS

T1IN 7 18 T3IN

GND 8 17 R3OUT 400kΩ

VCC 9 16 R3IN 19 T4IN T4 T4OUT 24

+5V

C1+ 10 15 V- 400kΩ

V+ 11 14 C2- 21 T5IN T5OUT 20

C1- 12 13 C2+ T5

DIP/SO 5 R1OUT R1IN 4

5kΩ

TTL/CMOS 22 R2OUT R2 R2IN 23 RS-232

OUTPUTS INPUTS

5kΩ

17 R3OUT R3 R3IN 16

5kΩ

GND

Figure 15. MAX237 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 24

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW

+5V INPUT

1.0μF

9 1.0μF

10 C1+ VCC V+ 11

1.0μF 12 +5V TO +10V

C1- VOLTAGE DOUBLER

13 C2+

+10V TO -10V V- 15

1.0μF 14 VOLTAGE INVERTER

C2- 1.0μF

+5V

400kΩ

T2OUT 1 + 24 T3OUT 5 T1IN T1OUT 2

T1OUT 2 23 R3IN +5V

400kΩ

R2IN 3 22 R3OUT

R2OUT 4 21 T4IN 18 T2IN T2 T2OUT 1

MAX238 TTL/CMOS +5V RS-232

T1IN 5 20 T4OUT INPUTS 400kΩ OUTPUTS

R1OUT 6 19 T3IN 19 T3IN T3OUT 24

R1IN 7 18 T2IN T3

+5V

GND 8 17 R4OUT 400kΩ

VCC 9 16 R4IN 21 T4IN T4 T4OUT 20

C1+ 10 15 V-

V+ 11 14 C2-

C1- 12 13 C2+ 6 R1OUT R1 R1IN 7

DIP/SO 5kΩ

4 R2OUT R2 R2IN 3

TTL/CMOS 5kΩ RS-232

OUTPUTS INPUTS

22 R3OUT R3 R3IN 23

5kΩ

17 R4OUT R4 R4IN 16

5kΩ

GND

Figure 16. MAX238 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 25

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +7.5V TO +13.2V

+5V INPUT INPUT

1.0μF

4 5

6 C1+ VCC V+ 8

+10V TO -10V V-

1.0μF 7 C1- VOLTAGE INVERTER 1.0μF

+5V

400kΩ

24 T1IN T1 T1OUT 19

R1OUT 1 + 24 T1IN +5V

400kΩ

R1IN 2 23 T2IN

TTL/CMOS 23 T2IN T2 T2OUT 20 RS-232

GND 3 22 R2OUT INPUTS OUTPUTS

VCC 4 21 R2IN +5V

MAX239 400kΩ

V+ 5 20 T2OUT

16 T3IN T3 T3OUT 13

C+ 6 19 T1OUT

C- 7 18 R3IN

V- 8 17 R3OUT 1 R1OUT R1IN 2

R5IN 9 16 T3IN

5kΩ

R5OUT 10 15 N.C.

R4OUT 11 14 EN 22 R2OUT R2 R2IN 21

R4IN 12 13 T3OUT

5kΩ

DIP/SO 17

TTL/CMOS R3OUT R3 R3IN 18 RS-232

OUTPUTS INPUTS

5kΩ

11 R4OUT R4 R4IN 12

5kΩ

10 R5OUT R5 R5IN 9

EN 5kΩ 15

14 N.C.

GND

Figure 17. MAX239 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 26

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V INPUT

TOP VIEW 1.0μF

25 19 1.0μF

C1+ VCC 26

1.0μF 27 +5V TO +10V V+

28 C1- VOLTAGE DOUBLER

C2+ +5V TO -10V 30

1.0μF 29 VOLTAGE INVERTER V-

C2- 1.0μF

+5V

400kΩ

15 T1IN T1 T1OUT 7

+5V 400kΩ

14 T2IN T2 T2OUT 8

N.C. R2IN N.C. T2OUT T1OUT T3OUT T4OUT R3IN R3OUT T5IN N.C. +5V 400kΩ

TTL/CMOS 37 T3IN T3 T3OUT 6 RS-232

11 10 9 8 7 6 5 4 3 2 1 INPUTS OUTPUTS

+5V 400kΩ

N.C. 12 + 44 N.C. T4OUT

38 T4IN T4 5

R2OUT 13 43 SHDN

T2IN 14 42 EN +5V 400kΩ

T1IN 15 41 T5OUT

R1OUT 16 40 R4IN 2 T5IN T5 T5OUT 41

R1IN 17 MAX240 39 R4OUT

GND 18 38 T4IN 16 R1OUT R1 R1IN 17

VCC 19 37 T3IN

N.C. 20 36 R5OUT 5kΩ

N.C. 21 35 R5IN

N.C. 22 34 N.C. 13 R2OUT R2 R2IN 10

23 24 25 26 27 28 29 30 31 32 33 5kΩ

TTL/CMOS 3 R3OUT R3 R3IN 4 RS-232

N.C. N.C. C1+ V+ C1- C2+ C2 V- N.C. N.C. N.C. OUTPUTS INPUTS

5kΩ

Plastic FP

39 R4OUT R4 R4IN 40

5kΩ

36 R5OUT R5 R5IN 35

5kΩ

42 EN SHDN 43

GND

Figure 18. MAX240 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 27

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +5V INPUT

0.1μF 0.1μF

1 C1+ VCC

+5V TO +10V V+ 2 +10V

0.1μF 3 VOLTAGE DOUBLER

C1-

+ 4 C2+

C1+ 1 16 VCC +10V TO -10V V- 6 -10V

0.1μF 5 C2- VOLTAGE INVERTER

V+ 2 15 GND 0.1μF

C1- 3 14 T1OUT +5V

C2+ 4 MAX243 13 R1IN 400kΩ

C2- 5 12 R1OUT 11 T1IN T1OUT 14

V- 6 11 T1IN +5V

TTL/CMOS 400kΩ RS-232

T2OUT 7 10 T2IN INPUTS OUTPUTS

R2IN 8 9 R2OUT 10 T2IN T2OUT 7

DIP/SO

12 R1OUT R1IN 13

TTL/CMOS 5kΩ RS-232

OUTPUTS INPUTS

9 R2OUT R2IN 8

RECEIVER INPUT R1 OUTPUT R2 OUTPUT 5kΩ

≤ -3V HIGH HIGH

OPEN HIGH LOW

≥ +3V LOW LOW GND

Figure 19. MAX243 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 28

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V

TOP VIEW 1μF

1μF

21 20

1μF C1+ VCC 22

RA4IN RA5IN TA4OUT TA3OUT TA2OUT TA1OUT TB1OUT TB2OUT TB3OUT TB4OUT RB5IN 23 C1- +5V TO +10V VOLTAGE DOUBLER V+ 26

24 C2+ V-

1μF 25 C2- 1μF

6 5 4 3 2 1 44 43 42 41 40 +10V TO -10V VOLTAGE INVERTER

+ 2 TA1OUT +5V +5V TB1OUT 44

400kΩ

RA3IN 7 39 RB4IN 15 TA1IN TB1IN 30

RA2IN 8 38 RB3IN 2 TA2OUT +5V +5V TB2OUT 43

RA1IN 9 37 RB2IN 400kΩ

RA1OUT 10 36 RB1IN 16 TA2IN TB2IN 29

RA2OUT 11 35 RB1OUT

RA3OUT 12 MAX244 34 RB2OUT 3 TA3OUT +5V +5V TB3OUT 42

RA4OUT 13 33 RB3OUT 400kΩ

RA5OUT 14 32 RB4OUT 17 TA3IN TB3IN 28

TA1IN 15 31 RB5OUT 4 TA4OUT +5V +5V TB4OUT 41

TA2IN 16 30 TB1IN 400kΩ

TA3IN 17 29 TB2IN 18 TA4IN TB4IN 27

9 RA1IN RB1IN 36

18 19 20 21 22 23 24 25 26 27 28

TA4IN GND VCC C1+ V+ C1- C2+ C2- V- TB4IN TB3IN

5kΩ 5kΩ

PLCC 10 RA1OUT RB1OUT 35

8 RA2IN RB2IN 37

MAX249 FUNCTIONAL DESCRIPTION 5kΩ 5kΩ

10 RECEIVERS 11 RA2OUT RB2OUT 34

5 A-SIDE RECEIVERS 7 RA3IN RB3IN 38

5 B-SIDE RECEIVERS

8 TRANSMITTERS 5kΩ 5kΩ

4 A-SIDE TRANSMITTERS

4 B-SIDE TRANSMITTERS 12 RA3OUT RB3OUT 33

NO CONTROL PINS 6 RA4IN RB4IN 39

5kΩ 5kΩ

13 RA4OUT RB4OUT 32

5 RA5IN RB5IN 40

5kΩ 5kΩ

14 RA5OUT RB5OUT 31

GND

Figure 20. MAX244 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 29

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V

TOP VIEW 1μF

+ VCC

ENR 1 40 VCC 16 TA1OUT +5V +5V TB1OUT 24

TA1IN 2 39 ENT 400kΩ

2 TA1IN TB1IN 38

TA2IN 3 38 TB1IN

TA3IN 4 37 TB2IN 17 TA2OUT +5V +5V TB2OUT 23

TA4IN 5 36 TB3IN 400kΩ

3 TA2IN TB2IN 37

RA5OUT 6 35 TB4IN

RA4OUT 7 MAX245 34 RB5OUT 18 TA3OUT +5V +5V TB3OUT 22

RA3OUT 8 33 RB4OUT 400kΩ

4 TA3IN TB3IN 36

RA2OUT 9 32 RB3OUT +5V +5V

19 TA4OUT TB4OUT 21

RA1OUT 10 31 RB2OUT

400kΩ

RA1IN 11 30 RB1OUT 5 TA4IN TB4IN 35

RA2IN 12 29 RB1IN 1 ENR ENT 39

RA3IN 13 28 RB2IN

RA4IN 14 27 RB3IN 11 RA1IN RB1IN 29

RA5IN 15 26 RB4IN 5kΩ 5kΩ

TA1OUT 16 25 RB5IN

TA2OUT 17 24 TB1OUT 10 RA1OUT RB1OUT 30

TA3OUT 18 23 TB2OUT 12 RA2IN RB2IN 28

TA4OUT 19 22 TB3OUT 5kΩ 5kΩ

GND 20 21 TB4OUT

9 RA2OUT RB2OUT 31

DIP 13 RA3IN RB3IN 27

5kΩ 5kΩ

MAX245 FUNCTIONAL DESCRIPTION 8 RA3OUT RB3OUT 32

10 RECEIVERS 14 RA4IN RB4IN 26

5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE)

5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE) 5kΩ 5kΩ

8 TRANSMITTTERS 7 RA4OUT RB4OUT 33

4 A-SIDE TRANSMITTERS 15 RA5IN RB5IN 25

2 CONTROL PINS

1 RECEIVER ENABLE (ENR) 5kΩ 5kΩ

1 TRANSMITTER ENABLE (ENT)

6 RA5OUT RB5OUT 34

GND

Figure 21. MAX245 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 30

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V

TOP VIEW

1μF

+ 40

ENA 1 40 VCC +5V VCC +5V

TA1IN 2 39 ENB 16 TA1OUT TB1OUT 24

TA2IN 3 38 TB1IN 400kΩ

2 TA1IN TB1IN 38

TA3IN 4 37 TB2IN +5V +5V

TA4IN 5 36 TB3IN 17 TA2OUT TB2OUT 23

RA5OUT 6 35 TB4IN 400kΩ

3 TA2IN TB2IN 37

RA4OUT 7 MAX246 34 RB5OUT +5V +5V

RA3OUT 8 33 RB4OUT 18 TA3OUT TB3OUT 22

RA2OUT 9 32 RB3OUT 400kΩ

4 TA3IN TB3IN 36

RA1OUT 10 31 RB2OUT +5V +5V

RA1IN 11 30 RB1OUT 19 TA4OUT TB4OUT 21

RA2IN 12 29 RB1IN 400kΩ

5 TA4IN TB4IN 35

RA3IN 13 28 RB2IN

1 ENA ENB 39

RA4IN 14 27 RB3IN

11 RA1IN RB1IN 29

RA5IN 15 26 RB4IN

TA1OUT 16 25 RB5IN 5kΩ 5kΩ

TA2OUT 17 24 TB1OUT

10 RA1OUT RB1OUT 30

TA3OUT 18 23 TB2OUT 12 RA2IN RB2IN 28

TA4OUT 19 22 TB3OUT

GND 20 21 TB4OUT 5kΩ 5kΩ

DIP 9 RA2OUT RB2OUT 31

13 RA3IN RB3IN 27

MAX246 FUNCTIONAL DESCRIPTION 5kΩ 5kΩ

10 RECEIVERS 8 RA3OUT RB3OUT 32

5 A-SIDE RECEIVERS (RA5 ALWAYS ACTIVE) 14 RA4IN RB4IN 26

5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)

8 TRANSMITTERS 5kΩ 5kΩ

4 A-SIDE TRANSMITTERS

4 B-SIDE TRANSMITTERS 7 RA4OUT RB4OUT 33

2 CONTROL PINS 15 RA5IN RB5IN 25

ENABLE A-SIDE (ENA)

ENABLE B-SIDE (ENB) 5kΩ 5kΩ

6 RA5OUT GND RB5OUT 34

Figure 22. MAX246 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 31

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

+5V

TOP VIEW 1μF

+ 1 ENTA VCC ENTB 39

ENTA 1 40 VCC +5V +5V

16 TA1OUT TB1OUT 24

TA1IN 2 39 ENTB 400kΩ

TA2IN 3 38 TB1IN 2 TA1IN TB1IN 38

TA3IN 4 37 TB2IN +5V +5V

TA4IN 5 36 17 TA2OUT TB2OUT 23

TB3IN 400kΩ

RB5OUT 6 35 TB4IN 3 TA2IN TB2IN 37

RA4OUT 7 MAX247 34 RB4OUT +5V +5V

RA3OUT 8 33 RB3OUT 18 TA3OUT TB3OUT 22

RA2OUT 9 32 RB2OUT 400kΩ

4 TA3IN TB3IN 36

RA1OUT 10 31 RB1OUT +5V +5V

ENRA 11 30 ENRB 19 TA4OUT TB4OUT 21

RA1IN 12 29 RB1IN 400kΩ

5 TA4IN TB4IN 35

RA2IN 13 28 RB2IN 6 RB5OUT RB5IN 25

RA3IN 14 27 RB3IN

RA4IN 15 26 RB4IN 5kΩ

TA1OUT 16 25 RB5IN

TA2OUT 17 24 TB1OUT 12 RA1IN RB1IN 29

TA3OUT 18 23 TB2OUT

5kΩ 5kΩ

TA4OUT 19 22 TB3OUT

GND 20 21 TB4OUT 10 RA1OUT RB1OUT 31

13 RA2IN RB2IN 28

DIP

5kΩ 5kΩ

MAX247 FUNCTIONAL DESCRIPTION

9 RECEIVERS 9 RA2OUT RB2OUT 32

4 A-SIDE RECEIVERS 14 RA3IN RB3IN 27

5 B-SIDE RECEIVERS (RB5 ALWAYS ACTIVE)

8 TRANSMITTERS 5kΩ 5kΩ

4 A-SIDE TRANSMITTERS

4 B-SIDE TRANSMITTERS 8 RA3OUT RB3OUT 33

4 CONTROL PINS 15 RA4IN RB4IN 26

ENABLE RECEIVER A-SIDE (ENRA)

ENABLE RECEIVER B-SIDE (ENRB) 5kΩ 5kΩ

ENABLE RECEIVER A-SIDE (ENTA) 7 RA4OUT RB4OUT 34

ENABLE RECEIVER B-SIDE (ENTB) 11 ENRA ENRB 30

GND

Figure 23. MAX247 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 32

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +5V

1μF

21 20

TA4OUT TA3OUT TA2OUT TA1OUT TB1OUT TB2OUT TB3OUT TA4OUT 1μF C1+ VCC V+ 22

RA3IN RA4IN RB4IN 23 C1- +5V TO +10V VOLTAGE DOUBLER 26

24 C2+ V-

43 1μF 1μF

6 5 4 3 2 1 44 42 41 40 25 C2- +10V TO -10V VOLTAGE INVERTER

+ 18 ENTA ENTB 27

+5V +5V

1 TA1OUT TB1OUT 44

RA2IN 7 39 RB3IN 400kΩ

RA1IN 8 38 RB2IN 14 TA1IN TB1IN 31

ENRA 9 37 RB1IN +5V +5V

RA1OUT 10 36 ENRB 2 TA2OUT TB2OUT 43

RA2OUT 11 35 RB1OUT 400kΩ

RA3OUT 12 MAX248 34 RB2OUT 15 TA2IN TB2IN 30

RA4OUT 13 33 RB3OUT +5V +5V

TA1IN 14 32 RB4OUT 3 TA3OUT TB3OUT 42

TA2IN 15 31 TB1IN 400kΩ

TA3IN 16 30 TB2IN 16 TA3IN TB3IN 29

TA4IN 17 29 TB3IN +5V +5V

4 TA4OUT TB4OUT 41

18 19 20 21 22 23 24 25 26 27 28 400kΩ

ENTA GND VCC C1+ V+ C1- C2+ C2- V- ENTB TB4IN 17 TA4IN TB4IN 28

PLCC 8 RA1IN RB1IN 37

5kΩ 5kΩ

MAX248 FUNCTIONAL DESCRIPTION 10 RA1OUT RB1OUT 35

8 RECEIVERS 7 RA2IN RB2IN 38

4 A-SIDE RECEIVERS

4 B-SIDE RECEIVERS 5kΩ 5kΩ

8 TRANSMITTERS

4 A-SIDE TRANSMITTERS 11 RA2OUT RB2OUT 34

4 B-SIDE TRANSMITTERS 6 RA3IN RB3IN 39

4 CONTROL PINS

ENABLE RECEIVER A-SIDE (ENRA) 5kΩ 5kΩ

ENABLE RECEIVER B-SIDE (ENRB) 12 RA3OUT RB3OUT 33

ENABLE RECEIVER A-SIDE (ENTA) 5 RA4IN RB4IN 40

ENABLE RECEIVER B-SIDE (ENTB)

5kΩ 5kΩ

13 RA4OUT RB4OUT 32

9 ENRA ENRB 36

GND

Figure 24. MAX248 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 33

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

TOP VIEW +5V

1μF

21 20

TA3OUT TA2OUT TA1OUT TB1OUT TB2OUT TB3OUT 1μF C1+ VCC V+ 22

RA3IN RA4IN RA5IN RB5IN RB4IN 23 C1- +5V TO +10V VOLTAGE DOUBLER 26

24 C2+ V-

43 1μF 1μF

6 5 4 3 2 1 44 42 41 40 25 C2- +10V TO -10V VOLTAGE INVERTER

+ 18 ENTA ENTB 27

+5V +5V

1 TA1OUT TB1OUT 44

RA2IN 7 39 RB3IN 400kΩ

RA1IN 8 38 RB2IN 15 TA1IN TB1IN 30

ENRA 9 37 RB1IN +5V +5V

RA1OUT 10 36 ENRB 2 TA2OUT TB2OUT 43

RA2OUT 11 35 RB1OUT 400kΩ

RA3OUT 12 MAX249 34 RB2OUT 16 TA2IN TB2IN 29

RA4OUT 13 33 RB3OUT +5V +5V

RA5OUT 14 32 RB4OUT 3 TA3OUT TB3OUT 42

TA1IN 15 31 RB5OUT 400kΩ

TA2IN 16 30 TB1IN 17 TA3IN TB3IN 28

TA3IN 17 29 TB2IN 8 RA1IN RB1IN 37

18 19 20 21 22 23 24 25 26 27 28 5kΩ 5kΩ

ENTA GND VCC C1+ V+ C1- C2+ C2- V- ENTB TB3IN

10 RA1OUT RB1OUT 35

PLCC 7 RA2IN RB2IN 38

5kΩ 5kΩ

MAX249 FUNCTIONAL DESCRIPTION 11 RA2OUT RB2OUT 34

10 RECEIVERS 6 RA3IN RB3IN 39

5 A-SIDE RECEIVERS

5 B-SIDE RECEIVERS 5kΩ 5kΩ

6 TRANSMITTERS 12 RA3OUT RB3OUT 33

3 A-SIDE TRANSMITTERS 5 RA4IN RB4IN 40

3 B-SIDE TRANSMITTERS

4 CONTROL PINS 5kΩ 5kΩ

ENABLE RECEIVER A-SIDE (ENRA)

ENABLE RECEIVER B-SIDE (ENRB) 13 RA4OUT RB4OUT 32

ENABLE RECEIVER A-SIDE (ENTA) 4 RA5IN RB5IN 41

ENABLE RECEIVER B-SIDE (ENTB)

5kΩ 5kΩ

14 RA5OUT RB5OUT 31

9 ENRA ENRB 36

GND

Figure 25. MAX249 Pin Configuration and Typical Operating Circuit

www.maximintegrated.com Maxim Integrated | 34

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Ordering Information (continued)

PART TEMP R ANGE PIN-PACKAGE PART TEMP R ANGE PIN-PACKAGE

MAX220CPE+ 0°C to +70°C 16 Plastic DIP MAX231EW E+ -40°C to +85°C 16 W ide SO

MAX220CSE+ 0°C to +70°C 16 Narrow SO MAX231EJD -40°C to +85°C 14 CERDIP

MAX220CW E+ 0°C to +70°C 16 W ide SO MAX231MJD 55°C to +125°C 14 CERDIP

MAX220C/D 0°C to +70°C Dic e* MAX232CPE+ 0°C to +70°C 16 Plastic DIP

MAX220EPE+ -40°C to +85°C 16 Plastic DIP MAX232CSE+ 0°C to +70°C 16 Narrow SO

MAX220ESE+ -40°C to +85°C 16 Narrow SO MAX232CW E+ 0°C to +70°C 16 W ide SO

MAX220EW E+ -40°C to +85°C 16 W ide SO MAX232C/D 0°C to +70°C Dic e*

MAX220EJE -40°C to +85°C 16 CERDIP MAX232EPE+ -40°C to +85°C 16 Plastic DIP

MAX220MJE 55°C to +125°C 16 CERDIP MAX232ESE+ -40°C to +85°C 16 Narrow SO

MAX222CPN+ 0°C to +70°C 18 Plastic DIP MAX232EW E+ -40°C to +85°C 16 W ide SO

MAX222CW N+ 0°C to +70°C 18 W ide SO MAX232EJE -40°C to +85°C 16 CERDIP

MAX222C/D 0°C to +70°C Dic e* MAX232MJE 55°C to +125°C 16 CERDIP

MAX222EPN+ -40°C to +85°C 18 Plastic DIP MAX232MLP+ 55°C to +125°C 20 LCC

MAX222EW N+ -40°C to +85°C 18 W ide SO MAX232ACPE+ 0°C to +70°C 16 Plastic DIP

MAX222EJN -40°C to +85°C 18 CERDIP MAX232ACSE+ 0°C to +70°C 16 Narrow SO

MAX222MJN 55°C to +125°C 18 CERDIP MAX232ACW E+ 0°C to +70°C 16 W ide SO

MAX223CAI+ 0°C to +70°C 28 SSOP MAX232AC/D 0°C to +70°C Dic e*

MAX223CW I+ 0°C to +70°C 28 W ide SO MAX232AEPE+ -40°C to +85°C 16 Plastic DIP

MAX223C/D 0°C to +70°C Dic e* MAX232AESE+ -40°C to +85°C 16 Narrow SO

MAX223EAI+ -40°C to +85°C 28 SSOP MAX232AEW E+-40°C to +85°C 16 W ide SO

MAX223EW I+ -40°C to +85°C 28 W ide SO MAX232AEJE -40°C to +85°C 16 CERDIP

MAX225CW I+ 0°C to +70°C 28 W ide SO MAX232AMJE 55°C to +125°C 16 CERDIP

MAX225EW I+ -40°C to +85°C 28 W ide SO MAX232AMLP+ 55°C to +125°C 20 LCC

MAX230CPP+ 0°C to +70°C 20 Plastic DIP1 MAX233CPP+ 0°C to +70°C 20 Plastic DIP

MAX230CW P+ 0°C to +70°C 20 W ide SO MAX233EPP+ -40°C to +85°C 20 Plastic DIP

MAX230C/D 0°C to +70°C Dic e* MAX233ACPP+ 0°C to +70°C 20 Plastic DIP

MAX230EPP+ -40°C to +85°C 20 Plastic DIP MAX233ACW P+ 0°C to +70°C 20 W ide SO

MAX230EW P+ -40°C to +85°C 20 W ide SO MAX233AEPP+ -40°C to +85°C 20 Plastic DIP

MAX230EJP -40°C to +85°C 20 CERDIP MAX233AEW P+-40°C to +85°C 20 W ide SO

MAX230MJP 55°C to +125°C 20 CERDIP MAX234CPE+ 0°C to +70°C 16 Plastic DIP

MAX231CPD+ 0°C to +70°C 14 Plastic DIP MAX234CW E+ 0°C to +70°C 16 W ide SO

MAX231CW E+ 0°C to +70°C 16 W ide SO MAX234C/D 0°C to +70°C Dic e*

MAX231CJD 0°C to +70°C 14 CERDIP MAX234EPE+ -40°C to +85°C 16 Plastic DIP

MAX231C/D 0°C to +70°C Dic e* +Denotes a lead(Pb)-free/RoHS-compliant package.

MAX231EPD+ -40°C to +85°C 14 Plastic DIP *Contact factory for dice specifications.

www.maximintegrated.com Maxim Integrated | 35

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Ordering Information (continued)

PART TEMP R ANGE PIN-PACKAGE PART TEMP R ANGE PIN-PACKAGE

MAX234EW E+ -40°C to +85°C 16 W ide SO MAX240CMH+ 0°C to +70°C 44 Plastic FP

MAX234EJE -40°C to +85°C 16 CERDIP MAX240C/D 0°C to +70°C Dic e*

MAX234MJE 55°C to +125°C 16 CERDIP MAX241CAI+ 0°C to +70°C 28 SSOP

MAX235CPG+ 0°C to +70°C 24 W ide Plastic DIP MAX241CW I+ 0°C to +70°C 28 W ide SO

MAX235EPG+ -40°C to +85°C 24 W ide Plastic DIP MAX241C/D 0°C to +70°C Dic e*

MAX235EDG -40°C to +85°C 24 Ceramic SB MAX241EAI+ -40°C to +85°C 28 SSOP

MAX235MDG 55°C to +125°C 24 Ceramic SB MAX241EW I+ -40°C to +85°C 28 W ide SO

MAX236CNG+ 0°C to +70°C 24 Narrow Plastic DIP MAX242CAP+ 0°C to +70°C 20 SSOP

MAX236CW G+ 0°C to +70°C 24 W ide SO MAX242CPN+ 0°C to +70°C 18 Plastic DIP

MAX236C/D 0°C to +70°C Dic e* MAX242CW N+ 0°C to +70°C 18 W ide SO

MAX236ENG+ -40°C to +85°C 24 Narrow Plastic DIP MAX242C/D 0°C to +70°C Dic e*

MAX236EW G+ -40°C to +85°C 24 W ide SO MAX242EPN+ -40°C to +85°C 18 Plastic DIP

MAX236ERG -40°C to +85°C 24 Narrow CERDIP MAX242EW N+ -40°C to +85°C 18 W ide SO

MAX236MRG 55°C to +125°C 24 Narrow CERDIP MAX242EJN -40°C to +85°C 18 CERDIP

MAX237CNG+ 0°C to +70°C 24 Narrow Plastic DIP MAX242MJN 55°C to +125°C 18 CERDIP

MAX237CW G+ 0°C to +70°C 24 W ide SO MAX243CPE+ 0°C to +70°C 16 Plastic DIP

MAX237C/D 0°C to +70°C Dic e* MAX243CSE+ 0°C to +70°C 16 Narrow SO

MAX237ENG+ -40°C to +85°C 24 Narrow Plastic DIP MAX243CW E+ 0°C to +70°C 16 W ide SO

MAX237EW G+ -40°C to +85°C 24 W ide SO MAX243C/D 0°C to +70°C Dic e*

MAX237ERG -40°C to +85°C 24 Narrow CERDIP MAX243EPE+ -40°C to +85°C 16 Plastic DIP

MAX237MRG 55°C to +125°C 24 Narrow CERDIP MAX243ESE+ -40°C to +85°C 16 Narrow SO

M AX2 38 CNG + 0°C to +70°C 24 Narrow Plastic DIP MAX243EW E+ -40°C to +85°C 16 W ide SO

MAX238CW G+ 0°C to +70°C 24 W ide SO MAX243EJE -40°C to +85°C 16 CERDIP

MAX238C/D 0°C to +70°C Dic e* MAX243MJE 55°C to +125°C 16 CERDIP

MAX238ENG+ -40°C to +85°C 24 Narrow Plastic DIP MAX244CQH+ 0°C to +70°C 44 PLCC

MAX238EW G+ -40°C to +85°C 24 W ide SO MAX244C/D 0°C to +70°C Dic e*

MAX238ERG -40°C to +85°C 24 Narrow CERDIP MAX244EQH+ -40°C to +85°C 44 PLCC

MAX238MRG 55°C to +125°C 24 Narrow CERDIP M AX2 4 5C PL + 0°C to +70°C 40 Plastic DIP

MAX239CNG+ 0°C to +70°C 24 Narrow Plastic DIP MAX245C/D 0°C to +70°C Dic e*

MAX239CW G+ 0°C to +70°C 24 W ide SO MAX245EPL+ -40°C to +85°C 40 Plastic DIP

MAX239C/D 0°C to +70°C Dic e* MAX246CPL+ 0°C to +70°C 40 Plastic DIP

MAX239ENG+ -40°C to +85°C 24 Narrow Plastic DIP MAX246C/D 0°C to +70°C Dic e*

MAX239EW G+ -40°C to +85°C 24 W ide SO MAX246EPL+ -40°C to +85°C 40 Plastic DIP

MAX239ERG -40°C to +85°C 24 Narrow CERDIP +Denotes a lead(Pb)-free/RoHS-compliant package.

*Contact factory for dice specifications.

MAX239MRG 55°C to +125°C 24 Narrow CERDIP

www.maximintegrated.com Maxim Integrated | 36

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Ordering Information (continued)

PART TEMP R ANGE PIN-PACKAGE

MAX247CPL+ 0°C to +70°C 40 Plastic DIP

MAX247C/D 0°C to +70°C Dic e*

MAX247EPL+ -40°C to +85°C 40 Plastic DIP

MAX248CQH+ 0°C to +70°C 44 PLCC

MAX248C/D 0°C to +70°C Dic e*

MAX248EQH+ -40°C to +85°C 44 PLCC

MAX249CQH+ 0°C to +70°C 44 PLCC

MAX249EQH+ -40°C to +85°C 44 PLCC

+Denotes a lead(Pb)-free/RoHS-compliant package.

*Contact factory for dice specifications.

Selection Table

Power No. of No. of Nominal SHDN Rx Data

Part Supply RS-232 Ext. Cap. Value & Active Rate Features

Number (V) Drivers Caps (+F) Three- in (kbps)

/Rx State SHDN

MAX220 +5 2/2 4 0.047, 0.33 No No 120 Ultra-low-power, industry-standard pinout

MAX222 +5 2/2 4 0.1 Yes No 200 Low-power shutdown

MAX223 +5 4/5 4 1.0, 0.1 Yes Yes 120 MAX241 and receivers active in shutdown

MAX225 +5 5/5 0 — Yes Yes 120 Available in SO

MAX230 +5 5/0 4 1.0, 0.1 Yes No 120 5 drivers with shutdown

MAX231 +5 and 2/2 2 1.0, 0.1 No No 120 Standard +5/+12V or battery supplies;

+7.5 to same functions as MAX232

MAX232 +5 2/2 4 1.0, 0.1 No No 120 (64) Industry standard

MAX232A +5 2/2 4 0.1 No No 200 Higher slew rate, small caps

MAX233 +5 2/2 0 — No No 120 No external caps

MAX233A +5 2/2 0 — No No 200 No external caps, high slew rate

MAX234 +5 4/0 4 1.0, 0.1 No No 120 Replaces 1488

MAX235 +5 5/5 0 — Yes No 120 No external caps

MAX236 +5 4/3 4 1.0, 0.1 Yes No 120 Shutdown, three state

MAX237 +5 5/3 4 1.0, 0.1 No No 120 Complements IBM PC serial port

MAX238 +5 4/4 4 1.0, 0.1 No No 120 Replaces 1488 and 1489

MAX239 +5 and 3/5 2 1.0, 0.1 No No 120 Standard +5/+12V or battery supplies;

+7.5 to single-package solution for IBM PC serial

MAX240 +5 5/5 4 1.0 Yes No 120 DIP or flatpack package

MAX241 +5 4/5 4 1.0, 0.1 Yes No 120 Complete IBM PC serial port

MAX242 +5 2/2 4 0.1 Yes Yes 200 Separate shutdown and enable

MAX243 +5 2/2 4 0.1 No No 200 Open-line detection simplifies cabling

MAX244 +5 8/10 4 1.0 No No 120 High slew rate

MAX245 +5 8/10 0 — Yes Yes 120 High slew rate, int. caps, two shutdown

MAX246 +5 8/10 0 — Yes Yes 120 High slew rate, int. caps, three shutdown

MAX247 +5 8/9 0 — Yes Yes 120 High slew rate, int. caps, nine operating

MAX248 +5 8/8 4 1.0 Yes Yes 120 High slew rate, selective half-chip enables

MAX249 +5 6/10 4 1.0 Yes Yes 120 Available in quad flatpack package

www.maximintegrated.com Maxim Integrated | 37

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Package Information

For the latest package outline information and land patterns (footprints), go to www.maximintegrated.com/packages. Note that a “+”, “#”, or

“-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the

package regardless of RoHS status.

PACKAGE PACKAGE OUTLINE LAND PACKAGE PACKAGE OUTLINE LAND

TYPE CODE NO. PATTERN NO. TYPE CODE NO. PATTERN NO.

14 PDIP P14+3 16 SO(W) W16+1

16 PDIP P16+1 16 SO(W) W16+2 90-0107

16 PDIP P16+2 16 SO(W) W16+3

16 PDIP P16+3 21-0043 18 SO(W) W18+1 90-0181

18 PDIP P18+5 20 SO(W) W20+3

20 PDIP P20+3 20 SO(W) W20M+1 21-0042 90-0108

20 PDIP P20M+1 24 SO(W) W24+2 90-0182

24 PDIP N24+3 28 SO(W) W28+1

24 PDIP P24M+1 — 28 SO(W) W28+2 90-0109

28 PDIP P28+2 21-0044 28 SO(W) W28M+1

40 PDIP P40+1 20 LCC L20+3 21-0658 90-0177

40 PDIP P40M+2 20 SSOP A20+1 90-0094

14 CERDIP J14-3 24 SSOP A24+2 90-0110

16 CERDIP J16-3 28 SSOP A28+1 21-0056 90-0095

18 CERDIP J18-2 21-0045 16 TSSOP U16+1 90-0117

20 CERDIP J20-2 16 FPCK F16-3 21-0013 —

24 CERDIP R24-4 44 MQFP M44+5 21-0826 90-0169

16 SO(N) S16+3 21-0041 90-0097 44 PLCC Q44+1

16 SO(N) S16+5 44 PLCC Q44+2 21-0049 90-0236

www.maximintegrated.com Maxim Integrated | 38

MAX220–MAX249 +5V-Powered, Multichannel

RS-232 Drivers/Receivers

Revision History

REVISION REVISION DESCRIPTION PAGES

NUMBER DATE CHANGED

15 1/06 Added part information to the lead temperature in the Absolute Maximum Ratings 2, 5, 8

sections

Changed multiple packages to lead-free versions; updated/added notes 3, 4, 5, 7, and

16 7/10 8 to the Electrical Characteristics table; removed incorrect subscripting from all pin 1, 2–9, 17–36

names in the Electrical Characteristics table and Pin Configurations

17 1/15 Updated General Description and Benefits and Features sections 1

For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated’s website at www.maximintegrated.com.

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent

licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and

max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Maxim Integrated:

MAX220CSE+ MAX222CPN+ MAX222CWN+ MAX222EWN+ MAX223EWI+ MAX225CWI+G36 MAX231CPD+

MAX231CWE+ MAX232ACPE+ MAX232ACSE+ MAX232ACWE+ MAX232AEPE+ MAX232AESE+ MAX232AEWE+

MAX232CPE+ MAX232CSE+ MAX232CWE+ MAX232EPE+ MAX232ESE+ MAX232EWE+ MAX233ACPP+G36

MAX233ACWP+G36 MAX233ACWP+TG36 MAX233AEPP+G36 MAX233AEWP+G36 MAX233CPP+G36

MAX233EPP+G36 MAX234CPE+ MAX235CPG+G36 MAX235EPG+G36 MAX236CNG+ MAX236CWG+

MAX236EWG+ MAX237CNG+ MAX237CWG+ MAX238CNG+ MAX238CWG+ MAX238EWG+ MAX239CNG+

MAX239CWG+ MAX241CWI+ MAX241EWI+ MAX242CPN+ MAX242CWN+ MAX242EPN+ MAX242EWN+

MAX243CSE+ MAX248CQH+D MAX248EQH+D MAX249CQH+D MAX4567CSE+T MAX4567EEE+T

MAX220MJE/883B MAX231MJD/883B MAX232AMJE/883B MAX232EJE MAX232MJE/883B MAX232MLP/883B

MAX234MJE/883B MAX243MJE/883B MAX233AEWP-T MAX222EWN-T MAX220CPE+ MAX220CSE+T

MAX220CWE+ MAX220CWE+T MAX220EPE+ MAX220ESE+ MAX220ESE+T MAX220EWE+ MAX220EWE+T

MAX222CPN MAX222CWN+T MAX222EPN+ MAX222EWN MAX222EWN+T MAX223CAI+ MAX223CAI+T

MAX223CWI+ MAX223CWI+T MAX223EAI+ MAX223EAI+T MAX223EWI+T MAX225CWI+TG36 MAX225EWI+G36

MAX225EWI+TG36 MAX230CPP+ MAX230CWP+ MAX230CWP+T MAX230EPP+ MAX230EWP+

MAX230EWP+T MAX231CWE+T MAX231EPD+ MAX231EWE+ MAX231EWE+T MAX232ACPE MAX232ACSE+T

MAX232ACWE+T MAX232AESE+T

电路和微电子考研

关注

0
点赞
踩
0

收藏

觉得还不错? 一键收藏
0
评论
惠普计算机X9W2AV参数,MAX220CPE,MAX220CPE pdf中文资料,MAX220CPE引脚图,MAX220CPE电路-Datasheet-电子工程世界...

MAX220–MAX249 +5V-Powered, MultichannelRS-232 Drivers/ReceiversGeneral Description ...
复制链接

扫一扫