linux uboot环境变量,linux 下更新uboot环境变量

参考网址：

代码分析：

README：

This is a demo implementation of a Linux command line tool to access

the U-Boot's environment variables.

For the run-time utiltity configuration uncomment the line

#define CONFIG_FILE  "/etc/fw_env.config"

in fw_env.h.

这个有误，应该是用配置文件时，不要注释掉这个宏

See comments in the fw_env.config file for definitions for the

particular board.

Configuration can also be done via #defines in the fw_env.h file. The

following lines are relevant:

#define HAVE_REDUND    /* For systems with 2 env sectors */

#define DEVICE1_NAME    "/dev/mtd1"

#define DEVICE2_NAME    "/dev/mtd2"

#define DEVICE1_OFFSET    0x0000

#define ENV1_SIZE         0x4000

#define DEVICE1_ESIZE     0x4000

#define DEVICE2_OFFSET    0x0000

#define ENV2_SIZE         0x4000

#define DEVICE2_ESIZE     0x4000

Current configuration matches the environment layout of the TRAB

board.

HAVE_REDUND是用来环境变量备份用的

Un-define HAVE_REDUND, if you want to use the utlities on a system

that does not have support for redundant environment enabled.

If HAVE_REDUND is undefined, DEVICE2_NAME is ignored,

as is ENV2_SIZE and DEVICE2_ESIZE.

The DEVICEx_NAME constants define which MTD character devices are to

be used to access the environment.

The DEVICEx_OFFSET constants define the environment offset within the

MTD character device.

ENVx_SIZE defines the size in bytes taken by the environment, which

may be less then flash sector size, if the environment takes less

then 1 sector.

DEVICEx_ESIZE defines the size of the first sector in the flash

partition where the environment resides.

DEVICEx_NAME设备名

DEVICEx_OFFSET设备中环境变量的偏移

ENVx_SIZE 环境变量大小，可能比1sector小

查看环境变量大小：

pri查看

Environment size: 1560/4092 bytes

include/configs/mv_kv.h

#define CFG_ENV_SIZE        0x1000

所以大小是0x1000

查看环境变量偏移：

#define CFG_MONITOR_LEN            (512 << 10)    /* Reserve 512 kB for Monitor */   uboot镜像长度 0x80000 =512k

//uboot的基址和环境变量的基址

#define CFG_MONITOR_BASE        (CFG_FLASH_BASE)

#define CFG_ENV_ADDR            (CFG_MONITOR_BASE + CFG_MONITOR_LEN)     环境变量开始位置

#define CFG_ENV_SIZE        0x1000   //4k

环境变量从0x80000开始 到0x80000+0x1000

根据CFG_ENV_ADDR 知道环境变量偏移是0x80000

查看erasesize

/opt/qtmarvell/mvqt/tools # cat /proc/mtd

dev:    size   erasesize  name

mtd0: 00100000 00010000 "uboot"

mtd1: 00700000 00010000 "linux-root"

编译fw_printenv:

根目录下：

make env HOSTCC=arm-mv5sft-linux-gnueabi-gcc

ln -s fw_printenv fw_setenv

修改fw_env.config ，根据上面的信息：

/opt/qtmarvell/mvqt/tools # cat fw_env.config

# Configuration file for fw_(printenv/saveenv) utility.

# Up to two entries are valid, in this case the redundant

# environment sector is assumed present.

# Notice, that the "Number of sectors" is ignored on NOR.

# MTD device name       Device offset   Env. size       Flash sector size       Number of sectors

/dev/mtd0               0x80000         0x1000          0x10000